DataSheet.jp

S4132B の電気的特性と機能

S4132BのメーカーはALTRONICSです、この部品の機能は「PCB Relay」です。


製品の詳細 ( Datasheet PDF )

部品番号 S4132B
部品説明 PCB Relay
メーカ ALTRONICS
ロゴ ALTRONICS ロゴ 




このページの下部にプレビューとS4132Bダウンロード(pdfファイル)リンクがあります。
Total 4 pages

No Preview Available !

S4132B Datasheet, S4132B PDF,ピン配置, 機能
S 4128B
S 4130B
S 4132B
PCB Relay Telecom 5V 2A DPDT
PCB Relay Telecom 12V 2A DPDT
PCB Relay Telecom 24V 2A DPDT
Supplier Ordering Info
P-5
P-12
P-24
19/04/10
Features
DIL Pitch Terminals .High Sensitivity :0.14W or 0.10W Nominal Power
Conforms to FCC Part 68 1.5kV Surge and Dielectric 1000VAC
Monostable or bistable relays Single and double Coil magnet latching Type available
Application for Telecommunication Equipment,Office Equipment,Security Alarm Systems, Measuring instruments,
Medical Monitoring Equipment,Audio Visual Equipment, Flight Simulator,Sensor Control
Contact Data
Contact Arrangement
Contact Material
Contact Rating (resistive)
Max. Switching Power
Max. Switching Voltage
Contact Resistance or
Voltage drop
Operation
life
Electrical
Mechanical
2C DPDT(B-M) Bifurcated Crossbar
AgPd(Stationary Contact: Gold clad )
1A,2A/30VDC; 0.5A/125VAC
60W
62.5VA
Min. Switching load 0.01mA/10mV Reference Value
220VDC 250VAC
Max. Switching Current:2A
50m
Item 4.12 of IEC 61810-7
1A/30VDC 2 105 Ag Ni 1 105
0.5A/125VAC 1 105
108
Item 4.30 of IEC 61810-7
Item 4.31 of IEC 61810-7
CAUTION:
Relays previously tested or used above 10mA resistive at 6V maximum DC or peak AC open circuit are not
recommended for subsequent use in low level applications.
Coil Parameter
Dash
numbers
Coil voltage
VDC
Rated
Max.
Coil resistance
10%
Pick up voltage
VDC(max)
(75%of rated
voltage )
Release voltage
VDC(min)
(10% of rated
voltage)
Coil
power
W
Operate
Time
ms
Release
/Reset
Time
ms
S 4128B
S 4130B
S 4132B
5 12.5
12 30.0
24 48.0
178
1028
2880
3.75
9.00
18.0
0.5 0.14
1.2 0.14 Approx.2 Approx.1
2.4 0.20
CAUTION: 1.The use of any coil voltage less than the rated coil voltage will compromise the operation of the relay.
2.Pickup and release(reset) voltage are for test purposes only and are not to be used as design
criteria.
3.When latching relays are installed in equipment, the latch and reset coil should not be pulsed
simultaneously. Coil should not be pulsed with less than the nominal coil voltage and pulse width
should be a minimum of three times the specified operate time of the relay. If these conditions are not
followed, it is possible for the relay to be in the magnetically neutral position .
1

1 Page





S4132B pdf, ピン配列
SOLDERING and MOUNTING RECOMMENDATIONS
1. Conditions for Terminal Soldering by re ow soldering method
a. In case of Infrared Soldering
b. In case of Vapor Phase Soldering
Fig.1
Fig.2
T3
T2
T1
t1
Time
t2
T1:+120 to+150 oC(+248 to+302 oF)
T2:+180 to+200 oC(+356 to+392 oF)
T3:+245 oC(+473 oF)Max.
t1:60 to 90 Sec.
t2:+30Sec.Max.
T3
T2
T1
t1
Time
t2
T1:+120 to+150 oC(+248 to+302 oF)
T2:+180 to+200 oC(+356 to+392 oF)
T3:+215 oC(+419 oF)Max.
t1:+40 to 60Ses
t2:+60Sec.Max.
2. Usage of Stand-O A &B in Base Area
Fig.3
The Stand-O s shown in the F ig. 3 are designed to
Anchor Relays temporarily to PCBoard with glue before
Terminal Soldering.
Stand-o B
Stand-o B
Stand-o A
Pick-up/Drop-Out Voltage(P)
50
n=100
Drop-Out
40
Pick-up
30
20
10
0 0 10 20 30 40 50 60 70 80 90 100
Ratio to the Nominal oVltage(%)
Operate/Release Time(P)
(without Diode)
5
4
3
2
Operate Time
1
Release Time
0
0 80 100 120 140
Coil applied Voltage(%)
160
100
80
60
40
20
00
Operate/Release Time(P)
n=100
Release
Operate
0.5 1 1.5
Time(ms)
2 2.5
Set/Reset Voltage(PL)
50
n=100
40
Reset Voltage
30
Set Voltage
20
10
0 0 10 20 30 40 50 60 70 80 90 100
Ratio to the Nominal oVltage(%)
Operate/Release Time(P)
(without Diode)
5
4
3
2
Operate Time
1
Release Time
0
0 80 100 120 140 160
Coil applied Voltage(%)
Set/Reset Time(PL)
100
n=50
80
Set Time
60
Reset Time
40
20
00 1
20
Time(ms)
1
2
3
Contact Resistance
50
n=200
40
30
20
10
0 20 30 40 50 60
Contact Resistance(m )
Set/Reset Time(PL)
5
4
3
2
Set Time
1
Reset Time
0
0 80 100 120 140 160
Coil applied Voltage(%)
105
80
60
40
20
00
Coil temperature rise(P)
1A
0A
80 100 120 140
Coil applied Voltage(%)
160


3Pages





ページ 合計 : 4 ページ
 
PDF
ダウンロード
[ S4132B データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
S4132B

PCB Relay

ALTRONICS
ALTRONICS


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap