|
|
PDF INK1003 Data sheet ( Hoja de datos )
| Número de pieza | INK1003 | |
| Descripción | 3-Channel constant current LED driver | |
| Fabricantes | Greeled Electronic | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de INK1003 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
Greeled Electronic Ltd
INK1003 IC (256-Gray Level)
Data Sheet Of INK1003 IC Driver
Characteristics
Applications
z 3-Channel constant current LED driver.
z Output current won’t vary with the driving z LED decorative lighting
output voltage.
z Digital Dream Color Led Strip Light
z Wide operating voltage:3.3~5.4V
z Indoor/Outdoor LED video or massage display
z High gray level, 256 gray levels.
z PWM signal generator
z Polarity reverse function makes INK1003 z All kinds of LED point light source
suitable for high power full color LED
z LED strips operate between 5~12V
lighting.
z Low output current deviation:
Between channels in a single chip: ±1 %；
Between chips: ±3%；
z Data frequency range wide: 400~800KHz
z Schmitt trigger input
z High reliability, ESD susceptibility high:
HBM 8KV
Greeled Electronic LtdGeneralDescription
INK1003 is a constant current LED driver. It is a single line 3-Channel 256 Grey Level Driver.It is
designed for indoor/ outdoor LED displays and decorative LED lighting system. It is suitable for LED
cascading applications. The INK1003 owns 3 output channels, each channel can sink 18.6mA constant
current. INK1003 contains single line data transceiver decoder, data latches, output registers, band gap
reference voltage generator, internal oscillator, and low saturation constant current sinks. The data received
by INK1003 is decoded and then the decoded data is transferred in to the gray level comparator. The output of
the gray level comparator controls the constant output current.
The output polarity reverse function is designed for driving high power LED by adapting the application
circuitry. The single line control scheme reduces the engineering troubles mostly, the special designed input
and output staged of INK1003, make INK1003 survive during output and input pin short with power source or
GND. When 800KHz, it can achieve 1024Pixels cascade connection.
INK1003 is available in both SOP-8 and DIP-8 packages, the operating temperature is -40~85℃.
PIN CONFIGURATION
TYPICAL APPLICATION CIRCUIT
Fig1 SOP-8
www.gree-leds.com
1
1 page  
Greeled Electronic Ltd
INK1003 IC (256-Gray Level)
Gray Scale Data Word Format
INK1003 uses the one-line communication mode, with return to zero code gray scale data
transport. When the SDI node receives total 24 bit data, SDO node begins to send data to the next chip (set low
before sending) . After that the IC no longer receives data, 3 PWM output named ROUT、GOUT、BOUT outputs
signal with different duty according to the data received. The period of output signal is 3.2mS.The chip receives
data again until RESET signal is sent to SDI node of the IC. Then the SDI node receives total 24 bit data, SDO
node begins to send data to the next IC again. The output of ROUT、ROUT、BOUT will not change until receiving
RESET signal. After the RESET signal( more than 24uS low signal) , 24 bit PWM data received newly will output
to ROUT、GOUT、BOUT.
Automatic shaping forwarding technology is utilized, so the number of cascade is not affected by the signal
transmission, but only affected by refresh speed. A n example of 1024 cascade, whose refresh time is
1024X0.4X2＝0.8192ms, There will be no flicker phenomenon.
During data transfer, the first bit is the MSB of the ROUT channel, the last one transferred into the data shift
register is the LSB of the BOUT channel.
The current duty of each channel of as bellow:
Greeled Electronic LtdDXOUT
=
L[7]* 27
+ L[6]* 26
+ L[5]* 25
+
L[4]* 24 + L[3]* 23
256
+
L[2]* 22
+
L[1]* 21
+ L[0] ----- (7)
Where L[x]=”0” or “1”, which is R、G、B[x], x=0,1,2……7 in the gray scale data. Gray scale data
0000 0000 is for the minimum 0 duty ratio, and 1111 1111 is for the maximum duty ratio.
INK1003 Communication Protocol
24 BIT DATA FORMATE
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
NOTE: MSB is sent first, LSB is sent last. In order to send data ROUT, GOUT, BOUT.
www.gree-leds.com
5
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet INK1003.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| INK1002 | RGB LED | Greeled Electronic |
| INK1003 | 3-Channel constant current LED driver | Greeled Electronic |
| INK1003 | 3-Channel LED driver |  CrossChip |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |