|
|
PDF AH3782 Data sheet ( Hoja de datos )
| Número de pieza | AH3782 | |
| Descripción | HIGH-SENSITIVITY HALL EFFECT LATCH | |
| Fabricantes | Diodes | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de AH3782 (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
|
No Preview Available !
Description
AH3782
HIGH-VOLTAGE, HIGH-SENSITIVITY HALL EFFECT LATCH
WITH INTERNAL PULL-UP RESISTOR
Pin Assignments
The AH3782 is a high-voltage, high-sensitivity Hall Effect latch IC
with internal pull-up resistor designed for commutation of brushless
DC motors, flow meters, linear encoders and position sensors in
industrial and consumer home appliances and personal care
applications. To support a wide range of demanding applications, the
design has been optimized to operate over the supply range of 3.0V
to 28V. With chopper stabilized architecture and an internal bandgap
regulator to provide temperature compensated supply for internal
circuits, the AH3782 provides a reliable solution over the whole
operating range. For robustness and protection, the device has a
Zener clamp on the supply. The output has an overcurrent limit and a
Zener clamp.
(Top View)
GND 2
3 OUTPUT
1 VDD
SC59 and SOT23
The internally pulled-up output can be switched on with South pole of
sufficient strength and switched off with North pole of sufficient
strength. When the magnetic flux density (B) perpendicular to the part
marking surface is larger than the operate point (BOP) the output is
switched on (pulled low). The output is held latched until magnetic flux
density reverses and becomes lower than the release point (BRP).
The magnetic operating and release polarity is opposite for SOT23
and SC59 packages. SOT23 and SIP-3 packages will require South
pole to the part marking side to operate while SC59 will require North
pole to the part marking side.
(Top View)
SIP-3
3. OUTPUT
2. GND
1. VDD
Features
• Bipolar Latch Operation (South Pole: On, North Pole: off)
• 3.0V to 28V Operating Voltage Range
• High Sensitivity: BOP and BRP of +40G and -40G Typical
• Internally Pull-up Resistor on the Output Pin
• Output Overcurrent Limit
• Chopper Stabilized Design Provides
- Superior Temperature Stability
- Minimal Switch Point Drift
- Enhanced Immunity to Stress
• Good RF Noise Immunity
• Zener Clamp on Supply and Output Pins
• -40°C to +125°C Operating Temperature
• ESD (HBM): 6kV
• Industry Standard SC59, SOT23 and SIP-3 Packages
• Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2)
• Halogen and Antimony Free. “Green” Device (Note 3)
Applications
• Brushless DC Motor Commutation
• Revolution Per Minute (RPM) Measurement
• Flow Meters
• Angular and Linear Encoder and Position Sensors
• Contact-less Commutation, Speed Measurement and Angular
Position Sensing/Indexing in Consumer Home Appliances, Office
Equipments and Industrial Applications
Notes:
1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant.
2. See http://www.diodes.com/quality/lead_free.html for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green"
and Lead-free.
3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and
<1000ppm antimony compounds.
AH3782
Document number: DS38083 Rev. 1 - 2
1 of 14
www.diodes.com
September 2015
© Diodes Incorporated
1 page  
Typical Operating Characteristics
Magnetic Operating Switch Points – BOP and BRP
100 TA = +25oC
80
60
40
20
0
-20
-40
-60
-80
-100
2468
Hyst
Bop
Brp
10 12 14 16 18 20 22 24 26 28 30
Supply Voltage (V)
Switch Points Bop and Brp vs Supply Voltage
AH3782
100 VDD = 3V
80
60
40
20
0
-20
-40
-60
-80
-100
-50
-25
0
Hyst
Bop
Brp
25 50 75 100 125 150
Temperature (oC)
Switch Points Bop and Brp vs Temperature
100 VDD = 12V
80
60
40
20
0
-20
-40
-60
-80
-100
-50
-25
0
Hyst
Bop
Brp
25 50 75 100 125 150
Temperature (oC)
Switch Points Bop and Brp vs Temperature
Supply Current
7.0
TA = +25 C
6.0
5.0
4.0
3.0
2.0
1.0
0.0
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30
Supply Voltage (V)
Supply Current vs Supply Voltage
100 VDD = 28V
80
60
40
20
0
-20
-40
-60
-80
-100
-50
-25
0
Hyst
Bop
Brp
25 50 75 100 125 150
Temperature (oC)
Switch Points Bop and Brp vs Temperature
7.0
28V
6.0
5.0
4.0
3.0
2.0 12V
3V
1.0
0.0
-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130
Temperature (oC)
Supply Current vs Temperature
AH3782
Document number: DS38083 Rev. 1 - 2
5 of 14
www.diodes.com
September 2015
© Diodes Incorporated
5 Page 
Package Outline Dimensions (cont.) (All dimensions in mm.)
Please see AP02002 at http://www.diodes.com/datasheets/ap02002.pdf for the latest version.
(3) Package Type: SIP-3 Bulk
a1
a2
B
P
A
EF
L
J
C
N
D
GH
a4
AH3782
SIP-3 (Bulk)
Dim Min
Max
A 3.9 4.3
a1 5° Typ
a2 5°Typ
a3 45° Typ
a4 3°Typ
B 2.8 3.2
C 1.40 1.60
D 0.33 0.432
E 0.40 0.508
F 0 0.2
G 1.24 1.30
H 2.51 2.57
J 0.35 0.43
L 14.0 15.0
N 0.63 0.84
P 1.55
-
All Dimensions in mm
PART
MARKING
SURFACE
1.90/2.10
Min/Max
0.63/0.84
0.27/0.48
1.05/1.25
Hall Sensor
PART
MARKING
SURFACE
123
Sensor Location
AH3782
Document number: DS38083 Rev. 1 - 2
11 of 14
www.diodes.com
September 2015
© Diodes Incorporated
11 Page | ||
| Páginas | Total 14 Páginas | |
| PDF Descargar | [ Datasheet AH3782.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| AH3781 | HIGH-VOLTAGE HIGH-SENSITIVITY HALL EFFECT LATCH | Diodes |
| AH3782 | HIGH-SENSITIVITY HALL EFFECT LATCH | Diodes |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |