DataSheet.jp

MQ-9 の電気的特性と機能

MQ-9のメーカーはHANWEI ELETRONICSです、この部品の機能は「GAS SENSOR」です。


製品の詳細 ( Datasheet PDF )

部品番号 MQ-9
部品説明 GAS SENSOR
メーカ HANWEI ELETRONICS
ロゴ HANWEI ELETRONICS ロゴ 




このページの下部にプレビューとMQ-9ダウンロード(pdfファイル)リンクがあります。

Total 3 pages

No Preview Available !

MQ-9 Datasheet, MQ-9 PDF,ピン配置, 機能
HANWEI ELETRONICS CO.,LTD
MQ-9
http://www.hwsensor.com
TECHNICAL DATA
MQ-9 GAS SENSOR
FEATURES
* High sensitivity to carbon monoxide and CH4LPG.
* Stable and long life
APPLICATION
They are used in gas detecting equipment for carbon monoxide and CH4LPG in family
and industry or car.
SPECIFICATIONS
A. Standard work condition
Symbol
Vc
VH (H)
VH (L)
Parameter name
circuit voltage
Heating voltage (high)
Heating voltage (low)
technical condition
5V±0.1
5V±0.1
1.4V±0.1
Remark
AC or DC
AC or DC
AC or DC
RL Load resistance
Can adjust
RH
TH (H)
TH (L)
Heating resistance
Heating time (high)
Heating time (low)
33Ω ±5%
60±1 seconds
90±1 seconds
Room temperature
Ps Heating consumption Less than 340mw
b. Environment conditions
Symbol
Tao
Tas
RH
O2
Parameters
Using temperature
Storage temperature
Relative humidity
Oxygen concentration
c. Sensitivity characteristic
Technical conditions
-20+50℃
-20℃+50℃
Less than 95%RH
21%(stand condition)
the oxygen concentration can
affect the sensitivity
characteristic
Remark
Advice using scope
Minimum value is over 2%
symbol
Rs
а
(300/100ppm)
Standard working
condition
Preheat time
Parameters
Surface resistance
Of sensitive body
Concentration slope rate
Technical parameters
2-20k
Less than 0.5
Remark
In 100ppm
Carbon Monoxide
Rs (300ppm)/Rs(100ppm)
Temperature -20℃±2℃ relative humidity 65%±5% RL:10KΩ ±5%
Vc:5V±0.1V VH:5V±0.1V VH:1.4V±0.1V
No less than 48 hours
Detecting range:20ppm-2000ppm carbon monoxide
500ppm-10000ppm CH4
500ppm-10000ppm LPG
D. Structure and configuration, basic measuring circuit
Structure and configuration of MQ-9 gas sensor is shown as Fig. 1 (Configuration A or B),
sensor composed by micro AL2O3 ceramic tube, Tin Dioxide (SnO2) sensitive layer, measuring
electrode and heater are fixed into a crust made by plastic and stainless steel net. The heater
TEL: 86-371- 67169070 67169080 FAX: 86-371-67169090

1 Page





MQ-9 pdf, ピン配列
HANWEI ELETRONICS CO.,LTD
MQ-9
http://www.hwsensor.com
1. 5
1. 4
1. 3
1. 2
1. 1
1
0. 9
0. 8
0. 7
0. 6
0. 5
- 10 0
MQ- 9
10 20
Fig.4
33%RH
85%RH
30 40
Temp
50
Fig.4 is shows the typical
dependence of the MQ-9 on
temperature and humidity.
Ro: sensor resistance at 1000ppm LPG
in air at 33%RH and 20degree.
Rs: sensor resistance at 1000ppm LPG
at different temperatures and humidities.
OPERATION PRINCIPLE
. The surface resistance of the sensor Rs is obtained through effected voltage signal output of the
load resistance RL which series-wound. The relationship between them is described:
Rs\RL = (Vc-VRL) / VRL
VH5v
In air
In 100ppmCO
In 1000ppm LPG or 5000ppmCH4
In air
1.4v
Signal
60s 90s
Fig.5
Fig. 5 shows alterable situation of RL signal output measured by using Fig. 2 circuit output
signal when the sensor is shifted from clean air to carbon monoxide (CO) or CH4, output signal
measurement is made within one or two complete heating period (2.5 minute from high voltage
to low voltage ).
Sensitive layer of MQ-9 gas sensitive components is made of SnO2 with stability, So, it has
excellent long term stability. Its service life can reach 5 years under using condition.
SENSITVITY ADJUSTMENT
Resistance value of MQ-9 is difference to various kinds and various concentration gases. So, When
using this components, sensitivity adjustment is very necessary. we recommend that you calibrate the
detector for 200ppm and 5000ppm CH4 or 1000ppm LPG concentration in air and use value of Load
resistance that( RL) about 20 KΩ (10KΩ to 47 KΩ ).
When accurately measuring, the proper alarm point for the gas detector should be determined after
considering the temperature and humidity influence.
The sensitivity adjusting program:
a. Connect the sensor to the application circuit.
b. Turn on the power, keep time of preheating through electricity is over 48 hours.
c. Adjust the load resistance RL until you get a signal value which is respond to a certain
carbon monoxide concentration at the end point of 90 seconds.
d. Adjust the another load resistance RL until you get a signal value which is respond to a
CH4 or LPG concentration at the end point of 60 seconds .
TEL: 86-371- 67169070 67169080 FAX: 86-371-67169090


3Pages





ページ 合計 : 3 ページ
 
PDF
ダウンロード
[ MQ-9 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
MQ-1168

Evaluation Board Users Guide

MediaQ
MediaQ
MQ-1168

Multimedia Platform Controller

MediaQ
MediaQ
MQ-131

GAS SENSOR

ETC
ETC
MQ-135

Gas Sensor

Hanwei
Hanwei


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap