DataSheet.jp

TL1L2-NW1L の電気的特性と機能

TL1L2-NW1LのメーカーはToshibaです、この部品の機能は「LED Lamps」です。


製品の詳細 ( Datasheet PDF )

部品番号 TL1L2-NW1L
部品説明 LED Lamps
メーカ Toshiba
ロゴ Toshiba ロゴ 




このページの下部にプレビューとTL1L2-NW1Lダウンロード(pdfファイル)リンクがあります。

Total 14 pages

No Preview Available !

TL1L2-NW1L Datasheet, TL1L2-NW1L PDF,ピン配置, 機能
LED Lamps InGaN and Phosphor
TL1L2-NW1,L
1. Applications
• General Lighting
2. Features
(1) Size: 3.5 (L) mm × 3.5 (W) mm × 1.93 (H) mm
(2) High luminous flux LED: 128 lm (typ.) @IF = 350 mA
(3) Color: White (color temperature: 5000 K (typ.))
(4) High Color Rendering Index : Ra = 80 (min)
(5) Operating temperature range: Topr = -40 to 100
(6) Reflow-soldering is available.
3. Packaging and Pin Assignment
4-4M1
TL1L2-NW1,L
1: Anode
2: Cathode
Start of commercial production
2014-03
1 2014-04-21
Rev.2.0

1 Page





TL1L2-NW1L pdf, ピン配列
TL1L2-NW1,L
5. Handling Precautions
• This product is sensitive to electrostatic and care must be fully taken when handling products. Particularly
in the case that an overvoltage shall be applied, the overflowed energy may cause damage to or possibly
result in destruction of the product. Users shall take absolutely secure countermeasures against
electrostatic and surge when handling the product.
• A damage to the device might create a tiny leakage path, which causes the LED lamp not to light up in the
low-current region or causes a drop in the VF rise voltage.
Failure criterion: IF 0.5 mA @ VF = 2 V
• If multiple LEDs are connected in parallel, they will experience variations in the forward current due to
the characteristics differences in forward voltage. Ensure that the forward current of all the LEDs fall
within the intended range of the system design, for example, by inserting current-limiting resistors to each
LED string.
• Since this product is intended to be used for display lighting, the measurement standard is based on the
spectral sensitivity of the human eye. It is not intended to be used for any applications other than display
lighting (e.g., sensors and light communications systems.)
• Generally, GaN-based LEDs exhibit instability or significant device-to-device variations in the relative
luminous flux in the low-current region. To avoid these problems, an application system should be
designed in such a manner that the GaN-based LEDs are driven with a forward current of 10 mA or
higher.
• This device should not be reverse-biased.
• When the device is used in places that are likely to be exposed to condensation, salt or corrosive gas, the
effect on its performance and reliability must be thoroughly verified
• Please note the handling of products during evaluation.
(1) Please do not apply pressure to the upper surface of the product with finger, tweezers, and others.
Failure of product to light up may occur due to package deformation, wire deformation and/or
disconnection.
(2) Should tweezers be used in product handling, one with flat surfaces is recommended.
(3) Please handle the product widthwise.
(4) Please do not drop the product. There is a possibility for package transformation etc. to occur when the
product is dropped.
(5) Please do not stack the printed circuit boards on which the product is mounted to prevent damages to
product surface. Also, please note not to damage the surface of the product with cushioning material
etc. Surface damage to the product may influence their optical characteristics.
(6) Solder, flux, paper or heat-sensitive materials that might be deformed or discolored at high
temperatures should not be left on the surface of an LED lamp.
• Extreme care should be exercised when using this device for high-power applications:
(1) Do not directly touch this device during active operation because it becomes hot,
depending on the operating power.
(2) Take a possible rise in ambient temperature around this device and the heat-resistant temperature of
the system components into consideration.
3 2014-04-21
Rev.2.0


3Pages


TL1L2-NW1L 電子部品, 半導体
8. Characteristics Curves (Note)
TL1L2-NW1,L
Fig. 8.1 IF - VF
Fig. 8.2 Relative Luminous Flux - IF
Fig. 8.3 Relative Luminous Flux - Ta
Fig. 8.4 Chromaticity - IF
Fig. 8.5 Chromaticity - Ta
Fig. 8.6 Wavelength Characteristic
6 2014-04-21
Rev.2.0

6 Page



ページ 合計 : 14 ページ
 
PDF
ダウンロード
[ TL1L2-NW1L データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
TL1L2-NW1

LED Lamps

Toshiba
Toshiba
TL1L2-NW1L

LED Lamps

Toshiba
Toshiba


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap