|
|
MC9S08FL8のメーカーはFreescale Semiconductorです、この部品の機能は「Microcontrollers」です。 |
部品番号 | MC9S08FL8 |
| |
部品説明 | Microcontrollers | ||
メーカ | Freescale Semiconductor | ||
ロゴ | |||
このページの下部にプレビューとMC9S08FL8ダウンロード(pdfファイル)リンクがあります。 Total 30 pages
MC9S08FL16
MC9S08FL8
Reference Manual
HCS08
Microcontrollers
Related Documentation:
• MC9S08FL16 (Data Sheet)
Contains pin assignments and diagrams, all electrical
specifications, and mechanical drawing outlines.
Find the most current versions of all documents at:
http://www.freescale.com
MC9S08FL16RM
Rev. 1
3/2009
freescale.com
1 Page MC9S08FL16 Features
8-Bit S08 Central Processor Unit (CPU)
• Up to 20 MHz CPU at 4.5 V to 5.5 V across
temperature range –40 °C to 85 °C
• HC08 instruction set with added BGND
instruction
• Support for up to 32 interrupt/reset sources
On-Chip Memory
• Up to 16 KB flash read/program/erase over
full operating voltage and temperature
• Up to 1024-byte random-access memory
(RAM)
• Security circuitry to prevent unauthorized
access to RAM and flash contents
Power-Saving Modes
• Two low power stop modes; reduced power
wait mode
• Allowing clocks to remain enabled to
specific peripherals in stop3 mode
Clock Source Options
• Oscillator (XOSC) — Loop-control Pierce
oscillator; crystal or ceramic resonator
range of 31.25 kHz to 39.0625 kHz or
1 MHz to 16 MHz
• Internal Clock Source (ICS) — Internal
clock source module containing a
frequency-locked-loop (FLL) controlled by
internal or external reference; precision
trimming of internal reference allows 0.2%
resolution and 2% deviation over
temperature and voltage; supports bus
frequencies up to 10 MHz
System Protection
• Watchdog computer operating properly
(COP) reset with option to run from
dedicated 1 kHz internal clock source or
bus clock
• Low-voltage detection with reset or
interrupt; selectable trip points
• Illegal opcode detection with reset
• Illegal address detection with reset
• Flash block protection
Development Support
• Single-wire background debug interface
• Breakpoint capability to allow single
breakpoint setting during in-circuit
debugging (plus two more breakpoints)
• On-chip in-circuit emulator (ICE) debug
module containing two comparators and
nine trigger modes
Peripherals
• IPC — Interrupt priority controller to
provide hardware based nested interrupt
ADC — 12-channel, 8-bit resolution;
2.5 μs conversion time; automatic compare
function; 1.7 mV/°C temperature sensor;
internal bandgap reference channel;
operation in stop; optional hardware
trigger; fully functional from 4.5V to 5.5 V
• TPM — One 4-channel and one 2-channel
timer/pulse-width modulators (TPM)
modules; selectable input capture, output
compare, or buffered edge- or
center-aligned PWM on each channel
• MTIM16 — One 16-bit modulo timer with
optional prescaler
• SCI — One serial communications
interface module with optional 13-bit
break; LIN extensions
Input/Output
• 30 GPIOs including one input-only pin and
one output-only pin
Package Options
• 32-pin LQFP
• 32-pin SDIP
3Pages Revision History
To provide the most up-to-date information, the revision of our documents on the World Wide Web will
be the most current. Your printed copy may be an earlier revision. To verify you have the latest information
available, refer to:
http://freescale.com
The following revision history table summarizes changes contained in this document.
Revision
Number
1
Revision
Date
3/20/2009
Initial public release.
Description of Changes
This product incorporates SuperFlash® technology licensed from SST.
Freescale and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
© Freescale Semiconductor, Inc., 2009. All rights reserved.
MC9S08FL16 MCU Series Reference Manual, Rev. 1
6
Freescale Semiconductor
6 Page | |||
ページ | 合計 : 30 ページ | ||
|
PDF ダウンロード | [ MC9S08FL8 データシート.PDF ] |
データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。 |
部品番号 | 部品説明 | メーカ |
MC9S08FL16 | Microcontrollers | Freescale Semiconductor |
MC9S08FL8 | Microcontrollers | Freescale Semiconductor |