DataSheet.jp

LQ6NC02 の電気的特性と機能

LQ6NC02のメーカーはSharpです、この部品の機能は「TFT LCD Module」です。


製品の詳細 ( Datasheet PDF )

部品番号 LQ6NC02
部品説明 TFT LCD Module
メーカ Sharp
ロゴ Sharp ロゴ 




このページの下部にプレビューとLQ6NC02ダウンロード(pdfファイル)リンクがあります。
Total 23 pages

No Preview Available !

LQ6NC02 Datasheet, LQ6NC02 PDF,ピン配置, 機能
LCD Data Sheet
LQ6NC01/LQ6NC02
TFT-LCD Module
FEATURES
TFT-Active Matrix-LCD Drive System
240 (V) × 720 (H) (Total 172,800) Dots
(Delta Configuration)
Slim, Lightweight and Compact:
Active Area/Outline Area: 57%
Thickness: 23 mm
Weight: 320 g
Built-in Video Interface Circuit (including
chroma demodulator, picture tone, video
ACG circuit) and Control Circuit
Responsive to Composite Video Signal
Also Responsive to Standard Analog
RGB Video Signals
Further RGB Signals can be
Superimposed on Composite Video
Signal (in this case, RGB signals shall be
digital input signal for eight colors display)
High-Quality, Full-Color Rendition With
Backlight Source Incorporated
Viewing Angle:
6 O’Clock Direction: LQ6NC01
12 O’Clock Direction: LQ6NC02
DESCRIPTION
The SHARP LQ6NC01/LQ6NC02 Color TFT-LCD
module is an active matrix LCD (Liquid Crystal Dis-
play) produced by making the most of Sharp’s exper-
tise in liquid-crystal and semiconductor technologies.
The active device is amorphous silicon TFT (Thin Film
Transistor). The module accepts full-color video sig-
nals (composite video and analog RGB) conforming
to the NTSC (M) system standard.
When additionally provided with the backlight-driv-
ing DC/AC inverter, it is applicable to pocket TVs and
various display monitors.
The module consists of a TFT-LCD panel, driver
ICs, control PWB mounted with electronic circuits,
flourescent tube, reflector, frame, front and rear
shielding cases.
NOTE: Backlight-driving DC/AC inverter is not built
into the module.
LCD Data Sheet
Page 1

1 Page





LQ6NC02 pdf, ピン配列
TFT-LCD Module
LQ6NC01/LQ6NC02
FRONT CASE
TFT-LCD PANEL
FLUORESCENT TUBE
FLUORESCENT TUBE
HOLDING PWB
REFLECTOR
GATE DRIVER
FRAME
SOURCE DRIVER
CONTROL PWB
SHIELDING CASE
Figure 2. LQ6NC01/LQ6NC02 TFT-LCD Module Construction
5703-7
LCD Data Sheet
Page 3


3Pages


LQ6NC02 電子部品, 半導体
LQ6NC01/LQ6NC02
TFT-LCD Module
INPUT/OUTPUT TERMINALS – TFT-LCD PANEL DRIVING SECTION
PIN
NUMBER
1
2
3
4
5
6
7
8
SYMBOL
HSY
VSY
TST
NC
TST
GND
VSW
GND
9 VCDC
10 VSH
11 VBS
12 BRT
13 CNT
14 COL
15 TIN
16 VSL
17 VRI
18 VGI
19 VBI
20 GND
I/O DESCRIPTION
O Internal Horizontal Sync Signal (In phase with VBS)
O Internal Vertical Sync Signal (In phase with VBS)
This is Electrically Opened During Operation
I Ground
I Selection Signal of Two Sets of Video Signals
I Ground
I
DC Bias Voltage Adjusting Terminal of Common Electrode
Driving Signal
I Positive Power Supply Voltage
I Composite Video Signal
I Brightness Adjusting Terminal
I Contrast Adjusting Terminal
I Color Gain Adjusting Terminal
I Tint Adjusting Terminal
I Negative Power Supply Voltage
I Color Video Signal – Red
I Color Video Signal – Green
I Color Video Signal – Blue
I Ground
NOTE
1
2
3
4
5
NOTES:
In the following descriptions, ‘High’ means ‘VSH’ and ‘Low’ means ‘GND.’
1. Selects input signals, composite or RGB:
a. When VSW is ‘High’ or open, composite video signal (Pin Number 13) is selected.
b. When VSW is ‘Low,’ RGB signal set (Pin Numbers 17 through 19) is selected.
2. Common electrode driving signal (VCOM) generated in the module is observed on the pin. This should be opened during operation,
since the DC component of VCOM (VCDC) is adjusted before shipping to the optimum value with VSH and VSL being the typical value.
If the optimum value changes (for example, lowering of the power source), it should be re-adjusted with the built-in variable resistor
(VCDC) or external circuit shown in Figure 5. Refer to ‘Adjusting Method of Optimum Common Electrode DC Bias Voltage’ for
readjusting.
3. Similarly, in case of RGB input, apply composite video signal or composite sync signal (with negative polarity) for sync separator.
4. Brightness, Contrast, Color Gain and Tint are adjusted by the DC voltage supplied to each pin. (Contrast, color gain, and tint are not
available for RGB signal input). They are adjusted to the optimum value on shipping but they can be re-adjusted with the built-in
variable resistor (BRT, CNT, COL, TIN) or external circuit shown in Figure 5. (However, since the contrast is adjusted to maximize
display characteristics, it is recommended not to readjust it and to keep outer adjustment terminals open.)
5. a. Responsive to 0 VP-P to 0.7 VP-P analog RGB signal when VSW is fixed to ‘Low.’
b. In case of superimposing on composite video signal as on screen display (refer to Note 1), RGB signals shall be digital signal
(Low: 0 VP-P High: > 2 VP-P available for eight colors display).
Page 6
LCD Data Sheet

6 Page



ページ 合計 : 23 ページ
 
PDF
ダウンロード
[ LQ6NC02 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
LQ6NC01

TFT LCD Module

Sharp
Sharp
LQ6NC02

TFT LCD Module

Sharp
Sharp


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap