DataSheet.jp

SS49 の電気的特性と機能

SS49のメーカーはHoneywellです、この部品の機能は「Analog Position Sensors」です。


製品の詳細 ( Datasheet PDF )

部品番号 SS49
部品説明 Analog Position Sensors
メーカ Honeywell
ロゴ Honeywell ロゴ 




このページの下部にプレビューとSS49ダウンロード(pdfファイル)リンクがあります。

Total 4 pages

No Preview Available !

SS49 Datasheet, SS49 PDF,ピン配置, 機能
Installation Instructions for the
SS49/SS19 Series Analog Position Sensors
ISSUE 2
PK 88740
PERSONAL INJURY
DO NOT USE these products as safety or
emergency stop devices, or in any other
application where failure of the product could
result in personal injury.
Failure to comply with these instructions could
result in death or serious injury.
SS49/SS19 ELECTRICAL CHARACTERISTICS
Supply Voltage
4 to 10 VDC
Supply Current
4 mA typ.
Output Type
Analog Sourcing
Output Voltage @ 0
Gauss, 25°C
1.75 to 2.25 V @ 5 V
Sensitivity (measured Min. Typ. Max.
between -400 and +400 0.60 0.90 1.25
gauss), mV/G
Operating Temperature -40 to +100°C (-40 to 212°F)
ABSOLUTE MAXIMUM RATINGS
Supply Voltage (Vs)
± 12 VDC
Output Current
20 mA
Storage Temperature
-55 to +150°C (-67 to
+302°F)
Magnetic Flux
No limit. Circuit cannot be
damaged by magnetic
overdrive.
Absolute maximum ratings are the extreme limits
the device will withstand without damage to the
device. However, the electrical and mechanical
characteristics are not guaranteed as the maximum
limits (above recommended operating conditions)
are approached, nor will the device necessarily
operate at absolute maximum ratings.
SOLDERING/ASSEMBLY
SS49
Support leads during any forming/shearing
operation. Do not stress leads inside plastic case.
Hand soldering - Use 60/40 rosin core solder,
and a 399°C (750°F) controlled temperature, 1/8
chisel tip soldering iron. Do not hold iron on
terminals for more than four seconds. Lead
temperature at package must not exceed 250°C
(482°F).
Wave soldering - Use Loncoflux 106A35 or
equivalent. Set preheaters at 95°C (200°F) for top
(component side) of PC board just prior to entering
wave. (This may be adjusted depending upon
board thickness.) Set solder temperature at 252°C
to 260°C max. (485°F to 500°F). Set conveyor
speed to about 4.5 feet per minute (1,37
meter/min.), choosing a speed which gives full
solder fillets and minimum bridging and icicles.
Provide rigid support for the board.
SS19/SS19T
MICRO SWITCH recommends an infrared reflow
process with peak temperatures not to exceed 190 -
200°C (374 - 392°F) for 10 seconds maximum.
Keep exposure to high temperatures minimal.
CLEANING
Clean appropriately in accordance with applicable
safety procedures. MICRO SWITCH recommends
manual cleaning.
BLOCK DIAGRAM
TRANSFER CHARACTERISTICS
MICRO SWITCH Sensing and Control

1 Page





SS49 pdf, ピン配列
SS49/SS19 Series
MOUNTING DIMENSIONS (for reference only)
SS49 SERIES
ISSUE 2 PK 88740
SS19 SERIES
For application help: call 1-800-537-6945
Honeywell MICRO SWITCH Sensing and Control 3


3Pages





ページ 合計 : 4 ページ
 
PDF
ダウンロード
[ SS49 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
SS400

(SS400 Series) Interactive Catalog Replaces Catalog Pages

HONEYWELL
HONEYWELL
SS4000-E

Entry Storage System User Guide

Intel
Intel
SS4001

(SS4001 - SS4007) 1.0 AMP SURFACE MOUNT SILICON RECTIFIERS

GW
GW
SS4002

(SS4001 - SS4007) 1.0 AMP SURFACE MOUNT SILICON RECTIFIERS

GW
GW


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap