|
|
PDF USL1601 Data sheet ( Hoja de datos )
| Número de pieza | USL1601 | |
| Descripción | CONSTANT CURRENT CONTROLLER | |
| Fabricantes | Unisonic Technologies | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de USL1601 (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
|
No Preview Available !
UNISONIC TECHNOLOGIES CO., LTD
USL1601
Preliminary
CONSTANT CURRENT
CONTROLLER FOR
NON-ISOLATED BUCK LED
DRIVER
CMOS IC
DESCRIPTION
The UTC USL1601 is a high precision constant current
non-isolated buck LED driver controller. It can operate under
universal AC input, also can operate 12V~600V DC input. The UTC
USL1601 integrates 600V power MOSFET, so it can use very few
external components achieve excellent constant current
performance.
The UTC USL1601 uses high precision current sense circuit and
patent method for constant current control, to achieve high precision output current and excellent line regulation.
The UTC USL1601 operates in inductor current critical mode. The LED current is constant over wide range of
inductance variation and the LED output voltage, so the load regulation is excellent.
The UTC USL1601 operation current is 200µA only, so the auxiliary winding is not needed. It can simplify the
system design and reduce the system cost.
The UTC USL1601 offers rich protection functions, including LED short circuit protection, current sense resistor
short circuit protection and over temperature protection.
FEATURES
* Inductor current critical mode, No need to compensate the
inductance variation
* 600V MOSFET integrated
* ±3% LED current accuracy
* Source driver structure, Not need the auxiliary winding for VCC
ORDERING INFORMATION
* LED short circuit protection
* Up to 93% system efficiency
* Current sense resistor short circuit protection
* Over temperature protection
Ordering Number
USL1601G-S08-R
Package
SOP-8
Packing
Tape Reel
MARKING
www.unisonic.com.tw
Copyright © 2014 Unisonic Technologies Co., Ltd
1 of 6
QW-R125-033.a
1 page  
USL1601
Preliminary
CMOS IC
FUNCTION DESCRIPTION(Cont.)
Inductance Calculation
The UTC USL1601 is designed to work in inductor current critical mode, the energy will be stored in the inductor
when the MOSFET is turned on. The turn on time is given by:
ton
=
L ×IPK
VIN - VLED
The L is the inductance.
The IPK is the peak current in inductor.
The VIN is the input rectified voltage.
The VLED is the voltage on LED.
When the power MOSFET is turned off, the inductor current will decrease from the peak current to zero. The turn
off time is given by:
toff
=
L ×IPK
VLED
The MOSFET will be turned on again when it detects the inductor current goes to zero.
The inductance can be calculated by the following equation:
L
=
VLED × (VIN - VLED )
f ×IPK × VIN
The UTC USL1601 internally set the minimum off time to 4µs and maximum off time to 130µs. When the
inductance is very small, the toff may goes below the minimum off time and the inductor current becomes
discontinuous. So the output LED current will be smaller than the setting value. If the inductance is too large, the toff
may goes beyond the maximum off time and the inductor current becomes continuous. And the output LED current
will be larger than the setting value. So it’s very important to select a right inductance.
The UTC USL1601 also internally set the maximum on time to 40µs. When the input voltage is very low or LED
output voltage is very high, the ton may goes beyond the maximum on time. The power MOSFET will be turned off
even the inductor current still below the setting value. So the output LED current will be smaller than the setting
value.
Protection Functions
The UTC USL1601 has many protection functions, including LED short circuit protection, current sense resistor
short circuit protection and over temperature protection. All of the protection functions are designed to auto-recover.
The over temperature protection circuitry in the UTC USL1601 monitors the die junction temperature after start
up. When the temperature rises to 150°C, the power MOSFET will be shut down immediately and maintains at
switch off condition until the temperature on die falls 30°C below the thermal protection trigger point.
PCB Layout
The following guidelines should be followed in UTC USL1601 PCB layout:
Bypass Capacitor
The bypass capacitor on VCC pin should be as close as possible to the VCC and GND pins.
Ground Path
The power ground path for current sense should be short, and the power ground path should be separated from
small signal ground path before the negative node of the bus capacitor.
The Area of Power Loop
The area of main current loop should be as small as possible to reduce EMI radiation. And the controller should
be placed away from the heat generator, such as the power diode.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
5 of 6
QW-R125-033.a
5 Page | ||
| Páginas | Total 6 Páginas | |
| PDF Descargar | [ Datasheet USL1601.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| USL1601 | CONSTANT CURRENT CONTROLLER | Unisonic Technologies |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |