|
|
HCPL-J454のメーカーはAVAGOです、この部品の機能は「High Speed Optocouplers」です。 |
部品番号 | HCPL-J454 |
| |
部品説明 | High Speed Optocouplers | ||
メーカ | AVAGO | ||
ロゴ | |||
このページの下部にプレビューとHCPL-J454ダウンロード(pdfファイル)リンクがあります。 Total 19 pages
HCPL-4504/J454/0454, HCNW4504
High CMR, High Speed Optocouplers
Data Sheet
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
Description
The HCPL-4504 and HCPL-0454 contain a GaAsP LED
while the HCPL-J454 and HCNW4504 contain an AlGaAs
LED. The LED is optically coupled to an integrated high
gain photo detector.
The HCPL-4504 series has short propagation delays and
high CTR. The HCPL-4504 series also has a guaranteed
propagation delay difference (tPLH-tPHL). These features
make the HCPL-4504 series an excellent solution to IPM
inverter dead time and other switching problems. The
CTR, propagation delay, and CMR are specified both for
TTL and IPM conditions which are provided for ease of
application. These single channel, diode-transistor opto-
couplers are available in 8-Pin DIP, SO-8, and Widebody
package configurations. An insulating layer between a
LED and an integrated photodetector provide electrical
insulation between input and output. Separate connec-
tions for the photodiode bias and output-transistor col-
lector increase the speed up to a hundred times that of
a conventional phototransistor coupler by reducing the
base collector capacitance.
Functional Diagram
NC 1
ANODE 2
CATHODE 3
NC 4
8 VCC
7 NC
6 VO
5 GND
TRUTH TABLE
LED
ON
OFF
VO
LOW
HIGH
A 0.1 μF bypass capacitor between pins 5 and 8 is recommended.
Schematic
ICC 8
VCC
+
ANODE
2
VF
–
CATHODE
3
IF
SHIELD
IO 6
VO
5
GND
Features
• Short propagation delays for TTL and IPM applications
• 15 kV/μs minimum Common Mode Transient immu-
nity at VCM = 1500 V for TTL/load drive
• High CTR at TA = 25°C
>25% for HCPL-4504/0454
>23% for HCNW4504
>19% for HCPL-J454
• Electrical specifications for common IPM applications
• TTL compatible
• Open collector output
• Safety approval:
UL recognized
– 3750 V rms/1min. for HCPL-4504/0454/J454
– 5000 V rms/1min. for HCPL-4504 Option 020 and
HCNW4504
CSA approved
IEC/EN/DIN EN 60747-5-2 approved
– VIORM = 560 Vpeak for HCPL-0454 Option 060
– VIORM = 630 Vpeak for HCPL-4504 Option 060
– VIORM = 891 Vpeak for HCPL-J454
– VIORM = 1414 Vpeak for HCNW4504
Applications
• Inverter circuits and Intelligent Power Module (IPM)
interfacing: High Common Mode Transient immunity
(> 10 kV/μs for an IPM load/drive) and (tPLH - tPHL)
Specified (see Power Inverter Dead Time section)
• Line receivers: Short propagation delays and low in-
put-output capacitance
• High speed logic ground isolation: TTL/TTL, TTL/
CMOS, TTL/LSTTL
• Replaces pulse transformers: Save board space and
weight
• Analog signal ground isolation: Integrated photode-
tector provides improved linearity over phototransis-
tors
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.
1 Page Package Outline Drawings
HCPL-4504 Outline Drawing
TYPE NUMBER
1.19 (0.047) MAX.
9.65 ± 0.25
(0.380 ± 0.010)
87
65
A XXXXZ
YYWW RU
12 34
OPTION CODE*
DATE CODE
UL
RECOGNITION
1.78 (0.070) MAX.
3.56 ± 0.13
(0.140 ± 0.005)
4.70 (0.185) MAX.
7.62 ± 0.25
(0.300 ± 0.010)
6.35 ± 0.25
(0.250 ± 0.010)
5° TYP.
0.254
+
-
0.076
0.051
(0.010+-
0.003)
0.002)
0.51 (0.020) MIN.
2.92 (0.115) MIN.
1.080 ± 0.320
(0.043 ± 0.013)
0.65 (0.025) MAX.
2.54 ± 0.25
(0.100 ± 0.010)
DIMENSIONS IN MILLIMETERS AND (INCHES).
* MARKING CODE LETTER FOR OPTION NUMBERS
"L" = OPTION 020
"V" = OPTION 060
OPTION NUMBERS 300 AND 500 NOT MARKED.
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
HCPL-4504 Gull Wing Surface Mount Option 300 Outline Drawing
9.65 ± 0.25
(0.380 ± 0.010)
87
65
LAND PATTERN RECOMMENDATION
1.016 (0.040)
6.350 ± 0.25
(0.250 ± 0.010)
10.9 (0.430)
12
34
1.19
(0.047)
MAX.
1.780
(0.070)
MAX.
3.56 ± 0.13
(0.140 ± 0.005)
1.27 (0.050)
9.65 ± 0.25
(0.380 ± 0.010)
7.62 ± 0.25
(0.300 ± 0.010)
2.0 (0.080)
0.254
+
-
0.076
0.051
(0.010+-
0.003)
0.002)
1.080 ± 0.320
(0.043 ± 0.013)
2.54
(0.100)
BSC
0.635 ± 0.130
(0.025 ± 0.005)
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
0.635 ± 0.25
(0.025 ± 0.010)
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
12° NOM.
3
3Pages HCNW4504 Outline Drawing (8-Pin Widebody Package)
11.15 ± 0.15
(0.442 ± 0.006)
87 6 5
A
HCNWXXXX
YYWW
1234
TYPE NUMBER
DATE CODE
1.55
(0.061)
MAX.
11.00
(0.433)
MAX.
9.00 ± 0.15
(0.354 ± 0.006)
10.16 (0.400)
TYP.
7° TYP.
(05..21001)MAX.
0.254
+ 0.076
- 0.0051
(0.010+-
0.003)
0.002)
2.54 (0.100)
TYP.
1.78 ± 0.15
(0.070 ± 0.006)
3.10 (0.122)
3.90 (0.154)
0.51 (0.021) MIN.
0.40 (0.016)
0.56 (0.022)
DIMENSIONS IN MILLIMETERS (INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
HCNW4504 Gull Wing Surface Mount Option 300 Outline Drawing
11.15 ± 0.15
(0.442 ± 0.006)
87
65
LAND PATTERN RECOMMENDATION
9.00 ± 0.15
(0.354 ± 0.006)
1234
1.55
(0.061)
MAX.
(04..10508)MAX.
13.56
(0.534)
1.3
(0.051)
2.29
(0.09)
12.30 ± 0.30
(0.484 ± 0.012)
11.00 MAX.
(0.433)
1.78 ± 0.15
(0.070 ± 0.006)
2.54
(0.100)
BSC
0.75 ± 0.25
(0.030 ± 0.010)
1.00 ± 0.15
(0.039 ± 0.006)
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
0.254
+ 0.076
- 0.0051
(0.010+-
0.003)
0.002)
7° NOM.
6
6 Page | |||
ページ | 合計 : 19 ページ | ||
|
PDF ダウンロード | [ HCPL-J454 データシート.PDF ] |
データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。 |
部品番号 | 部品説明 | メーカ |
HCPL-J454 | High CMR / High Speed Optocouplers | Hewlett-Packard |
HCPL-J454 | High Speed Optocouplers | AVAGO |
HCPL-J456 | Intelligent Power Module and Gate Drive Interface Optocouplers | Avago |