DataSheet.jp

GX520 の電気的特性と機能

GX520のメーカーはDellです、この部品の機能は「OptiPlex User Guide」です。


製品の詳細 ( Datasheet PDF )

部品番号 GX520
部品説明 OptiPlex User Guide
メーカ Dell
ロゴ Dell ロゴ 




このページの下部にプレビューとGX520ダウンロード(pdfファイル)リンクがあります。

Total 30 pages

No Preview Available !

GX520 Datasheet, GX520 PDF,ピン配置, 機能
Dell™ OptiPlex™ GX520 User's Guide
 
 Mini Tower Computer
 Desktop Computer
 Small Form Factor Computer
 

1 Page





GX520 pdf, ピン配列
l  Monitor the status of your computer, such as listening for thermal alerts from temperature probes or hard-drive failure alerts from storage devices.
l  Change the state of your computer, such as updating its BIOS or shutting it down remotely.
A managed system is one that has Dell OpenManage Client Instrumentation set up on a network that uses IT Assistant. For information about Dell
OpenManage Client Instrumentation, see the Dell OpenManage Client Instrumentation User's Guide available on the Dell Support website at support.dell.com.
 Security
 
Chassis Intrusion Detection
NOTE: When the administrator password is enabled, you must know the administrator password before you can reset the Chassis Intrusion setting.
This feature, if installed and enabled, detects that the chassis was opened and alerts the user. To change the Chassis Intrusion setting:
 
1. Enter system setup.
 
2. Press the down-arrow keys to move to the System Security option.
 
3. Press <Enter> to access the System Security option's pop-up menu.
 
4. Press the down-arrow key to move to the Chassis Intrusion setting.
 
5. Press <Enter> to select an option setting.
 
6. Press <Enter> again after you update the option setting.
 
7. Exit and save system setup.
 
Option Settings
l  On If the computer cover is opened, the setting changes to Detected, and the following alert message displays during the boot routine at the next
computer start-up:
Alert! Cover was previously removed.
To reset the Detected setting, enter system setup. In the Chassis Intrusion option, press the left- or right-arrow key to select Reset, and then choose
On, On-Silent, or Off.
l  On-Silent (default setting) If the computer cover is opened, the setting changes to Detected. No alert message appears during the boot sequence
at the next computer start-up.
l  Off No intrusion monitoring occurs and no messages appear.
 
Padlock Ring and Security Cable Slot
Use one of the following methods to secure your computer:
l  Use a padlock alone or a padlock and looped security cable with the padlock ring.
A padlock alone prevents the computer from being opened.
A security cable looped around a stationary object is used in conjunction with a padlock to prevent unauthorized movement of the computer.
l  Attach a commercially available antitheft device to the security cable slot on the back of the computer.
NOTE: Before you purchase an antitheft device, make sure that it works with the security cable slot on your computer.
Antitheft devices usually include a segment of metal-stranded cable with an attached locking device and key. The documentation that comes with the
device contains instructions for installing it.
 Password Protection
NOTICE: Although passwords provide security for the data on your computer, they are not foolproof. If your data requires more security, it is your
responsibility to obtain and use additional forms of protection, such as data encryption programs.
 


3Pages


GX520 電子部品, 半導体
To change an existing administrator password, you must know the administrator password.
 
1. Enter system setup.
 
2. Type the administrator password at the prompt.
 
3. Highlight Admin Password and press the left- or right-arrow key to delete the existing administrator password.
The setting changes to Not Set.
To assign a new administrator password, perform the steps in "Assigning an Administrator Password."
 
4. Exit system setup.
 
Disabling a Forgotten Password and Setting a New Password
To reset system and/or administrator passwords, see "Clearing Forgotten Passwords."
 System Setup
 
Overview
Use system setup as follows:
l  To change the system configuration information after you add, change, or remove any hardware in your computer
l  To set or change a user-selectable option such as the user password
l  To read the current amount of memory or set the type of hard drive installed
Before you use system setup, it is recommended that you write down the system setup screen information for future reference.
 
Entering System Setup
 
1. Turn on (or restart) your computer.
 
2. When the blue DELL™ logo appears, press <F2> immediately. 
If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft® Windows® desktop. Then shut down your
computer and try again.
 
System Setup Screens
The system setup screen displays current or changeable configuration information for your computer. Information on the screen is divided into three areas: the
options list, active options field, and key functions.
Options List This field appears on the left side of the system setup window. The field is a
scrollable list containing features that define the configuration of your computer, including
installed hardware, power conservation, and security features.
Option Field This field contains information about each
option. In this field you can view your current settings and
make changes to your settings.
Scroll up and down the list by using the up and down arrow keys. As an option is highlighted,
the Option Field displays more information about that option and the option's current and
available settings.
Use the right- and left-arrow keys to highlight an option.
Press <Enter> to make that selection active.
 
 
 
 
 
 
 
 

6 Page



ページ 合計 : 30 ページ
 
PDF
ダウンロード
[ GX520 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
GX520

OptiPlex User Guide

Dell
Dell


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap