DataSheet.jp

STK433-060N-E の電気的特性と機能

STK433-060N-EのメーカーはON Semiconductorです、この部品の機能は「2ch class-AB Audio Power IC」です。


製品の詳細 ( Datasheet PDF )

部品番号 STK433-060N-E
部品説明 2ch class-AB Audio Power IC
メーカ ON Semiconductor
ロゴ ON Semiconductor ロゴ 




このページの下部にプレビューとSTK433-060N-Eダウンロード(pdfファイル)リンクがあります。

Total 11 pages

No Preview Available !

STK433-060N-E Datasheet, STK433-060N-E PDF,ピン配置, 機能
Ordering number : ENA2106A
STK433-060N-E
Thick-Film Hybrid IC
2ch class-AB Audio Power IC
50W+50W
http://onsemi.com
Overview
The STK433-060N-E is a hybrid IC designed to be used in 50W 2ch class AB audio power amplifiers.
Application
Audio Power amplifiers
Features
Pin-to-pin compatible outputs ranging from 40W to 150W.
Miniature package.
Output load impedance: RL = 6recommended.
Allowable load shorted time: 0.3 second
Allows the use of predesigned applications for standby and mute circuit.
Series model
STK433-040N-E
STK433-060N-E
STK433-130N-E
Output1 (10%/1kHz)
Output2 (0.4%/20Hz to 20kHz)
40W 2ch
25W 2ch
50W 2ch
35W 2ch
150W 2ch
100W 2ch
Max. rating VCC (quiescent)
Max. rating VCC (6)
Recommended operating VCC (6)
Dimensions (excluding pin height)
38V
46V
36V
40V
24V
27V
47.0mm25.6mm9.0mm
71.5V
63V
44V
67.0mm25.6mm9.0mm
Output1 (10%/1kHz)
Output2 (0.4%/20Hz to 20kHz)
Max. rating VCC (quiescent)
Max. rating VCC (6)
Recommended operating VCC (6)
Dimensions (excluding pin height)
STK433-330N-E
150W 3ch
100W 3ch
71.5V
63V
44V
64.0mm36.6mm9.0mm
STK433-840N-E
40W 4ch
25W 4ch
38V
36V
25V
64.0mm31.1mm9.0mm
STK433-890N-E
80W 4ch
50W 4ch
54V
47V
34V
78.0mm44.1mm9.0mm
Specifications
Absolute Maximum Ratings at Ta = 25C, Tc = 25C unless otherwise specified
Parameter
Symbol
Conditions
Maximum power supply voltage
Minimum operation supply voltage
#13 Operating voltage
*5
VCC max (0)
VCC max (1)
VCC max (2)
VCC min
VST OFF max
Non- signal
Signal, RL 6
Signal, RL 4
#13 voltage
Thermal resistance
j-c Per one power transistor
Junction temperature
Tj max
Should satisfy Tj max and Tc max
Operating substrate temperature
Tc max
Storage temperature
Tstg
Allowable time for load short-circuit
*4
ts
VCC = 27V, RL = 6, f = 50Hz
PO = 35W, 1ch drive
Ratings
46
40
33
10
-0.3 to +5.5
3.5
150
125
-30 to +125
0.3
Unit
V
V
V
V
V
C/W
C
C
C
s
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating
Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.
ORDERING INFORMATION
See detailed ordering and shipping information on page 11 of this data sheet.
Semiconductor Components Industries, LLC, 2013
April, 2013
41713HK/82912HKPC 018-11-0084 No.A2106-1/11

1 Page





STK433-060N-E pdf, ピン配列
Package Dimensions
unit : mm (typ)
47.0
41.2
STK433-060N-E
(R1.8)
9.0
1
3.6
2.0
(6.6) 14 2.0=28.0
15
0.5
RoHS directive pass
Equivalent Circuit
3
8
Pre Driver
CH1
11
12
1
2
SUB
9
0.4
2.9
5.5
Pre Driver
CH2
15
14
Stand-by Circuit
54 67
10 13
No.A2106-3/11


3Pages


STK433-060N-E 電子部品, 半導体
STK433-060N-E
Recommended external components
STK433-040N-E/060N-E/130N-E/330N-E
Parts
Location
R01, R23
Recommended
value
100/1W
Circuit purpose
Resistance for Ripple filter. (Fuse resistance is recommended.
Ripple filter is constituted with C03, C23.)
R02, R03, R04 1kResistance for input filters.
Above
Recommended value
Short-through current
may decrease at
high frequency.
-
Below
Recommended value
Short-through current
may increase at high
frequency.
-
R05, R06, R07
R08, R09, R10
56k
56k
Input impedance is determined.
Voltage Gain (VG) is determined with R11, R12, R13
Output neutral voltage(VN) shift.
(It is referred that R05=R08, R06=R09)
--
R11, R12, R13
1.8k
Voltage Gain (VG) is determined with R8, R9, R10
(As for VG, it is desirable to set up by R11, R12, R13)
It may oscillate.
(Vg < 30dB)
With especially no
problem
R14, R15, R16
4.7
Resistance for oscillation prevention.
--
R17, R18, R19
4.7/1W
Resistance for oscillation prevention.
--
R20, R21, R22
R30
C01, C02
C03, C23
C04, C05, C06
0.22/2W
(040N-E,060N-E)
0.22/5W
(130N-E,330N-E)
Note *5
100F/50V
100F/50V
2.2F/50V
This resistance is used as detection resistance of the protection
circuit application.
Decrease of
Maximum output
Power
It may cause thermal
runaway
Select Restriction resistance, for the impression voltage of ‘#17 (Stand-By) pin’ must not exceed the maximum
rating.
Capacitor for oscillation prevention.
Locate near the HIC as much as possible.
Power supply impedance is lowered and stable operation of
-
-
the IC is carried out. (Electrolytic capacitor is recommended.)
Decoupling capacitor
The change in the Ripple ingredient mixed in
The Ripple ingredient mixed in an input side Is removed from a an input side from a power supply line
power supply line. (Ripple filter is constituted with R01, R23.)
Input coupling capacitor.(for DC current prevention.)
-
C07, C08, C09
470pF
C10, C11, C12
3pF
Input filter capacitor
A high frequency noise is reduced with the filter constituted by
R02, R03, R04
Capacitor for oscillation prevention.
It may oscillate.
-
C13, C14, C15
10F/10V
Negative feedback capacitor.
The cutoff frequency of a low cycle changes.
(fL = 1/(2  C13 R11))
C16, C17, C18
0.1F
Capacitor for oscillation prevention.
The voltage gain (VG)
of low frequency is
extended. However,
the pop noise at the
time of a power
supply injection also
becomes large.
It may oscillate.
The voltage gain (VG)
of low frequency
decreases.
C19, C20, C21
100pF (040N-E)
56pF (060N-E)
N.C. (130N-E,
330N-E)
Capacitor for oscillation prevention.
It may oscillate.
L01, L02, L03
3H Coil for oscillation prevention.
With especially
no problem
It may oscillate.
No.A2106-6/11

6 Page



ページ 合計 : 11 ページ
 
PDF
ダウンロード
[ STK433-060N-E データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
STK433-060N-E

2-channel class-AB Audio Power IC

Sanyo Semicon Device
Sanyo Semicon Device
STK433-060N-E

2ch class-AB Audio Power IC

ON Semiconductor
ON Semiconductor


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap