DataSheet.jp

UM10398 の電気的特性と機能

UM10398のメーカーはNXP Semiconductorsです、この部品の機能は「LPC111x/LPC11Cxx I/O User manual」です。


製品の詳細 ( Datasheet PDF )

部品番号 UM10398
部品説明 LPC111x/LPC11Cxx I/O User manual
メーカ NXP Semiconductors
ロゴ NXP Semiconductors ロゴ 




このページの下部にプレビューとUM10398ダウンロード(pdfファイル)リンクがあります。
Total 70 pages

No Preview Available !

UM10398 Datasheet, UM10398 PDF,ピン配置, 機能
UM10398
LPC111x/LPC11Cxx User manual
Rev. 12.3 — 10 June 2014
User manual
Document information
Info Content
Keywords
ARM Cortex-M0, LPC1111, LPC1112, LPC1113, LPC1114, LPC1115,
LPC11C12, LPC11C14, LPC1100, LPC1100L, LPC11C00, LPC11C22,
LPC11C24, LPC11D14, LPC1100XL
Abstract
LPC111x/LPC11Cxx User manual

1 Page





UM10398 pdf, ピン配列
NXP Semiconductors
UM10398
LPC111x/LPC11Cxx User manual
Revision history …continued
Rev Date
Description
Modifications:
LPC11D14/PCF8576D block diagram updated (see Figure 5).
Description of interrupt use with IAP calls updated (see Section 26.4.7).
SYSRSTSTAT register access changed to R/W (Table 7).
Frequency values for FREQSEL bits in the WDTOSCCTRL register corrected (see Table 13).
Figure 9 updated (RESET changed to internal reset).
Limit number of bytes copied in Copy RAM to flash ISP and IAP commands for parts with less than
4 kB SRAM (see Table 381 and Table 396).
Figure 14 updated with pseudo open-drain mode.
Part LPC1112FHN24/202 added.
Part IDs added for parts LPC1110FD20, LPC1111FDH20/002, LPC1112FD20/102,
LPC1112FDH20/102, LPC1112FDH28/102, LPC1114FDH28/102, LPC1114FN28/102.
SRAM use by bootloader specified in Section 26.3.1.
8
20120308
LPC111x/LPC11C1x/LPC11C2x User manual
7
20110919
LPC111x/LPC11C1x/LPC11C2x User manual
6
20110822
LPC111x/LPC11C1x/LPC11C2x User manual
5
20110621
LPC111x/LPC11C1x/LPC11C2x User manual
4
20110304
LPC111x/LPC11C1x/LPC11C2x User manual
3
20110114
LPC111x/LPC11C1x/LPC11C2x User manual
2
20101102
LPC111x/LPC11C1x User manual
1
20100721
LPC111x/LPC11C1x User manual
Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
UM10398
User manual
All information provided in this document is subject to legal disclaimers.
Rev. 12.3 — 10 June 2014
© NXP B.V. 2014. All rights reserved.
3 of 547


3Pages


UM10398 電子部品, 半導体
NXP Semiconductors
UM10398
Chapter 1: LPC111x/LPC11Cxx Introductory information
1.2 Features
UM10398
User manual
System:
ARM Cortex-M0 processor, running at frequencies of up to 50 MHz.
ARM Cortex-M0 built-in Nested Vectored Interrupt Controller (NVIC).
Serial Wire Debug.
System tick timer.
Memory:
On-chip flash programming memory for LPC1100, LPC1100L, and LPC1100C
series: 32 kB (LPC1114/LPC11C14), 24 kB (LPC1113), 16 kB
(LPC1112/LPC11C12), or 8 kB (LPC1111), 4kB (LPC1110).
On-chip flash programming memory for LPC1100XL series: 8 kB (LPC1111), 16 kB
(LPC1112), 24 kB (LPC1113), 32 kB (LPC1114/203/303), 48 kB (LPC1114/323),
56 kB (LPC1114/333), 64 kB (LPC1115).
8 kB, 4 kB, 2 kB, or 1 kB SRAM.
In-System Programming (ISP) and In-Application Programming (IAP) via on-chip
bootloader software.
LPC1100XL series only: page erase IAP command.
Digital peripherals:
Up to 42 General Purpose I/O (GPIO) pins with configurable pull-up/pull-down
resistors. Number of GPIO pins is reduced for smaller packages and
LPC11C22/C24.
GPIO pins can be used as edge and level sensitive interrupt sources.
High-current output driver (20 mA) on one pin.
High-current sink drivers (20 mA) on two I2C-bus pins in Fast-mode Plus.
Four general purpose timers/counters with a total of four capture inputs and up to
13 match outputs.
Programmable WatchDog Timer (WDT).
Analog peripherals:
10-bit ADC with input multiplexing among up to 8 pins.
Serial interfaces:
UART with fractional baud rate generation, internal FIFO, and RS-485 support.
Two SPI controllers with SSP features and with FIFO and multi-protocol
capabilities (second SPI on LQFP48 packages only).
I2C-bus interface supporting full I2C-bus specification and Fast-mode Plus with a
data rate of 1 Mbit/s with multiple address recognition and monitor mode.
C_CAN controller (LPC11Cxx only). On-chip CAN and CANopen drivers included.
On-chip, high-speed CAN transceiver (parts LPC11C22/C24 only).
Clock generation:
12 MHz internal RC oscillator trimmed to 1% accuracy that can optionally be used
as a system clock.
Crystal oscillator with an operating range of 1 MHz to 25 MHz.
All information provided in this document is subject to legal disclaimers.
Rev. 12.3 — 10 June 2014
© NXP B.V. 2014. All rights reserved.
6 of 547

6 Page



ページ 合計 : 70 ページ
 
PDF
ダウンロード
[ UM10398 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
UM10398

LPC111x/LPC11Cxx I/O User manual

NXP Semiconductors
NXP Semiconductors


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap