DataSheet.jp

HC125 の電気的特性と機能

HC125のメーカーはMotorola Incです、この部品の機能は「Quad 3-State Noninverting Buffers」です。


製品の詳細 ( Datasheet PDF )

部品番号 HC125
部品説明 Quad 3-State Noninverting Buffers
メーカ Motorola Inc
ロゴ Motorola  Inc ロゴ 




このページの下部にプレビューとHC125ダウンロード(pdfファイル)リンクがあります。

Total 6 pages

No Preview Available !

HC125 Datasheet, HC125 PDF,ピン配置, 機能
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Quad 3-State
Noninverting Buffers
High–Performance Silicon–Gate CMOS
The MC74HC125A and MC74HC126A are identical in pinout to the LS125
and LS126. The device inputs are compatible with standard CMOS outputs;
with pullup resistors, they are compatible with LSTTL outputs.
The HC125A and HC126A noninverting buffers are designed to be used
with 3–state memory address drivers, clock drivers, and other bus–oriented
systems. The devices have four separate output enables that are active–low
(HC125A) or active–high (HC126A).
Output Drive Capability: 15 LSTTL Loads
Outputs Directly Interface to CMOS, NMOS, and TTL
Operating Voltage Range: 2.0 to 6.0 V
Low Input Current: 1.0 µA
High Noise Immunity Characteristic of CMOS Devices
In Compliance with the Requirements Defined by JEDEC Standard
No. 7A
Chip Complexity: 72 FETs or 18 Equivalent Gates
LOGIC DIAGRAM
HC125A
Active–Low Output Enables
HC126A
Active–High Output Enables
A1 2
OE1 1
5
A2
OE2 4
3
Y1
A1
OE1
6
Y2
A2
OE2
2
1
5
4
9
A3
OE3 10
12
A4
13
OE4
8 Y3
A3
11
Y4
OE3
A4
OE4
9
10
12
13
PIN 14 = VCC
PIN 7 = GND
FUNCTION TABLE
HC125A
Inputs Output
A OE Y
HL
LL
XH
H
L
Z
HC126A
Inputs Output
A OE Y
HH
LH
XL
H
L
Z
3 Y1
6
Y2
8 Y3
11
Y4
MC74HC125A
MC74HC126A
N SUFFIX
14–LEAD PLASTIC DIP PACKAGE
CASE 646–06
D SUFFIX
14–LEAD PLASTIC SOIC PACKAGE
CASE 751A–03
DT SUFFIX
14–LEAD PLASTIC TSSOP PACKAGE
CASE 948G–01
ORDERING INFORMATION
MC74HCXXXAN Plastic
MC74HCXXXAD SOIC
MC74HCXXXADT TSSOP
PIN ASSIGNMENT
OE1 1
A1 2
Y1 3
OE2 4
A2 5
Y2 6
GND 7
14 VCC
13 OE4
12 A4
11 Y4
10 OE3
9 A3
8 Y3
4/97
© Motorola, Inc. 1997
1
REV 8

1 Page





HC125 pdf, ピン配列
MC74HC125A MC74HC126A
DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND)
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎSymbol
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎIin
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎIOZ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎICC
Parameter
Maximum Input Leakage Current
Maximum Three–State Leakage
Current
Maximum Quiescent Supply
Current (per Package)
Test Conditions
Vin = VCC or GND
Output in High–Impedance State
Vin = VIL or VIH
Vout = VCC or GND
Vin = VCC or GND
Iout = 0 µA
VCC
V
6.0
6.0
6.0
Guaranteed Limit
v v– 55 to
25_C
85_C
125_C
± 0.1
± 1.0
± 1.0
± 0.5
± 5.0
± 10
Unit
µA
µA
4.0 40 160 µA
NOTE: Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6.0 ns)
Guaranteed Limit
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎSymbol
Parameter
VCC
V
v v– 55 to
25_C
85_C
125_C Unit
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎtPLH,
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎtPHL
Maximum Propagation Delay, Input A to Output Y
(Figures 1 and 3)
2.0 90
3.0 36
4.5 18
6.0 15
115 135 ns
45 60
23 27
20 23
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎtPLZ,
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎtPHZ
Maximum Propagation Delay, Output Enable to Y
(Figures 2 and 4)
2.0 120 150 180 ns
3.0 45 60 80
4.5 24 30 36
6.0 20 26 31
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎtPZL,
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎtPZH
Maximum Propagation Delay, Output Enable to Y
(Figures 2 and 4)
2.0 90
3.0 36
4.5 18
6.0 15
115 135 ns
45 60
23 27
20 23
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎtTLH,
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎtTHL
Maximum Output Transition Time, Any Output
(Figures 1 and 3)
2.0 60 75 90 ns
3.0 22 28 34
4.5 12 15 18
6.0 10 13 15
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎCin MaximumInputCapacitance
— 10 10 10 pF
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎCout
Maximum Three–State Output Capacitance
(Output in High–Impedance State)
— 15 15 15 pF
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎNOTE: For propagation delays with loads other than 50 pF, and information on typical parametric values, see Chapter 2 of the Motorola High–
Speed CMOS Data Book (DL129/D).
Typical @ 25°C, VCC = 5.0 V
CPD
Power Dissipation Capacitance (Per Buffer)*
30 pF
* Used to determine the no–load dynamic power consumption: PD = CPD VCC2f + ICC VCC. For load considerations, see Chapter 2 of the
Motorola High–Speed CMOS Data Book (DL129/D).
High–Speed CMOS Logic Data
DL129 — Rev 6
3
MOTOROLA


3Pages


HC125 電子部品, 半導体
MC74HC125A MC74HC126A
OUTLINE DIMENSIONS
DT SUFFIX
PLASTIC TSSOP PACKAGE
CASE 948G–01
ISSUE O
0.15 (0.006) T U S
2X L/2 14
L
PIN 1
IDENT.
1
14X K REF
0.10 (0.004) M T U S V S
8
B
–U–
7
N 0.25 (0.010)
M
N
F
DETAIL E
0.15 (0.006) T U S
A
–V–
K
ÇÇÇÉÉÇÇÇÉÉÇÇÇÉÉJ J1
K1
SECTION N–N
0.10 (0.004)
–T– SEATING
PLANE
D
C
G
H DETAIL E
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH,
PROTRUSIONS OR GATE BURRS. MOLD FLASH
OR GATE BURRS SHALL NOT EXCEED 0.15
(0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED
0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN
EXCESS OF THE K DIMENSION AT MAXIMUM
MATERIAL CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE DETERMINED
AT DATUM PLANE –W–.
–W–
MILLIMETERS
INCHES
DIM MIN MAX MIN MAX
A 4.90 5.10 0.193 0.200
B 4.30 4.50 0.169 0.177
C ––– 1.20 ––– 0.047
D 0.05 0.15 0.002 0.006
F 0.50 0.75 0.020 0.030
G 0.65 BSC
0.026 BSC
H 0.50 0.60 0.020 0.024
J 0.09 0.20 0.004 0.008
J1 0.09 0.16 0.004 0.006
K 0.19 0.30 0.007 0.012
K1 0.19 0.25 0.007 0.010
L 6.40 BSC
0.252 BSC
M 0_ 8_ 0_ 8_
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
How to reach us:
USA / EUROPE / Locations Not Listed: Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447
Mfax is a trademark of Motorola, Inc.
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 81–3–3521–8315
Mfax: [email protected] – TOUCHTONE 602–244–6609
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
– US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
INTERNET: http://www.mot.com/SPS/
MOTOROLA
6
MC74HC125A/D
High–Speed CMOS Logic Data
DL129 — Rev 6

6 Page



ページ 合計 : 6 ページ
 
PDF
ダウンロード
[ HC125 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
HC120301G-VA

LCD module

HTDisplay
HTDisplay
HC123

Dual Retriggerable Monostable Multivibrator

National Semiconductor
National Semiconductor
HC123

Dual retriggerable monostable multivibrator with reset

NXP Semiconductors
NXP Semiconductors
HC123

DUAL RETRIGGERABLE MONOSTABLE MULTIVIBRATOR

STMicroelectronics
STMicroelectronics


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap