DataSheet.jp

HCTS160KTR の電気的特性と機能

HCTS160KTRのメーカーはIntersil Corporationです、この部品の機能は「Radiation Hardened Synchronous Counter」です。


製品の詳細 ( Datasheet PDF )

部品番号 HCTS160KTR
部品説明 Radiation Hardened Synchronous Counter
メーカ Intersil Corporation
ロゴ Intersil Corporation ロゴ 




このページの下部にプレビューとHCTS160KTRダウンロード(pdfファイル)リンクがあります。
Total 3 pages

No Preview Available !

HCTS160KTR Datasheet, HCTS160KTR PDF,ピン配置, 機能
Data Sheet
HCTS160T
July 1999 File Number 4626.1
Radiation Hardened Synchronous
Counter
Intersil’s Satellite Applications FlowTM (SAF) devices are fully
tested and guaranteed to 100kRAD total dose. These QML
Class T devices are processed to a standard flow intended
to meet the cost and shorter lead-time needs of large
volume satellite manufacturers, while maintaining a high
level of reliability.
The Intersil HCTS160T is a Radiation Hardened High Speed
Presettable BCD Decade Synchronous Counter that
features an asynchronous reset and look-ahead carry logic.
Counting and parallel presetting are accomplished
synchronously with the low-to-high transition of the clock. A
low level on the synchronous parallel enable input, SPE,
disables counting and allows data at the preset inputs, P0 -
P3, to be loaded into the counter. The counter is reset by a
low on the master reset input, MR. Two count enables, PE
and TE are provided for n-bit cascading. TE also controls the
terminal count output, TC. The terminal count output
indicates a maximum count for one clock pulse and is used
to enable the next cascaded stage to count.
Specifications
Specifications for Rad Hard QML devices are controlled by
the Defense Supply Center in Columbus (DSCC). The SMD
numbers listed below must be used when ordering.
Detailed Electrical Specifications for the HCTS160T are
contained in SMD 5962-95742. A “hot-link” is provided from
our website for downloading.
www.intersil.com/spacedefense/newsafclasst.asp
Intersil‘s Quality Management Plan (QM Plan), listing all
Class T screening operations, is also available on our
website.
www.intersil.com/quality/manuals.asp
Ordering Information
ORDERING
NUMBER
PART NUMBER
TEMP.
RANGE
(oC)
5962R9574201TEC
HCTS160DTR
-55 to 125
5962R9574201TXC
HCTS160KTR
-55 to 125
NOTE: Minimum order quantity for -T is 150 units through
distribution, or 450 units direct.
Features
• QML Class T, Per MIL-PRF-38535
• Radiation Performance
- Gamma Dose (γ) 1 x 105 RAD(Si)
- Latch-Up Free Under Any Conditions
- SEP Effective LET No Upsets: >100 MEV-cm2/mg
- Single Event Upset (SEU) Immunity < 2 x 10-9
Errors/Bit-Day (Typ)
• 3 Micron Radiation Hardened SOS CMOS
• Fanout (Over Temperature Range)
- Standard Outputs 10 LSTTL Loads
• Significant Power Reduction Compared to LSTTL ICs
• DC Operating Voltage Range: 4.5V to 5.5V
• LSTTL Input Compatibility
- VIL = 0.8V Max
- VIH = VCC/2 Min
• Input Current Levels Ii 5mA at VOL, VOH
Pinouts
HCTS160DTR (SBDIP), CDIP2-T16
TOP VIEW
MR 1
CP 2
P0 3
P1 4
P2 5
P3 6
PE 7
GND 8
16 VCC
15 TC
14 Q0
13 Q1
12 Q2
11 Q3
10 TE
9 SPE
HCTS160KTR (FLATPACK), CDFP4-F16
TOP VIEW
MR
CP
P0
P1
P2
P3
PE
GND
1 16
2 15
3 14
4 13
5 12
6 11
7 10
89
VCC
TC
Q0
Q1
Q2
Q3
TE
SPE
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
Satellite Applications Flow™ (SAF) is a trademark of Intersil Corporation.

1 Page





HCTS160KTR pdf, ピン配列
Die Characteristics
DIE DIMENSIONS:
(2642µm x 2184µm x 533µm ±51.0µm)
104 x 86 x 21mils ±2mil
METALLIZATION:
Type: Al Si
Thickness: 11.0kÅ ±1kÅ
SUBSTRATE POTENTIAL:
Unbiased Silicon on Sapphire
BACKSIDE FINISH:
Sapphire
Metallization Mask Layout
P0 (3)
P1 (4)
P2 (5)
P3 (6)
HCTS160T
PASSIVATION:
Type: Silox (SiO2)
Thickness: 13.0kÅ ±2.6kÅ
WORST CASE CURRENT DENSITY:
< 2.0e5 A/cm2
TRANSISTOR COUNT:
676
PROCESS:
CMOS SOS
HCTS160T
CD MR
(2) (1)
VCC
(16)
(15) TC
(14) Q0
(13) Q1
(12) Q2
PE (7)
(11) Q3
(8) (9)
GND SPE
(10)
TE
NOTE: The die diagram is a generic plot from a similar HCS device. It is intended to indicate approximate die size and bond pad location. The mask
series for the HCTS160 is TA14445A.
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time with-
out notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
3


3Pages





ページ 合計 : 3 ページ
 
PDF
ダウンロード
[ HCTS160KTR データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
HCTS160KTR

Radiation Hardened Synchronous Counter

Intersil Corporation
Intersil Corporation


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap