|
|
Número de pieza | TDA21321 | |
Descripción | High-Performance DrBLADE | |
Fabricantes | Infineon | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de TDA21321 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! High-Performance DrBLADE
6.6 mm x 4.5 mm x 0.6 mm
TDA21321
Data Sheet
Revision 2.4, 2015-07-16
Power Management and Multi Market
1 page 3 Description
3.1 Pinout
TDA21321
Description
Figure 2 Pinout, Numbering and Name of Pins (transparent top view)
Table 2
Pin No.
2
3
4
5
7
8
9
33-38
(pads)
I/O Signals
Name
PWM
OFF#
IMON
IMONREF
TMON/FAULT
BOOT
PHASE
SW
Pin Type Buffer Type Function
I/O +3.3 V logic PWM drive logic input, Status output for VCIN
The tri-state PWM input is compatible with 3.3 V.
I +3.3 V logic Deactivates LS-MOSFET
Pull low to prevent LS-FET turn-on. Leave open if not used.
(If traced out in noisy layout it may require external pull up.)
O
Analog
Load current Sensing
Provides a voltage proportional to the high/low-side
MOSFET currents; Leave open if not used.
O
Analog
Load current Sensing
Reference to pin 4; Leave open if not used.
O
Analog/
Thermal Sensing / Fault Pin
Digital
Temperature reporting, fault signaling by logic “H”; Status
output of VDRV, Leave open if not used.
I
Analog
Bootstrap voltage pin
Connect to BOOT capacitor
I
Analog
Switch node input
Internally connected to SW pins, Connect to BOOT
capacitor as reference pin for boot voltage
O
Analog
Switch node output
High current output switching node
Data Sheet
5 Revision 2.4, 2015-07-16
5 Page TDA21321
Electrical Specification
Table 9
Voltage Supply And Biasing Current
Parameter Symbol
Values
Unit Note / Test Condition
UVLO VCIN
rising
VUVLO1_R
Min. Typ. Max.
3.0 – 4.0 V
UVLO VCIN VUVLO1_F
falling
2.6 – 3.6
Driver enable threshold; above threshold driver is active,
driver responds to PWM input when UVLO VDRV and
UVLO BOOT are enabled, TMON/FAULT reports driver
temperature when UVLO VDRV is enabled
Driver disable threshold; below threshold driver is inactive,
PWM and TMON/FAULT held low by pull-down resistors
UVLO VDRV VUVLO2_R
rising
4.16 4.25 4.34 V
GL, GH and TMON/FAULT enable threshold; when UVLO
VCIN is enabled then: above threshold GL is enabled, GH
depends on UVLO BOOT, TMON/FAULT is released to
report driver temperature
UVLO VDRV VUVLO2_F
falling
3.7 3.8 3.9
GL, GH and TMON/FAULT disable threshold; when UVLO
VCIN is enabled: below threshold after 3 consecutive cycles
or 15 µs (typ.) the driver outputs GL/GH are disabled,
TMON/FAULT stops temperature reporting and is held low
by pull-down resistor
UVLO BOOT VUVLOboot_R 3.88 4.05 4.22 V
rising
UVLO BOOT VUVLOboot_F 3.5 3.63 3.76
falling
Driver current IVDRV_600kHz – 18 – mA
IVDRV_1MHz
– 30
–
IC current
(control)
IVCIN_O
– 1.0 – mA
IC quiescent ICIN+IDRV
– 1.2 –
Pre-Bias at
SW
VSW_0
– 120 160 mV
VBOOT-VSW rising, GH enable threshold; when UVLO VCIN
and UVLO VDRV are active: above threshold GH responds
to PWM
VBOOT-VSW falling, GL/GH disable threshold; when UVLO
VCIN and UVLO VDRV are enabled: below threshold
counter starts, after 3 consecutive PWM cycles driver
outputs are disabled
OFF# = 3.3 V, fSW = 600 kHz
OFF# = 3.3 V, fSW = 1 MHz
OFF# = 3.3 V, PWM = Open for > 19 µs (typ.)
PWM in Tri-state (VPWM_S), VCIN = VDRV = 5V, internal pull-
down resistor 1.5 kΩ
Table 10 Current Sense
Parameter
Symbol
Values
Unit Note / Test Condition
IMON
Voltage Range
VIMON
IMONREF IMON gain resistor RIMON
range
Current sense gain aCS
Min. Typ. Max.
0.8 – 2.2 V IMONREF is a current mirror output serving
0.2 – 1.0 kΩ as unfiltered reference node. At IMON a
filtered voltage signal proportional to the
current is provided. It tracks the average
- 6.67 - µA/A value of IMONREF.
Leakage current ILeak
Current Zero current offset IOffset
Monitoring
Accuracy at 25 °C
… 125 °C
VDRV = 5 V ± 10 %
VCIN = 5 V ± 10 %
a11
a12
a13
a14
-2 0 2 µA ID = 0, VCM = 1.5, PWM in tri-state
-3 0 3 µA Corresponds to 2.25 mV at 5 mV/A
(RIMON = 750Ω), device in regulation
-3 – 3 % for 45 A < Iout < IOCPtrip tested at 25 A,
-2.5 – 2.5 % for 25 A ≤ Iout ≤ 45 A other guaranteed
-0.5 – 0.5 A for -25 < Iout < 25 A by design
-20 – 20 % for -50 A ≤ Iout ≤ -25 A
Data Sheet
11 Revision 2.4, 2015-07-16
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet TDA21321.PDF ] |
Número de pieza | Descripción | Fabricantes |
TDA21320 | High-Performance DrBLADE | Infineon |
TDA21321 | High-Performance DrBLADE | Infineon |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |