|
|
PDF SM02BS Data sheet ( Hoja de datos )
| Número de pieza | SM02BS | |
| Descripción | IEEE 802.11 b/g/n 2.4GHz 1T1R WiFi | |
| Fabricantes | ETC | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SM02BS (archivo pdf) en la parte inferior de esta página. Total 11 Páginas | ||
|
No Preview Available !
SPECIFICATION
IEEE 802.11 b/g/n 2.4GHz 1T1R WiFi with Bluetooth2.1
/3.0/4.0,and FM CONTROLLER with SDIO INTERFACE, and
HS-UART MIXED INTERFACE
SM02BS (Realtek RTL8723BS)
Combo Module
Version 1.1
1 page  
Operating Channel
WiFi 2.4GHz:
11: (Ch. 1-11) – United States
13: (Ch. 1-13) – Europe
14: (Ch. 1-14) – Japan
BT 2.4GHz:
Ch. 0 ~78
Frequency Range
Transmit Output Power – 1x1
(Tolerance:±1.5dBm)
Receiver Sensitivity
2.400GHz ~ 2.4835 GHz
802.11b@11Mbps
16dBm
BT:
Max +10dBm
802.11g@6Mbps
15dBm
802.11g@54Mbps
14dBm
802.11n
13dBm (MCS 0_HT20)
13dBm (MCS 7_HT20)
12dBm (MCS 0_HT40)
12dBm (MCS 7_HT40)
802.11b@11Mbps
-82dBm
802.11g@54Mbps
-71dBm
802.11n
-67dBm (MCS 7_HT20)
-64dBm (MCS 7_HT40)
BT:
-89dBm@1Mbps, -90dBm@2Mbps, -83dBm@3Mbps
Security
WiFi :
WPA, WPA-PSK, WPA2, WPA2-PSK, WEP 64bit & 128bit, IEEE
802.11x, IEEE 802.11i
BT:
Simple Paring
Operating Voltage
OS supported
3.3 V ±9% I/O supply voltage
Linux/Android
Power Consumption (3.3V)
(Typical)
WiFi only
TX Mode: (Conituous mode)
85mA (MCS7/BW40/13dBm)
RX Mode: (Conituous mode)
75mA (MCS7/BW40/-60dBm)
Associated Idle with DTIM=1
2.1mA
Unassociated Idle:
0.1mA
RF disable Mode:
0.1mA
BT :
Inquiry & Page Scan:
0.9 mA
ACL no traffic:
7.5mA
SCO HV3:
15mA
5 Page 
Wireless module before the SMT note:
Wifi 模块贴片装机前注意事项：
1.When customers Open stencil must be sure the hole bigger to the
Wireless module plate, please press 1 to 1 and 0.7 mm is widened
to open outward, the thickness of 0.12 mm.
2.Can't get the wifi module bare hands when needs,must we wear
the gloves and static ring.
3.The furnace temperature according to the size of the customer the
mainboard ,generally like to stick on a tablet standard temperature
of 250 + - 5,can do 260 + - 5.
1.客户在开钢网时一定要将 wifi 模块焊盘的孔开大，请按 1 比 1 再向
外扩大 0.7mm 比例开钢网，厚度按 0.12mm.
2.有需要拿 wifi 模块时不可以光手去拿，一定要戴上手套以及静电环.
3.过炉温度要根据客户主板的大小而定，一般像平板电脑上的标准温
度为250+-5°，也可以做到260+-5°
Wifi 模块储存及使用管制应注意事项如下：
Storage and use Wifi module control should pay attention to
the following matters:
1.Module of the storage life of vacuum packaging：
1-1.Storage life：12 months. Storage conditions:<40℃. Relative
humidity:<90%R.H.
1-2.After this bag is opened , devices that will be subjected to
infrared reflow, vapor-phase reflow, or equivalent processing must
be :
1-3.Check the humidity card :stored at
≦20%RH.If :30%~40%(pink)or greater than 40%(red).Labeling
module has moisture absorption.
① Mounthed within 168 hours at factory conditions of:
t≦30%℃，≦60%R.H.
② Once opened, the workshop the preservation of life for
168 hours.
1-4.If baking is required,devices may be baked for:
① Modules must be to remove module moisture problem.
② Baking temperature: 125 ℃, 8 hours.
③ After baking, put proper amount of desiccant to seal
packages.
1-5.Module vacuum packing 2000 PCS per disc.
2.Module reel packaging items as follows.
2-1.Storage life：12 months. Storage conditions:<40℃. Relative
humidity:<90%R.H.
2-2.Module apart packing after 168 hours，To launch patch need to
bake, to remove the module hygroscopic, baking temperature
conditions：125℃，8hours.
2-3.Reel packing 2000 PCS or 1000 PCS per disc.
3.Module pallet packaging items as follows：
3-1.Storage life ： 3 months. Storage conditions:<40℃. Relative
humidity:<90%R.H.
3-2.Module if not used within 48 hours, before launch the need for
baking, baking temperature: 125 ℃, 8 hours.
3-3.Pallet packaging each plate is 100 PCS to 1000 PCS or 2000
PCS shipment.
1.模块的真空包装之储存期限：
1-1.保存期限：12个月，储存环境条件：温度在：<40℃，相对湿度：
<90%R.H.
1-2.模块包装被拆后，SMT 组装之时限：
1-3.检查湿度卡：显示值应小于30%（蓝色），如：30%~40%(粉红色）
或者大于40%（红色）表示模块已吸湿气.
① 工厂环境温度湿度管制：≦30%℃，≦60%R.H。
② 拆封后，车间的保存寿命为 168 小时.
1-4.如在拆封后的 168 个小时内未使用完，需要烘烤，烘烤条件如下：
① 模块须重新烘烤，以除去模块吸湿问题.
② 烘烤温度条件：125℃，8 小时.
③ 烘烤后，放入适量的干燥剂再密封包装.
1-5.模块真空包装每盘 2000pcs，真空包装图片<1>
2.模块卷盘包装事项如下：
2-1.保存期限：12个月，储存环境条件：温度在：<40℃，相对湿度：
<90%R.H.
2-2.模块拆开包装168小时后，如要上线贴片需要重新烘烤，以除去模
块吸湿问题，烘烤温度条件：125℃，8小时。
2-3.卷盘包装标准为每盘 2000pcs，也可以 1000pcs.
3.模块托盘包装事项如下：
3-1.保存期限：3个月，储存环境条件：温度在：<40℃，相对湿度：
<90%R.H.
3-2.模块如在 48 小时内未使用，在上线之前需要进行烘烤，烘烤温度
条件：125℃，8 小时。
3-3.托盘包装每盘为 100pcs，以 1000pcs 或 2000pcs 出货.
11 Page | ||
| Páginas | Total 11 Páginas | |
| PDF Descargar | [ Datasheet SM02BS.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SM02B-BHLS-1-TB | BHL Connector |  JST |
| SM02B-BHSS-1-TB | BHS Connector | JST |
| SM02B-BHTS-B-TB | BHT Connector | JST |
| SM02B-PASS-* | CONNECTOR | JST |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |