BD1HC500EFJ-C Datasheet PDF - ROHM Semiconductor
| Part Number | BD1HC500EFJ-C | |
| Description | 1ch High-side switch | |
| Manufacturers | ROHM Semiconductor | |
| Logo |  |
|
|
There is a preview and BD1HC500EFJ-C download ( pdf file ) link at the bottom of this page. Total 21 Pages | ||
Preview 1 page No Preview Available !
Datasheet
Automotive IPS series
1ch High-side switch
BD1Hx500 Series
Features
■ Built-in overcurrent protection circuit
■ Built-in Thermal Shut Down(TSD)
■ Built-in Open Load Detection circuit(When Output is
OFF)
■ Possibility to control directly from CMOS logic IC
■ Low standby current
■ Built-in Under Voltage Lock Out circuit
■ Built-in diagnostic(ST) output function
■ Low On resistance of RDS(ON)=500mΩ(Typ) (VDD=12V,
Ta=25°C, Io=0.25A)
■ Monolithic power IC that has a built in control part
(CMOS) and a power MOS FET on 1chip
■ 1ch High-side switch for the mechanical relay coil
drive
■ AEC-Q100 qualified (1)
(1) Grade 1
General Description
BD1HC/D500 Series is an Automotive 1ch High-Side
switch.
It has a built-in overcurrent protection circuit, Thermal
Shut Down (TSD) circuit, Open Load Detection circuit,
Under Voltage Lock Out circuit, and has diagnostic (ST)
output function at the time during abnormal detection.
Application
■ For automotive (Air conditioner, body equipment, and
meter, etc.)
Typical Application Circuit
Product Summary
Operating voltage
On-state resistance
(25°C, Typ)
Overcurrent limit (Typ)
Active clamp energy (25°C)
4V to 18V
500mΩ
1.45A
33mJ
Package
HTSOP-J8
HSON8
MSOP8
4.90mm x 6.00mm x 1.00mm
2.90mm x 3.00mm x 0.60mm
2.90mm x 4.00mm x 0.90mm
HTSOP-J8
HSON 8
MSOP 8
○Product structure：Silicon monolithic integrated circuit
www.rohm.com
© 2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・14・001
○This product is not designed protection against radioactive rays
1/18
TSZ02201-0G3G0BD00070-1-2
2015.04.15 Rev.002
|
| |
 
BD1Hx500 Series
Datasheet
Electrical Characteristics (unless otherwise specified, VDD=4V to 18V, -40°C ≤ Tj ≤ 150°C)
Parameter
Symbol
Target value
Min Typ
Max
Unit
[Protect Circuit]
Conditions
Overcurrent protection
ILIM
Diagnostic output
delay time(OCP)
ON
OFF
Open Load Detection threshold
(1)
Open Load Detection delay time
tDHL
tDLH
VOPEN
TOPEN
0.8
-
-
1.3
100
1.45
20
100
2.8
300
2.0
100
200
4.0
1000
A
μs
Diagnostic output
delay time(OCP) Figure20
μs
VDD=12V, RL=∞ to 4Ω
Figure 20
V VIN =0V
μs VIN =5V to 0V Figure21
(1) In order to detect the voltage, an external resistance (Rext) of 130kΩ (Typ) is required between VDD and OUT pins.
At worst condition, the following resistance is recommended.
VDD
12 V
6V
5V
Rext
Under 200kΩ
Under 50kΩ
Under 25kΩ
5V
100kΩ
VDD=12V
ST VDD
130kΩ
IN OUT
GND
Rext
Terms
Figure 1. Terms
www.rohm.com
© 2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
5/18
TSZ02201-0G3G0BD00070-1-2
2015.04.15 Rev.002
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for BD1HC500EFJ-C electronic component. |
| Information | Total 21 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ BD1HC500EFJ-C.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| BD1HC500EFJ-C | The function is 1ch High-side switch. ROHM Semiconductor | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
BD1H
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||