DataSheet.jp

MSL0201RGB の電気的特性と機能

MSL0201RGBのメーカーはROHM Semiconductorです、この部品の機能は「PICOLED-RGB-side」です。


製品の詳細 ( Datasheet PDF )

部品番号 MSL0201RGB
部品説明 PICOLED-RGB-side
メーカ ROHM Semiconductor
ロゴ ROHM Semiconductor ロゴ 




このページの下部にプレビューとMSL0201RGBダウンロード(pdfファイル)リンクがあります。

Total 8 pages

No Preview Available !

MSL0201RGB Datasheet, MSL0201RGB PDF,ピン配置, 機能
MSL0201RGB
PICOLEDTM-RGB-side
lFeatures
Side view RGB LEDs
Ultra compact, thin size
lSize
1030061(30(410125)0)
1.03×.005.6×m1m.3m(t=m0(.t2=m0.m43) mm)
lDimensions
lOutline
Data Sheet
Color
Type
R
GB
lRecommended Solder Pattern
Tolerance : 0.1
(unit : mm)
(unit : mm)
lSpecifications
Part No.
MSL0201RGB
Chip Emitting
Structure Color
AIGaInP Red
Green
InGaN
Blue
Absolute Maximum Ratings (Ta=25ºC)
Forward Peak Forward Reverse
Operating Temp. Storage Temp.
Current Current Voltage
IF(mA) IFP(mA) VR(V)
Topr(ºC)
Tstg(ºC)
20 100*1 5 -40 to +85 -40 to +100
Electrical and Optical Characteristics (Ta=25ºC)
Forward Voltag VF Reverse Current IR Dominant Wavelength lD Luminous Intensity IV
Typ. IF Max. VR Min.*2 Typ. Max.*2 IF Min. Typ. IF
(V) (mA) (mA) (V) (nm) (nm) (nm) (mA) (mcd) (mcd) (mA)
2.1
618 624 630
11 25
3.0 5 100 5 519 527 536 5 56 90 5
2.9
464 470 476
11 22
*1: Duty1/20, 1kHz *2 : Reference
www.rohm.com
© 2015 ROHM Co., Ltd. All rights reserved.
1/7
2015.03 - Rev.B

1 Page





MSL0201RGB pdf, ピン配列
MSL0201RGB
lViewing Angle
SCANNING ANGLE (deg)
Scanning
Direction
MSL0201RGB (R)
MSL0201RGB (G)
MSL0201RGB (B)
Data Sheet
SCANNING ANGLE (deg)
Scanning
Direction
MSL0201RGB (R)
MSL0201RGB (G)
MSL0201RGB (B)
RELATIVE INTENSITY
lSpectrum Data
RELATIVE INTENSITY
1 IF=20mA
MSL0201RGB (R)
MSL0201RGB (G)
0.8 MSL0201RGB (B)
0.6
0.4
0.2
0
380 480 580 680 780
WAVELENGTH [nm]
* Please take this data as a reference data for the samples are measured randomly.
* The data is relativized for each color. It is NOT to show the spectrum peaks are equal.
lRank Reference of Brightness
Triple Color
Emitting
Color
Rank
sigh
Blue
MSL0201RGB
Green
Red
1234
11 to 22 22 to 45 11 to 22 22 to 45
56 to 90
56 to 90
11 to 22
Unit (mcd) (Ta=25ºC, IF5mA)
5678
11 to 22 22 to 45 11 to 22 22 to 45
56 to 90
56 to 90
22 to 45
*Measurement tolelrance 10%
 
www.rohm.com
© 2015 ROHM Co., Ltd. All rights reserved.
3/7
2015.03 - Rev.B


3Pages


MSL0201RGB 電子部品, 半導体
MSL0201RGB
Data Sheet
3. Others
3-1. Surrounding Gas
Notice that if it is stored under the condition of acid gas (chlorine gas, sulfured gas) or alkali gas (ammonia), it
may result in low soldering ability (caused by the change in quality of the plating surface ) or optical
characteristics changes (light intensity, chrominance) and change in quality of die bonding (Ag-paste) materials.
All of the above will cause function failure of the products.
Therefore, please pay attention to the storage environment for mounted product (concern the generated gas of
the surrounding parts of the products and the atmospheric environment).
3-2. Electrostatic Damage
The product is part of semiconductor and electrostatic sensitive, there’s high possibility to be damaged by the
electrostatic discharge. Please take appropriate measures to avoid the static electricity from human body and
earthing of production equipment. The resistance values of electrostatic discharge (actual values) vary with
products, therefore, please call our Sales staffs for inquiries.
3-3. Electromagnetic Wave
Please concern the influence on LED in case of application with strong electromagnetic wave such as IH
(Induction heating).
4.Mounting
4-1. Soldering
•No resin hardening agent such as filler is used in the sealing resin of the product. Therefore, resin expansion
and
moisture absorption at humidity will cause heat stress during soldering process and finally has bad influence on
the product’s reliability.
•The product is not for flow soldering.
•Do not expose the product in the environment of high temperature (over 100ºC) or rapid temperature shift
(within 3ºC of temperature gradient) during the flow soldering of surrounding parts.
•Please set appropriate reflow temperature based on our product usage conditions and specification.
•The max for reflowing is 2 times, please finish the second flow soldering and flow soldering with other parts
within the usage limitation after open the moistureproof package.
•Compare with N2 reflow, during air reflow, because of the heat and surrounding conditions, it may cause the
discoloration of the resin.
•For our product that has no solder resist, because of its solder amount and soldering conditions, one of its
specific characteristics is that solder will penetrate into LED. Thus, there's high possibility that will influence its
reliability. Therefore, please be informed, concerning it before using it.
4-2. Automatic Mounting
4-2-1.Silicon Resin Sealing Product
The sealing resin of LED is very soft, so please select adsorption nozzle that would not apply stress directly
on the sealing section.
4-2-2.Mini Package (Smaller than 1608 size)
Vibration may result in low mounting rate since it will cause the static electricity of product and adhere to top
cover tape. We recommend to
•set magnet on parts feeder cassette of the mounter to control the product stabilization
•set ionizer to prevent electrostatic charge
4-3. Mounting Location
The stress like bending stress of circuit board dividing after mounting, may cause LED package crack or
damage of LED internal junction, therefore, please concern the mounting direction and position to avoid bending
or screwing with great stress of the circuit board.
www.rohm.com
© 2015 ROHM Co., Ltd. All rights reserved.
6/7
2015.03 - Rev.B

6 Page



ページ 合計 : 8 ページ
 
PDF
ダウンロード
[ MSL0201RGB データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
MSL0201RGB

PICOLED-RGB-side

ROHM Semiconductor
ROHM Semiconductor


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap