|
|
PDF HC4P5509A1R3060 Data sheet ( Hoja de datos )
| Número de pieza | HC4P5509A1R3060 | |
| Descripción | SLIC Subscriber Line Interface Circuit | |
| Fabricantes | Intersil Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de HC4P5509A1R3060 (archivo pdf) en la parte inferior de esta página. Total 10 Páginas | ||
|
No Preview Available !
HC5509A1R3060
June 1997
SLIC
Subscriber Line Interface Circuit
Features
Description
• DI Monolithic High Voltage Process
• Compatible with Worldwide PBX and CO Performance
Requirements
• Controlled Supply of Battery Feed Current with
Programmable Current Limit
• Operates with 5V Positive Supply (VB+)
• Internal Ring Relay Driver and a Utility Relay Driver
• High Impedance Mode for Subscriber Loop
• High Temperature Alarm Output
• Low Power Consumption During Standby Functions
• Switch Hook, Ground Key, and Ring Trip Detection
• Selective Power Denial to Subscriber
• Voice Path Active During Power Denial
• On Chip Op Amp for 2-Wire Impedance Matching
The HC4P5509A1R3060 telephone Subscriber Line
Interface Circuit integrates most of the BORSCHT functions
on a monolithic IC. The device is manufactured in a
Dielectric Isolation (DI) process and is designed for use as a
high voltage interface between the traditional telephone
subscriber pair (Tip and Ring) and the low voltage filtering
and coding/decoding functions of the line card. Together with
a secondary protection diode bridge and “feed” resistors, the
device will withstand 1000V lightning induced surges, in
plastic packages. The SLIC also maintains specified
transmission performance in the presence of externally
induced longitudinal currents. The BORSCHT functions that
the SLIC provides are:
• Battery Feed with Subscriber Loop Current Limiting
• Overvoltage Protection
• Ring Relay Driver
• Supervisory Signaling Functions
• Hybrid Functions (with External Op Amp)
• Test (or Battery Reversal) Relay Driver
Applications
• Solid State Line Interface Circuit for PBX or Central
Office Systems, Digital Loop Carrier Systems
• Hotel/Motel Switching Systems
• Direct Inward Dialing (DID) Trunks
• Voice Messaging PBXs
• High Voltage 2-Wire/4-Wire, 4-Wire/2-Wire Hybrid
• Related Literature
- AN9607, Impedance Matching Design Equations
- AN9628, AC Voltage Gain
- AN9608, Implementing Pulse Metering
- AN549, The HC-5502S/4X Telephone Subscriber
Line Interface Circuits (SLIC)
In addition, the SLIC provides selective denial of power to
subscriber loops, a programmable subscriber loop current
limit from 20mA to 60mA, a thermal shutdown with an alarm
output and line fault protection. Switch hook detection, ring
trip detection and ground key detection functions are also
incorporated in the SLIC device.
The HC4P5509A1R3060 SLIC is ideally suited for line card
designs in PBX and CO systems, replacing traditional
transformer solutions.
Ordering Information
PART NUMBER
TEMP.
RANGE (oC) PACKAGE
PKG.
NO.
HC4P5509A1R3060
0 to 75 28 Ld PLCC N28.45
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
1
File Number 3675.3
1 page  
HC5509A1R3060
Pin Descriptions
SOIC
SYMBOL
1 AG
2 VB+
3 C1
4 PD
5 RC
6 RS
7 SHD
8 GKD
9 TST
10 ALM
11 ILMT
12 OUT1
13 -IN1
14 TIP
15 RING
16 RFS
17 VRX
18 LAO
DESCRIPTION
Analog Ground - To be connected to zero potential. Serves as a reference for the transmit output and re-
ceive input terminals.
Positive Voltage Source - Most Positive Supply.
Capacitor #C1 - An external capacitor to be connected between this terminal and analog ground. Required
for proper operation of the loop current limiting function.
Power Denial - A low active TTL-compatible logic input. When enabled, the output of the ring amplifier will
ramp to close to the output voltage of the tip amplifier.
Ring Command - A low active TTL-compatible logic input. When enabled, the relay driver (RD) output goes
low on the next high level of the ring sync (RS) input, as long as the SLIC is not in the power down mode
(TST = 0) or the subscriber is not already off-hook (SHD = 0).
Ring Synchronization Input - A TTL - compatible clock input. The clock is arranged such that a positive
pulse (50 - 500µs) occurs on the zero crossing of the ring voltage source, as it appears at the RFS terminal.
For Tip side injected systems, the RS pulse should occur on the negative going zero crossing and for Ring
injected systems, on the positive going zero crossing. This ensures that the ring relay activates and deac-
tivates when the instantaneous ring voltage is near zero. If synchronization is not required, the pin should
be tied to +5.
Switch Hook Detection - An active low LS TTL compatible logic output. A line supervisory output.
Ground Key Detection - An active low LS TTL compatible logic output. A line supervisory output.
A TTL logic input. A low on this pin will keep the SLIC in a power down mode. The TST pin in conjunction
with the ALM pin can provide thermal shutdown protection for the SLIC. Thermal shutdown is implemented
by a system controller that monitors the ALM pin. When the ALM pin is active (low) the system controller
issues a command to the Test pin (low) to power down the SLIC. The timing of the thermal recovery is con-
trolled by the system controller.
A TTL compatible active low output which responds to the thermal detector circuit when a safe operating
die temperature has been exceeded. Reference the TST pin description for a method to reduce prolonged
thermal overstress that may reduce component life.
Loop Current Limit - Voltage on this pin sets the short loop current limiting conditions using a resistive volt-
age divider.
The analog output of the spare operational amplifier.
The inverting analog input of the spare operational amplifier.
An analog input connected to the TIP (more positive) side of the subscriber loop through a feed resistor
and ring relay contact. Functions with the RING terminal to receive voice signals from the telephone and
for loop monitoring purpose.
An analog input connected to the RING (more negative) side of the subscriber loop through a feed resistor.
Functions with the TIP terminal to receive voice signals from the telephone and for loop monitoring purposes.
Ring Feed Sense - Senses RING side of the loop for Ground Key Detection. During Ring injected ringing
the ring signal at this node is isolated from RF via the ring relay. For Tip injected ringing, the RF and RFS
pins must be shorted.
Receive Input, 4-Wire Side - A high impedance analog input. AC signals appearing at this input drive the
Tip Feed and Ring Feed amplifiers differentially.
Longitudinal Amplifier Output - A low impedance output to be connected to C2 through a low pass filter.
Output is proportional to the difference in ITIP and IRING.
5
5 Page | ||
| Páginas | Total 10 Páginas | |
| PDF Descargar | [ Datasheet HC4P5509A1R3060.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| HC4P5509A1R3060 | SLIC Subscriber Line Interface Circuit | Intersil Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |