|
|
BLM18BB151SH1DのメーカーはMurataです、この部品の機能は「EMI Suppression Filters」です。 |
部品番号 | BLM18BB151SH1D |
| |
部品説明 | EMI Suppression Filters | ||
メーカ | Murata | ||
ロゴ | |||
このページの下部にプレビューとBLM18BB151SH1Dダウンロード(pdfファイル)リンクがあります。 Total 10 pages
Reference Only
Spec. No. JENF243A-9101J-01
Chip Ferrite Bead BLM18□□□□□□H1D
Murata Standard Specification[AEC-Q200]
P.1/10
1.Scope
This specification applies to Chip Ferrite Bead for Automotive Electronics BLM18_□H Series based on AEC-Q200.
2.Part Numbering
(ex.) BL M 18 AG 121 S H 1 D
(1) (2) (3) (4) (5) (6) (7) (8) (9)
(1)Product ID
(4)Characteristics
(7)Category(for Automotive Electronics)
(2)Type
(5)Typical Impedance at 100MHz (8)Numbers of Circuit
(3)Dimension (L×W) (6)Performance
(9)Packaging (D:Taping)
3.Rating
Customer
Part Number
MURATA
Part Number
Impedance ()
(at 100MHz)(*1)
(refer to below comment)
BLM18PG300SH1D
BLM18PG330SH1D
BLM18PG600SH1D
BLM18PG121SH1D
BLM18PG181SH1D
BLM18PG221SH1D
BLM18PG331SH1D
BLM18PG471SH1D
BLM18SN220TH1D
BLM18KG260TH1D
BLM18KG300TH1D
BLM18KG700TH1D
BLM18KG101TH1D
BLM18KG121TH1D
BLM18KG221SH1D
BLM18KG331SH1D
BLM18KG471SH1D
BLM18KG601SH1D
BLM18AG121SH1D
BLM18AG151SH1D
BLM18AG221SH1D
BLM18AG331SH1D
BLM18AG471SH1D
BLM18AG601SH1D
BLM18AG102SH1D
BLM18BB050SH1D
BLM18BA050SH1D
BLM18BB100SH1D
BLM18BA100SH1D
BLM18BB220SH1D
BLM18BA220SH1D
BLM18BB470SH1D
BLM18BD470SH1D
BLM18BA470SH1D
20 min.
33±25%
40 min.
120±25%
180±25%
220±25%
330±25%
470±25%
22±7
26±25%
30±25%
70±25%
100±25%
120±25%
220±25%
330±25%
470±25%
600±25%
120±25%
150±25%
220±25%
330±25%
470±25%
600±25%
1000±25%
5±25%
5±25%
10±25%
10±25%
22±25%
22±25%
47±25%
47±25%
47±25%
Typical
30
33
60
120
180
220
330
470
22
26
30
70
100
120
220
330
470
600
120
150
220
330
470
600
1000
5
5
10
10
22
22
47
47
47
DC Resistance
Rated
Current
(mA)
( max.) (*1)
(refer to below
comment)
Initial Values
ESD Rank
2:2kV
6:25kV
Values After
at 85℃ at 125℃
Testing
1000
3000*2 1000*2
0.05
0.025
0.10
0.050
500
2000*2 1000*2
1500*2 1000*2
1400*2 1000*2
1200*2 1000*2
0.1
0.05
0.09
0.10
0.15
0.2
0.10
0.18
0.14
0.20
6
1000
8000*2 5000*2
6000*2 2000*2
5000*2 2000*2
3500*2 1000*2
3000*2 1000*2
3000*2 1000*2
2200*2 1000*2
1700*2 1000*2
1500*2 1000*2
1300*2 1000*2
0.20
0.004
0.007
0.010
0.022
0.030
0.030
0.050
0.080
0.130
0.150
0.26
0.005
0.012
0.015
0.032
0.040
0.040
0.060
0.095
0.145
0.165
2
500 0.18 0.28
500 0.25 0.35
500 0.25 0.35
500
0.30 0.40
2
500 0.35 0.45
500 0.38 0.48
400 0.50 0.60
700 0.05 0.10
500 0.2 0.3
700 0.10 0.20
500 0.25 0.35
600
0.20 0.30
2
500 0.35 0.45
550 0.25 0.35
500 0.3 0.4
300 0.55 0.65
MURATA MFG.CO., LTD.
1 Page Spec. No. JENF243A-9101J-01
5.Marking
No marking.
Reference Only
P.3/10
6.Specifications
6-1.Electrical Performance
No. Item
Specification
6-1-1 Impedance
Meet item 3.
6-1-2 DC Resistance
Meet item 3.
Test Method
Measuring Frequency : 100MHz±1MHz
Measuring Equipment : Agilent 4291A or the equivalent
Test Fixture : Agilent 16192A or the equivalent
Measuring Equipment : Digital multi meter
For BLM18SN
Measuring Equipment : YOKOGAWA 755611 or the equivalent
Test Fixture : Agilent 16044A or the equivalent
*Except resistance of the Substrate and Wire
6-2. Mechanical Performance(based on Table 13 for FILTER EMI SUPPRESSORS/FILTERS)
AEC-Q200 Rev.D issued June. 1 2010
AEC-Q200
No. Stress
Test Method
Murata Specification / Deviation
3 High
Temperature
Exposure
1000hours at 125 deg C
Set for 24hours at room
temperature, then measured.
Meet Table A after testing.
Table A
Appearance
No damage
Impedance
Within ±30%
Change
(for BLM18KG/SN
(at 100MHz)
Within ±50%)
DC
Resistance
Meet item 3.
4 Temperature Cycling 1000cycles
Meet Table B after testing.
-55 deg C to +125 deg C
TableB
Set for 24hours at room
temperature, then measured.
Appearance
Impedance
Change
(at 100MHz)
No damage
Within ±30%
(for BLM18SN
Within ±50%)
(for BLM18KG
Within-10%to+50%)
DC Resistance Meet item 3.
5 Destructive
Per EIA469
Physical Analysis
No electrical tests
No defects
7 Biased Humidity
1000hours at 85 deg C, 85%RH Meet Table A after testing.
Apply max rated current.
8 Operational Life
Apply 125 deg C 1000hours
Set for 24hours at room
temperature, then measured
Meet Table A after testing.
If the rated current of parts exceed 1A,
the operating temperature should be 85 deg C.
9 External Visual
Visual inspection
No abnormalities
10
Physical Dimension
Meet ITEM 4
No defects
(Style and Dimensions)
12 Resistance to Solvents Per MIL-STD-202
Method 215
Not Applicable
MURATA MFG.CO., LTD.
3Pages Spec. No. JENF243A-9101J-01
7-4. Specification of Outer Case
Reference Only
P.6/10
H
W
Label
Outer Case Dimensions
(mm)
WD H
Standard Reel Quantity in Outer Case
(Reel)
D
186 186
93
5
Above Outer Case size is typical. It depends on a quantity of an
order.
8. ! Caution
8-1.Rating
Do not use products beyond the Operating Temperature Range and Rated Current.
8-2.Surge current
Excessive surge current (pulse current or rush current) than specified rated current applied to the product
may cause a critical failure, such as an open circuit, burnout caused by excessive temperature rise.
Please contact us in advance in case of applying the surge current.
8-3.Fail Safe
Be sure to provide an appropriate fail-safe function on your product to prevent from a second damage
that may be caused by the abnormal function or the failure of our products.
8-4.Limitation of Applications
Please contact us before using our products for the applications listed below which require especially high
reliability for the prevention of defects which might directly cause damage to the third party's life, body or property.
(1)Aircraft equipment
(6)Disaster prevention / crime prevention equipment
(2)Aerospace equipment
(7)Traffic signal equipment
(3)Undersea equipment
(8)Transportation equipment (trains,ships,etc.)
(4)Power plant control equipment (9)Applications of similar complexity and /or reliability requirements
(5)Medical equipment
to the applications listed in the above
9. Notice
This product is designed for solder mounting.
Please consult us in advance for applying other mounting method such as conductive adhesive.
9-1.Land pattern designing
Standard land dimensions
< For BLM18 series (except BLM18PG/KG/SN type) >
Chip Ferrite Bead
Type
Soldering a
BLM18
Flow
c
(except
Reflow 0.7
18PG/KG/SN type)
a Solder Resist
b Pattern
b
2.2 to 2.6
1.8 to 2.0
c
0.7
(in mm)
MURATA MFG.CO., LTD.
6 Page | |||
ページ | 合計 : 10 ページ | ||
|
PDF ダウンロード | [ BLM18BB151SH1D データシート.PDF ] |
データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。 |
部品番号 | 部品説明 | メーカ |
BLM18BB151SH1D | EMI Suppression Filters | Murata |