DataSheet.jp

ISL80015A の電気的特性と機能

ISL80015AのメーカーはIntersil Corporationです、この部品の機能は「Compact Synchronous Buck Converters」です。


製品の詳細 ( Datasheet PDF )

部品番号 ISL80015A
部品説明 Compact Synchronous Buck Converters
メーカ Intersil Corporation
ロゴ Intersil Corporation ロゴ 




このページの下部にプレビューとISL80015Aダウンロード(pdfファイル)リンクがあります。

Total 16 pages

No Preview Available !

ISL80015A Datasheet, ISL80015A PDF,ピン配置, 機能
DATASHEET
Compact Synchronous Buck Converters
ISL80020, ISL80020A, ISL80015, ISL80015A
The ISL80020, ISL80020A, ISL80015 and ISL80015A are highly
efficient, monolithic, synchronous step-down DC/DC converters
that can deliver up to 2A of continuous output current from a 2.7V
to 5.5V input supply. They use peak current mode control
architecture to allow very low duty cycle operation. They operate
at either 1MHz or 2MHz switching frequency, thereby providing
superior transient response and allowing for the use of small
inductors. They have excellent stability.
Features
• VIN range 2.7V to 5.5V
• IOUT maximum is 1.5A or 2A (see Table 1 on page 2)
• Switching frequency is 1MHz or 2MHz (see Table 1 on page 2)
• Overcurrent and short circuit protection
• Over-temperature/thermal protection
The ISL80020, ISL80020A, ISL80015 and ISL80015A integrate
very low rDS(ON) MOSFETs in order to maximize efficiency. In
addition, since the high-side MOSFET is a PMOS, the need for a
Boot capacitor is eliminated, thereby reducing external
component count. They can operate at 100% duty cycle
(at 1MHz).
The device is configured in PWM (pulse width modulation) for
fast transient response, which helps reduce the output noise
and RF interference.
• Negative current protection
• Power-good and enable
• 100% duty cycle (1MHZ)
• Internal soft-start and soft-stop
• VIN undervoltage lockout and VOUT overvoltage protection
• Up to 95% peak efficiency
Applications
These devices are offered in a space saving 8 pin 2mmx2mm
TDFN lead free package with exposed pad for improved thermal
performance. The complete converter occupies less than
64mm2 area.
• General purpose POL
• Industrial, instrumentation, and medical equipment
• Telecom and networking equipment
• Game console
VIN
GND
EN
PG
+2.7V...+5.5V
C1
22µF
1 VIN
2 EN
ISL80015, ISL80020
3 SGND
4 PG
EPAD
9
L1
PHASE 8
PGND 7
+1.8V/2A
C2
22µF
NC 6
FB 5
0.6V
C3
22pF
R1
200kΩ 1%
R2
100kΩ 1%
VOUT
GND
R1
=
R2
V---V--F--O--B---
1
(EQ. 1)
FIGURE 1. TYPICAL APPLICATION CIRCUIT CONFIGURATION
100
90
80
70
2.5VOUT
1.5VOUT
1.8VOUT
3.3VOUT
60
50
400.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
OUTPUT LOAD (A)
FIGURE 2. EFFICIENCY vs LOAD, fSW = 2MHz, VIN = 5V, TA = +25°C
February 17, 2015
FN6692.1
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC 2015. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.

1 Page





ISL80015A pdf, ピン配列
ISL80020, ISL80020A, ISL80015, ISL80015A
Pin Configuration
ISL80020, ISL80020A, ISL80015, ISL80015A
(8 LD 2x2 TDFN)
TOP VIEW
VIN 1
EN 2
SGND 3
PG 4
EPAD
(GPAND)
PIN 9
8 PHASE
7 PGND
6 NC
5 FB
Pin Descriptions
PIN #
1
2
3
4
5
6
7
8
9
PIN NAME
VIN
EN
SGND
PG
FB
NC
PGND
PHASE
E PAD
PIN DESCRIPTION
The input supply for the power stage of the PWM regulator and the source for the internal linear regulator that provides
bias for the IC. Place a minimum of 10µF ceramic capacitance from VIN to GND and as close as possible to the IC for
decoupling.
Device enable input. When the voltage on this pin rises above 1.4V, the device is enabled. The device is disabled when
the pin is pulled to ground. When the device is disabled, a 100Ω resistor discharges the output through the PHASE pin.
See Figure 3, “FUNCTIONAL BLOCK DIAGRAM” on page 4 for details.
Connect pin 3 to EPAD
Power-good output is pulled to ground during the soft-start interval and also when the output voltage is below regulation
limits. There is an internal 5MΩ internal pull-up resistor on this pin.
Feedback pin for the regulator. FB is the negative input to the voltage loop error amplifier. The output voltage is set by
an external resistor divider connected to FB. In addition, the power-good PWM regulator’s power-good and undervoltage
protection circuits use FB to monitor the output voltage.
Connect NC pin to EPAD
Power and analog ground connections. Connect directly to the board GROUND plane.
Power stage switching node for output voltage regulation. Connect to the output inductor. This pin is discharged by an
100Ω resistor when the device is disabled. See Figure 3, “FUNCTIONAL BLOCK DIAGRAM” on page 4 for details.
The exposed pad must be connected to the PGND pin for proper electrical performance. Place as many vias as possible
under the pad connecting to the PGND plane for optimal thermal performance.
Submit Document Feedback
3
FN6692.1
February 17, 2015


3Pages


ISL80015A 電子部品, 半導体
ISL80020, ISL80020A, ISL80015, ISL80015A
Absolute Maximum Ratings
VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6V (DC) or 7V (20ms)
PHASE . . . . . . . . . . . . . . -1.5V (100ns)/-0.3V (DC) to 6V (DC) or 7V (20ms)
EN, PG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VIN + 0.3V
FB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 2.7V
Junction Temperature Range at 0A . . . . . . . . . . . . . . . . . . . . . . . . . .+150°C
ESD Rating
Human Body Model (Tested per JESD22-JS-001) . . . . . . . . . . . . . . . . 4kV
Machine Model (Tested per JESD22-A115C) . . . . . . . . . . . . . . . . . . 300V
Charged Device Model (Tested per JESD22-C101D) . . . . . . . . . . . . . 2kV
Latch-up (Tested per JESD78D, Class 2, Level A) . . . ± 100mA at +125°C
Thermal Information
Thermal Resistance (Typical, Notes 4, 5) JA (°C/W) JC (°C/W)
2x2 TDFN Package . . . . . . . . . . . . . . . . . . .
71
7
Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . .-55°C to +125°C
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see TB493
Recommended Operating Conditions
VIN Supply Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V
Load Current Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0A to 2A
Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . .-40°C to +125°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
4. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379 for details.
5. For JC, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications TJ = -40°C to +125°C, VIN = 2.7V to 5.5V, unless otherwise noted. Typical values are at TA = +25°C. Boldface
limits apply across the operating temperature range, -40°C to +85°C.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
(Note 6)
MAX
TYP (Note 6) UNITS
INPUT SUPPLY
VIN Undervoltage Lockout Threshold
VUVLO
Rising, no load
Falling, no load
2.5 2.7 V
2.2 2.4
V
Quiescent Supply Current
Shutdown Supply Current
OUTPUT REGULATION
IVIN fSW = 1MHz, no load at the output
fSW = 2MHz, no load at the output
ISD VIN = 5.5V, EN = low
7 15 mA
10 22 mA
1.2 10 µA
Feedback Voltage
VFB Bias Current
Line Regulation
Load Regulation
VFB
TJ = -40°C to +125°C
IVFB VFB = 2.7V, TJ = -40°C to +125°C
VIN = VO + 0.5V to 5.5V (nominal 3.6V)
TJ = -40°C to +125°C
See (Note 7)
0.594
0.589
-350
-0.32
0.600
50
-0.05
< -0.2
0.606
0.606
350
0.28
V
V
nA
%/V
%/A
Soft-start Ramp Time Cycle (Note 7)
1 ms
PROTECTIONS
Positive Peak Current Limit
Thermal Shutdown
IPLIMIT
2A application (VIN = 3.6V)
1.5A application (VIN = 3.6V)
Temperature rising
2.8 3.18 3.6 A
2.1 2.5 2.9 A
150 °C
Thermal Shutdown Hysteresis (Note 7)
Temperature falling
25 °C
COMPENSATION
Error Amplifier Transconductance
(Note 7)
40 µA/V
Transresistance
RT
0.24
0.3
0.40
Ω
PHASE
P-channel MOSFET ON-resistance
N-channel MOSFET ON-resistance
VIN = 5V, IO = 200mA
VIN = 5V, IO = 200mA
117 mΩ
86 mΩ
Submit Document Feedback
6
FN6692.1
February 17, 2015

6 Page



ページ 合計 : 16 ページ
 
PDF
ダウンロード
[ ISL80015A データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
ISL80015

Compact Synchronous Buck Converters

Intersil Corporation
Intersil Corporation
ISL80015A

Compact Synchronous Buck Converters

Intersil Corporation
Intersil Corporation


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap