|
|
Z0M300-RC-10のメーカーはSuperworld Electronicsです、この部品の機能は「FERRITE CHIP BEADS」です。 |
部品番号 | Z0M300-RC-10 |
| |
部品説明 | FERRITE CHIP BEADS | ||
メーカ | Superworld Electronics | ||
ロゴ | |||
このページの下部にプレビューとZ0M300-RC-10ダウンロード(pdfファイル)リンクがあります。 Total 9 pages
FERRITE CHIP BEADS
Z0 SERIES
1. PART NO. EXPRESSION :
Z0K121-RB-10
(a)(b)(c) (d) (e)(f) (g)
(a) Series code
(b) Dimension code
(c) Material code
(d) Impedance code : 470 = 47ȍ
2. CONFIGURATION & DIMENSIONS :
A
D
(e) R : Reel
(f) Current : C = 300mA
(g) : 10 : RoHS Compliant
11 ~ 99 : Internal controlled number
B
Unit:m/m
ABCD
0.60±0.03 0.30±0.03 0.30±0.03 0.15±0.05
3. SCHEMATIC :
4. MATERIALS :
ba
Ag(100%)
Ni(100%)-1.5um(min.)
Sn(100%)-3.0um(min.)
(a) Body : Ferrite
(b) Termination : Ag/Ni/Sn
5. GENERAL SPECIFICATION :
a) Temp. rise : 30°C Max.
b) Rated current : Base on temp. rise
c) Storage temp. : -55°C to +125°C
d) Operating temp. : -55°C to +125°C ( include self-temp. rise )
e) Resistance to solder heat : 260°C.10secs
www.DataSheet4U.com
NOTE : Specifications subject to change without notice. Please check our website for latest information.
SUPERWORLD ELECTRONICS
(S)
PTE
11.08.2010
LTD
PG. 1
1 Page FERRITE CHIP BEADS
7. IMPEDANCE VS. FREQUENCY CURVES :
FCMZ000M6M0333000M0-RF-RC-3C-
0-10
0T03
180
120
60
0
1
300
Z
R
10 100
F REQUE NCY(M H z)
X
100 0
FCMZZ00M66060300M0--RFRA-A-6
-01
00T01
200
100
0
1
Z
X
R
10 100
F REQU ENCY(M Hz)
100 0
30 0
20 0
10 0
0
1
Z0 SERIES
F CMZ0Z06M0 0M4374M07-R0F--BR4-B7
0-
1T00 2
Z
X
R
1 0 100
FREQ UENCY( MHz)
1 00 0
www.DataSheet4U.com
NOTE : Specifications subject to change without notice. Please check our website for latest information.
SUPERWORLD ELECTRONICS
(S)
PTE
11.08.2010
LTD
PG. 3
3Pages FERRITE CHIP BEADS
Z0 SERIES
9. SOLDERING AND MOUNTING :
9-1. Recommended PC Board Pattern
0.80
0.30
PC board should be designed so that products are not sufficient
under mechanical stress as warping the board.
Products shall be positioned in the sideway direction against
the mechanical stress to prevent failure.
9-2. Soldering
Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused
by the difference in coefficients of expansion between solder, chip and substrate. The terminations are suitable for all
wave and re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot
air soldering tools.
9-2.1 Lead Free Solder Re-flow :
Recommended temperature profiles for re-flow soldering in Figure 1.
9-2.2 Solder Wave :
Wave soldering is perhaps the most rigorous of surface mount soldering processes due to the steep rise in temperature
seen by the circuit when immersed in the molten solder wave. Due to the risk of thermal damage to products, wave
soldering of large size products is discouraged. Recommended temperature profile for wave soldering is shown
in Fig. 2
9-2.3 Soldering Iron (Figure 3) :
Products attachment with soldering iron is discouraged due to the inherent process control limitations. In the event that
a soldering iron must be employed the following precautions are recommended.
Note :
a) Preheat circuit and products to 150°C.
d) 1.0mm tip diameter (max)
b) 350°C tip temperature (max)
e) Use a 20 watt soldering iron with tip diameter of 1.0mm
c) Never contact the ceramic with the iron tip
f) Limit soldering time to 3 secs.
Preheating
TP(260°C/10s max.)
Soldering
20~40s
Natural
cooling
217
200
150 60~150s
60~180s
480s max.
25
Time(sec.)
Figure 1. Re-flow Soldering
Preheating
260
245
150
Soldering
Natural
cooling
Preheating
350
330
150
Soldering
3s
(max.)
10s
(max.)
Natural
cooling
Over 2min.
Gradual
Cooling
Within 10s
Figure 2. Wave Soldering
www.DataSheet4U.com
Over 1min.
Gradual
Cooling
Figure 3. Hand Soldering
NOTE : Specifications subject to change without notice. Please check our website for latest information.
SUPERWORLD ELECTRONICS
(S)
PTE
11.08.2010
LTD
PG. 6
6 Page | |||
ページ | 合計 : 9 ページ | ||
|
PDF ダウンロード | [ Z0M300-RC-10 データシート.PDF ] |
データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。 |
部品番号 | 部品説明 | メーカ |
Z0M300-RC-10 | FERRITE CHIP BEADS | Superworld Electronics |
Z0M300-RC-11 | FERRITE CHIP BEADS | Superworld Electronics |