DataSheet.jp

K3HB-P の電気的特性と機能

K3HB-PのメーカーはOmronです、この部品の機能は「Timer Interval Indicator」です。


製品の詳細 ( Datasheet PDF )

部品番号 K3HB-P
部品説明 Timer Interval Indicator
メーカ Omron
ロゴ Omron ロゴ 




このページの下部にプレビューとK3HB-Pダウンロード(pdfファイル)リンクがあります。

Total 5 pages

No Preview Available !

K3HB-P Datasheet, K3HB-P PDF,ピン配置, 機能
Timer Interval Indicator
K3HB-P
Digital Time Interval Meter for Measuring
Passing Speed, Time, or Cycle between Two
Points.
• Measures Wide Range of Pulse Interval Times
Measures, calculates, and displays pulse intervals between two
points. Wide range for pulse interval measurements, from 10 ms to
3,200 s, max.
• Six Measurement Operations, Including Passing Speed, Time,
and Cycle Measurement between Two Points
One Digital Time Interval Meter has six measurement functions, to
support a variety of pulse interval measurement applications. Select
the best function for your application from the following: Passing
speed, cycle, time difference, time band, measuring length, and
interval.
Refer to Common Precautions on page 30.
Model Number Structure
Model Number Legend
Base Units and Optional Boards can be ordered individually or as sets.
Base Units
Base Units with Optional Boards
K3HB-P @
K3HB-P@-@@@
15
1 234 5
1. Input Sensor Codes
NB: NPN input/voltage pulse input
PB: PNP input
5. Supply Voltage
100-240 VAC: 100 to 240 VAC
24 VAC/VDC: 24 VAC/VDC
Optional Board
Sensor Power Supply/Output Boards
K33-@
2
Relay/Transistor Output Boards
K34-@
3
Event Input Boards
K35-@
4
2. Sensor Power Supply/Output Type Codes
None: None
CPA: Relay output (PASS: SPDT) + Sensor power supply
(12 VDC±10%, 80 mA) (See note 1.)
L1A: Linear current output (DC0(4)-20 mA) + Sensor power supply
(12 VDC±10%, 80 mA) (See note 2.)
L2A: Linear voltage output (DC0(1)-5 V, 0 to 10 V) + Sensor power supply
(12 VDC±10%, 80 mA) (See note 2.)
A: Sensor power supply (12 VDC ±10%, 80 mA)
FLK1A: Communications (RS-232C) + Sensor power supply
(12 VDC±10%, 80 mA) (See note 2.)
FLK3A: Communications (RS-485) + Sensor power supply
(12 VDC±10%, 80 mA) (See note 2.)
3. Relay/Transistor Output Type Codes
None: None
C1: Relay contact (H/L: SPDT each)
C2: Relay contact (HH/H/LL/L: SPST-NO each)
T1: Transistor (NPN open collector: HH/H/PASS/L/LL)
T2: Transistor (PNP open collector: HH/H/PASS/L/LL)
BCD: BCD output + transistor output (NPN open collector: HH/H/PASS/L/LL)
DRT: DeviceNet (See note 2.)
4. Event input Type Codes
None: None
1: 5 points (M3 terminal blocks) NPN open collector
2: 8 points (10-pin MIL connector) NPN open collector
3: 5 points (M3 terminal blocks) PNP open collector
4: 8 points (10-pin MIL connector) PNP open collector
Note: 1. CPA can be combined with relay outputs only.
2. Only one of the following can be used by each Digital Indicator:
RS-232C/RS-485 communications, a linear output, or DeviceNet communications.
Accessories (Sold Separately)
K32-DICN: Special Cable (for event inputs with 8-pin connector)
K32-BCD: Special BCD Output Cable
10 Timer Interval Indicator K3HB-P

1 Page





K3HB-P pdf, ピン配列
Characteristics
Display range
Measurement accuracy
(at 23±5°C)
Measurement range
Input signals
19,999 to 99,999
±0.08% rgd ±1 digit (for voltage pulse/open collector sensors)
Functions F1, F3, and F4:10 ms to 3,200 s
Function F2:
20 ms to 3,200 s
Functions F5 and F6: 0 to 4 gigacounts
No-voltage contact (30 Hz max. with ON/OFF pulse width of 15 ms min.)
Mode Input frequency ON/OFF ON voltage OFF voltage
Input
range
pulse width
impedance
F1 to F4 0 to 50 kHz
9 µs min.
4.5 to 30 V 30 to 2 V 10 k
F5, F6 0 to 30 kHz
16 µs min.
Mode Input frequency ON/OFF
range
pulse width
F1 to F4 0 to 50 kHz
9 µs min.
F5, F6 0 to 30 kHz
16 µs min.
Note: The Digital Time Interval Meter
will malfunction if a pulse greater
than the input frequency range is
input. SYSERR may appear on
the display.
Voltage pulse
Opencollector
Connectable sensors
Comparative output response
time (transistor output)
Linear output response time
Insulation resistance
Dielectric strength
Noise immunity
Vibration resistance
Shock resistance
Weight
Degree of
protection
Front panel
Rear case
Terminals
Memory protection
Applicable standards
EMC
ON residual voltage: 3 V max.
OFF leakage current: 1.5 mA max.
Load current:
Must have a switching capacity of 20 mA or higher.
Must be able to properly switch load currents of 5 mA or less.
2 ms max. (time until the comparative output is made when there is a forced sudden change in the input signal
from 15% to 95% or 95% to 15%)
10 ms max. (time until the final analog output value is reached when there is a forced sudden change in the
input signal from 15% to 95% or 95% to 15%)
20 Mmin. (at 500 VDC)
2,300 VAC for 1 min between external terminals and case
100 to 240 VAC models:
±1,500 V at power supply terminals in normal or common mode
(waveform with 1-ns rising edge and pulse width of 1 µs/100 ns)
24 VAC/VDC models:
±1,500 V at power supply terminals in normal or common mode
(waveform with 1-ns rising edge and pulse width of 1 µs/100 ns)
Frequency: 10 to 55 Hz; Acceleration: 50 m/s2, 10 sweeps of 5 min each in X, Y, and Z directions
150 m/s2 (100 m/s2 for relay outputs) 3 times each in 3 axes, 6 directions
Approx. 300 g (Base Unit only)
Conforms to NEMA 4X for indoor use (equivalent to IP66)
IP20
IP00 + finger protection (VDE0106/100)
EEPROM (non-volatile memory)
Number of rewrites: 100,000
UL61010C-1, CSA C22.2 No. 1010.1 (evaluated by UL)
EN61010-1 (IEC61010-1): Pollution degree 2/Overvoltage category II
EN61326: 1997, A1: 1998, A2: 2001
EMI: EN61326+A1 industrial applications
Electromagnetic radiation interference
CISPR 11 Group 1, Class A: CISPRL16-1/-2
Terminal interference voltage
CISPR 11 Group 1, Class A: CISPRL16-1/-2
EMS: EN61326+A1 industrial applications
Electrostatic Discharge Immunity
EN61000-4-2: 4 kV (contact), 8 kV (in air)
Radiated Electromagnetic Field Immunity
EN61000-4-3: 10 V/m 1 kHz sine wave amplitude modulation (80 MHz to 1 GHz, 1.4GHz to 2 GHz)
Electrical Fast Transient/Burst Immunity
EN61000-4-4: 2 kV (power line), 1 kV (I/O signal line)
Surge Immunity
EN61000-4-5: 1 kV with line (power line), 2 kV with ground (power line)
Conducted Disturbance Immunity
EN61000-4-6: 3 V (0.15 to 80 MHz)
Power Frequency Magnetic Immunity
EN61000-4-8: 30 A/m (50 Hz) continuous time
Voltage Dips and Interruptions Immunity
EN61000-4-11: 0.5 cycle, 0°/180°, 100% (rated voltage)
12 Timer Interval Indicator K3HB-P


3Pages





ページ 合計 : 5 ページ
 
PDF
ダウンロード
[ K3HB-P データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
K3HB-C

Digital Indicators User Manual

Omron
Omron
K3HB-C

Up/Down Counting Pulse Indicator

Omron
Omron
K3HB-H

Temperature Indicator

Omron
Omron
K3HB-P

Digital Indicators User Manual

Omron
Omron


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap