|
|
PDF LTA170C07RF Data sheet ( Hoja de datos )
| Número de pieza | LTA170C07RF | |
| Descripción | TFT LCD Module | |
| Fabricantes | Toshiba | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LTA170C07RF (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
To :
This specification is only used for discussing the included items.
You haven’t to approve this specification.
When we shall agree the specification, we will issue the formal one.
SPECIFICATION(TENTATIVE)
FOR
Toshiba Matsushita Display Technology TFT-LCD MODULE
LTA170C07RF
LTA 1 7 0 C 0 7 R F - 0 1
DATE OF ISSUE : 2003-06-18
TV/PC/Monitor-Use Marketing & Engineering Group2
TV/PC/Monitor-Use Marketing & Engineering Dept.
AVC-Use LCD Division
Toshiba Matsushita Display Technology Co.,Ltd.
1-9-2, Hatara-cho, Fukaya-shi, Saitama, 366-0032, JAPAN (Toshiba Fukaya Operations)
1 page  
For Designing the System
Specification No. TENTATIVE
Sheet 4
2-1 DESIGNING ENCLOSURE
1) MECHANICAL DIMENSIONS
Refer to the individual specification for LCD module's mechanical dimensions.
2) MOUNTING HOLES
LCD module should be assembled to the system by using all mounting holes specified in the individual
specification with the specified screws.
In addition, some modules may not be necessary to use all the mounting holes. Make comprehensive
judgments on the entire system.
3) Ú BENDING / TWISTING
Make sure to design the enclosure that bending/twisting forces are not applied to LCD module during and
after the installation into the system.
4) GASES FROM SETTING MATERIAL
Some plastic materials and shock absorbing materials (rubber) used in the system may generate gases that
may cause the deterioration of the polarizer laminated on LCD’s panel or internal parts of the module. Prior
confirmation is required.
5) GASES FROM PACKAGING MATERIAL
Some materials used for packaging (for which sulfuric acid is used in the recycling process) generate gases
that may cause the deterioration of the polarizer laminated on LCD’s panel or internal parts of the module.
Prior confirmation is required.
2-2 DESIGNING POWER SUPPLIES AND INPUT SIGNALS TO LCD MODULE
1) CAPACITY OF POWER SUPPLY
Refer to individual specification for details for capacity of power supply, and apply some protection circuit
including fuses for power supply lines.
2) SEQUENCE OF POWER SUPPLIES AND INPUT SIGNALS
Power supply lines should be designed as follows.
Power supplies should always be turned on before the input signals are applied to LCD module, and the
input signals should be disconnected before power supplies are turned off.
The detailed sequence of power supplies and signals are described in the individual specification.
In addition, refer to individual specifications for unused terminals.
3) FL CABLE CONNECTION
Make sure to connect correctly high-voltage wire and low-voltage wire between FL tube and inverter unit.
If high-voltage wire and low-voltage wire are connected incorrectly, it may cause insufficient brightness or
unstable operation of FL, and smoke or burn of the parts.
4) PREVENTION OF IMAGE STICKING
Design the system not to display same pattern for a long time in order to prevent image sticking on the
panel. Note that incorrect sequence of power supplies and input signals may cause the sticking on the
panel, too.
Toshiba Matsushita Display Technology Co.,Ltd
Date: 2003-06-18
Date: - -
New No. LTA170C07RF-01
Old No.
←# Special ←& Addition ← Change
5 Page 
Specification No. TENTATIVE
Sheet 10
1. Scope
This specification is applicable to Toshiba Matsushita Display Technology's 43 cm diagonal size TFT-LCD module
"LTA170C07RF" designed for TV.
2. Product Specifications
2.1 General Specifications
Item
Display Mode
Viewing Direction
Driving Method
Input Signals
Dimensional Outline
Active Area
Viewing Area
Number of Pixels
Pixel Pitch
Pixel Arrangement
Surface Treatment
Backlight
Specifications
TN color (253 gray scales, 16,194,277 colors)
Transmissive type, Normally white
6 o'clock (in direction of maximum contrast)
TFT active matrix
C-MOS 8Bit × RGB
385 (W) × 303 (H) × 17.5 (D) (mm)
343.68 (W) × 261.60 (H) (mm)
349 (W) × 267 (H) (mm)
640 (W) × 480
(H) 1)
0.545 (W) × 0.537 (H) (mm) 1)
RGB vertical stripes 1)
Low Reflection & Anti-glare hard coat on LCD surface
4 cold-cathode fluorescent lamps (L-Type)
Note 1) Display area address is as follows.
1
1 RGBRGB
2 RGBRGB
2
RGBRGB
R G BR G B
RGB
: pixel
R G BR G B
479
RGBRGB
480
RGBRGB
R G B : Sub-pixel
(Dots)
R G B R G B 0.446mm
0.446mm
Toshiba Matsushita Display Technology Co.,Ltd
Date: 2003-06-18
Date: - -
New No. LTA170C07RF-01
Old No.
←# Special ←& Addition ← Change
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet LTA170C07RF.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LTA170C07RF | TFT LCD Module | Toshiba |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |