DataSheet.jp

PCF0J151MCL1GS の電気的特性と機能

PCF0J151MCL1GSのメーカーはNichiconです、この部品の機能は「Aluminum Electrolytic Capacitor」です。


製品の詳細 ( Datasheet PDF )

部品番号 PCF0J151MCL1GS
部品説明 Aluminum Electrolytic Capacitor
メーカ Nichicon
ロゴ Nichicon ロゴ 




このページの下部にプレビューとPCF0J151MCL1GSダウンロード(pdfファイル)リンクがあります。

Total 3 pages

No Preview Available !

PCF0J151MCL1GS Datasheet, PCF0J151MCL1GS PDF,ピン配置, 機能
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CF Chip Type, Standard
series
Ultra-low ESR, High ripple current.
Load life of 2000 hours at 105°C.
SMD type : Lead free reflow soldering condition at 260°C
peak correspondence.
Compliant to the RoHS directive (2002/95/EC).
CV
High
Voltage
CG
Higher
Capacitance,
CS Long Life
CF
Low ESR CJ
Specifications
Item
Performance Characteristics
Category Temperature Range 55 to +105°C
Rated Voltage Range
2.5 to 25V
Rated Capacitance Range 3.3 to 1500µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C
ESR ( 1)
Less than or equal to the specified value at 100kHz, 20°C
Leakage Current ( 2) Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C 1.25
Z55°C / Z+20°C 1.25
(100kHz)
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Resistance to
Soldering Heat
Marking
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed
at right, provided that it's temperature profile is measured at the
capacitor top and the terminal.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface
shall not exceed 60 seconds.
In the case of peak temp, less than 250°C, reflow soldering shall
be two times maximum.
In the case of peak temp, less than 260°C, reflow soldering shall
be once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Navy blue print on the case top
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Capacitance
Lot No.
Plastic platform
0.3 MAX.
C±0.2
Positive
Type numbering system (Example : 6.3V 150µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
PC F 0 J 1 5 1 MC L 1 GS
Taping code
φD Code
4 to 6.3 5.5L GB
5 to 10 L 6 GS
Series
Voltage ( j:6.3v)
L
+0.1
- 0.4
Negative
H
(mm)
Size φ4 × 5.5L φ5 × 6L φ6.3 × 5.5L φ6.3 × 6L φ8 × 7L φ8 × 12L φ10 × 8L φ10 × 10L φ10 × 12.7L
φD 4.0 5.0 6.3 6.3 8.0 8.0 10.0 10.0 10.0
L 5.4 5.9 5.4 5.9 6.9 11.9 7.9 9.9 12.6
A 5.0 6.0 7.3 7.3 9.0 9.0 11.0 11.0 11.0
B 4.3 5.3 6.6 6.6 8.3 8.3 10.3 10.3 10.3
C 4.3 5.3 6.6 6.6 8.3 8.3 10.3 10.3 10.3
E 1.0 1.6 2.1 2.1 3.2 3.2 4.6 4.6 4.6
H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
Configuration
Capacitance toleranc (±20%)
Rated capacitance (150µF)
Rated voltage (6.3V)
Series name
Type
Size code
Voltage
V 2.5 4 6.3 10 16 20 25
Code e g j A C D E
Dimension table in next page.
CAT.8100Z

1 Page





PCF0J151MCL1GS pdf, ピン配列
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CF series
Standard Ratings
Rated Voltage Surge Voltage Rated Capacitance
(V)(code)
(V)
(µF)
3.3
22
33
39
39
16 18.4
1C
56
82
100
150
180
180
220
220
330
10
22
22
39
47
20 23
1D
56
68
82
100
120
150
6.8
10
25 28.7
1E
22
33
47
47
56
Case Size
φD × L (mm)
4 × 5.5
5×6
6.3 × 6
6.3 × 5.5
6.3 × 6
8×7
8×7
10 × 8
10 × 8
8 × 12
10 × 8
10 × 10
10 × 12.7
10 × 12.7
5×6
6.3 × 5.5
6.3 × 6
8×7
8×7
10 × 8
10 × 8
10 × 8
8 × 12
10 × 10
10 × 12.7
6.3 × 6
8×7
10 × 8
8 × 12
8 × 12
10 × 10
10 × 12.7
tan δ
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
Leakage Current
ESR (m)
Rated Ripple
(µA) (at 100kHz 20° ) (mArms)
Part Number
100 260
660 PCF1C3R3MCL1GB
176
45
1210
PCF1C220MCL1GS
106
31
2400
PCF1C330MCL1GS
125
31
2400
PCF1C390MCL4GB
125
31
2400
PCF1C390MCL1GS
179
30
2900
PCF1C560MCL1GS
262
28
3200
PCF1C820MCL1GS
320
27
3300
PCF1C101MCL1GS
480
25
3500
PCF1C151MCL1GS
576
16
4400
PCF1C181MCL4GS
576
25
3600
PCF1C181MCL1GS
704
20
3900
PCF1C221MCL1GS
704
14
5050
PCF1C221MCL9GS
1056
14
5000
PCF1C331MCL1GS
100 120
900 PCF1D100MCL1GS
100
50
1700
PCF1D220MCL4GB
88
50
1700
PCF1D220MCL1GS
156
45
2000
PCF1D390MCL1GS
188
45
2000
PCF1D470MCL1GS
224
40
2400
PCF1D560MCL1GS
272
40
2600
PCF1D680MCL1GS
328
40
2600
PCF1D820MCL1GS
400
22
3200
PCF1D101MCL1GS
480
35
2800
PCF1D121MCL1GS
600
20
4320
PCF1D151MCL1GS
85
80
1200
PCF1E6R8MCL1GS
125
60
1600
PCF1E100MCL1GS
275
50
2200
PCF1E220MCL1GS
413
30
2800
PCF1E330MCL1GS
588
30
3000
PCF1E470MCL4GS
588
45
2400
PCF1E470MCL1GS
700
28
3800
PCF1E560MCL1GS
Rated ripple current (mArms) at 105°C 100kHz
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Please refer to page 3 for the minimum order quantity.
No marked, 1 will be put at 12th digit of type numbering system.
: In this case, 4 will be put at 12th digit of type numbering system.
: In this case, 6 will be put at 12th digit of type numbering system.
: In this case, 9 will be put at 12th digit of type numbering system.
CAT.8100Z


3Pages





ページ 合計 : 3 ページ
 
PDF
ダウンロード
[ PCF0J151MCL1GS データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
PCF0J151MCL1GS

Aluminum Electrolytic Capacitor

Nichicon
Nichicon


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap