|
|
Número de pieza | LA5724MC | |
Descripción | Separately-Excited Step-Down Switching Regulator | |
Fabricantes | ON Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de LA5724MC (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
No Preview Available ! Ordering number : ENA2021
LA5724MC
Monolithic Linear IC
Separately-Excited Step-Down
Switching Regulator
(Variable Type)
http://onsemi.com
Overview
The LA5724MC is a separately-excited step-down switching regulator (variable type).
Functions
• Time-base generator (160kHz) incorporated.
• Current limiter incorporated.
• Thermal shutdown circuit incorporated.
Specifications
Absolute Maximum Ratings at Ta = 25°C
Parameter
Symbol
Conditions
Ratings
Unit
Input voltage
SW pin application reverse voltage
VOS pin application voltage
Allowable power dissipation
VIN
VSW
VVOS
Pd max
Mounted on a circuit board.*
30
-1
-0.2 to 7
0.8
V
V
V
W
Operating temperature
Topr
-30 to +125
°C
Storage temperature
Tstg
-40 to +150
°C
Junction temperature
Tj max
150 °C
* Specified circuit board : 114.3×76.1×1.6mm3, glass epoxy board.
Caution 1) Absolute maximum ratings represent the value which cannot be exceeded for any length of time.
Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high current,
high voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details.
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating
Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.
Recommended Operating Conditions at Ta = 25°C
Parameter
Input voltage range
Symbol
VIN
Conditions
Ratings
4.5 to 28
Unit
V
Semiconductor Components Industries, LLC, 2013
August, 2013
32812 SY 20120207-S00001 No.A2021-1/6
1 page LA5724MC
Part selection and set
1. Resistors R1 and R2
R1 and R2 are resistors to set the output voltage. When the large resistance value is set, the error of set voltage increases
due to the VOS pin current. The output voltage may also increases due to the leak current of switching transistor at light
load. In consequence, it is essential to see R1 and R2 currents to around 500μA.
R1
=
1.23V
500μA
≈
2.4kΩ
2.0kΩ to 2.4kΩ recommended
R2 = (V1.O23UVT - 1) × R1
The calculation equation gives the output voltage set by R1 and R2.
VOUT = (1 + RR12) × 1.23V(typ)
2. Capacitor C1, C2 and C3
The large ripple current flows through C1 and C2, so that the high-frequency low-impedance product for switching
power supply must be used. Do not use, for C2, a capacitor eith extremely small equivalent series resistance (ESR),
such as ceramic capacitor, tantalum capacitor. Otherwise, the output waveform may develop abnormal oscillation. The
C2 capacitance and ESR value stabilization conditions are as follows:
1
2×π×C2×ESR
≤
20kHz
C3 is a capacitor for phase compensation of the feedback loop. Abnomal oscillation may occur when the C2
capacitance value is small or the equivalent series resistance is small. In this case, addition of the capacitance of C3
enable phase compensation, contributing to stabilization of power supply.
3. Input capacitor: Effecitive-value current
The AC ripple current flowing in the input capacitor is larger than that in the output capacitor. The equation expressing
the effective-value current is as folloes. Use the capacitor wiyhin the reted current range.
IC1 =
Vout
Vin
(Iout
2
(1
−
Vout
Vin
)
+
1
12
×
ΔIR
2
[Arms]
4. Output capacitor: Effective-value current
The AC ripple current flowing in the capacitor is the triangular wave. Therefore, its effective value is obtained from the
following equation. Select the output capacitor so that it does not exceed the allowable ripple current value.
IC2 =
1
23
VOUT(VIN-VOUT)
× L×fSW×VIN
[Arms]
fSW = switching frequency ··· 160kHz
5. Choke coil
Note that choke coil heating due to overload or load shorting may be a problem. The inductance valuecan be
determined from the following equation once the input voltage, output voltage, and current ripple conditions are known.
ΔIR indicates the ripple current value.
Reference example: VIN = 12V, VOUT = 5V, ΔIR = 150mA
L
=
VIN
-
VOUT
ΔIR
-
Vsat
×
Tom
=
12
-
5.0 -
0.15
0.4
×
2.8×10-6
≈ 120µH
Ton
=
(VIN
-
VOUT
-
T
Vsat)
/
(VOUT
+
VF)+1)
Toff = T - Ton
T: Switching repetition period ··· 6.25µs is assumed for the calculation
VF: Schottky diode forward voltage ··· 0.4V is assumed for the calculation
No.A2021-5/6
5 Page |
Páginas | Total 6 Páginas | |
PDF Descargar | [ Datasheet LA5724MC.PDF ] |
Número de pieza | Descripción | Fabricantes |
LA5724M | Monolithic Linear IC Separately-Excited Step-Down Switching Regulator | Sanyo Semicon Device |
LA5724MC | Separately-Excited Step-Down Switching Regulator | ON Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |