DataSheet.jp

HCTS08DMSR の電気的特性と機能

HCTS08DMSRのメーカーはIntersil Corporationです、この部品の機能は「Radiation Hardened Quad 2-Input AND Gate」です。


製品の詳細 ( Datasheet PDF )

部品番号 HCTS08DMSR
部品説明 Radiation Hardened Quad 2-Input AND Gate
メーカ Intersil Corporation
ロゴ Intersil Corporation ロゴ 




このページの下部にプレビューとHCTS08DMSRダウンロード(pdfファイル)リンクがあります。

Total 10 pages

No Preview Available !

HCTS08DMSR Datasheet, HCTS08DMSR PDF,ピン配置, 機能
HCTS08MS
August 1995
Radiation Hardened
Quad 2-Input AND Gate
Features
Pinouts
• 3 Micron Radiation Hardened SOS CMOS
• Total Dose 200K RAD(Si)
• SEP Effective LET No Upsets: >100 MEV-cm2/mg
• Single Event Upset (SEU) Immunity < 2 x 10-9 Errors/Bit-Day
(Typ)
• Dose Rate Survivability: >1 x 1012 Rads (Si)/Sec
• Dose Rate Upset >1010 RAD(Si)/s 20ns Pulse
• Latch-Up Free Under Any Conditions
• Military Temperature Range: -55oC to +125oC
• Significant Power Reduction Compared to LSTTL ICs
14 LEAD CERAMIC DUAL-IN-LINE
METAL SEAL PACKAGE (SBDIP)
MIL-STD-1835 CDIP2-T14
TOP VIEW
A1 1
B1 2
Y1 3
A2 4
B2 5
Y2 6
GND 7
14 VCC
13 B4
12 A4
11 Y4
10 B3
9 A3
8 Y3
• DC Operating Voltage Range: 4.5V to 5.5V
• LSTTL Input Compatibility
- VIL = 0.8V
- VIH = VCC/2
• Input Current Levels Ii 5µA at VOL, VOH
Description
The Intersil HCTS08MS is a Radiation Hardened Quad 2-Input
AND Gate. A high on both inputs force the output to a High state.
The HCTS08MS utilizes advanced CMOS/SOS technology to
achieve high-speed operation. This device is a member of
radiation hardened, high-speed, CMOS/SOS Logic Family.
The HCTS08MS is supplied in a 14 lead Ceramic Flatpack
Package (K suffix) or a 14 lead SBDIP Package (D suffix).
Ordering Information
A1
B1
Y1
A2
B2
Y2
GND
14 LEAD CERAMIC METAL SEAL
FLATPACK PACKAGE (FLATPACK)
MIL-STD-1835 CDFP3-F14
TOP VIEW
1 14
2 13
3 12
4 11
5 10
69
78
VCC
B4
A4
Y4
B3
A3
Y3
TRUTH TABLE
INPUTS
An Bn
LL
OUTPUTS
Yn
L
PART
NUMBER
TEMPERATURE SCREENING
RANGE
LEVEL
PACKAGE
HCTS08DMSR -55oC to +125oC Intersil Class 14 Lead SBDIP
S Equivalent
HCTS08KMSR -55oC to +125oC Intersil Class 14 Lead Ceramic
S Equivalent Flatpack
HCTS08D/
Sample
+25oC
Sample
14 Lead SBDIP
HCTS08K/
Sample
+25oC
Sample
14 Lead Ceramic
Flatpack
HCTS08HMSR
+25oC
Die
Die
LHL
HL L
HHH
NOTE: L = Logic Level Low, H = Logic level High
Functional Diagram
(1, 4, 9, 12)
An
(2, 5, 10, 13)
Bn
(3, 6, 8, 11)
Yn
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
1
Spec Number 518842
File Number 2136.2

1 Page





HCTS08DMSR pdf, ピン配列
Specifications HCTS08MS
TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS
PARAMETER
Input to Output
SYMBOL
(NOTES 1, 2)
CONDITIONS
TPHL VCC = 4.5V
TPLH VCC = 4.5V
GROUP
A SUB-
GROUPS
9
10, 11
9
10, 11
TEMPERATURE
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
NOTES:
1. All voltages referenced to device GND.
2. AC measurements assume RL = 500, CL = 50pF, Input TR = TF = 3ns, VIL = GND, VIH = 3V.
LIMITS
MIN MAX UNITS
2 18 ns
2 20 ns
2 20 ns
2 22 ns
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS
LIMITS
PARAMETER
Capacitance Power
Dissipation
SYMBOL
CONDITIONS
CPD
VCC = 5.0V, f = 1MHz
Input Capacitance
CIN VCC = 5.0V, f = 1MHz
Output Transition
Time
TTHL
TTLH
VCC = 4.5V
NOTES
1
1
1
1
1
1
TEMPERATURE
+25oC
+125oC, -55oC
+25oC
+125oC
+25oC
+125oC
MIN MAX UNITS
- 45 pF
- 80 pF
- 10 pF
- 10 pF
- 15 ns
- 22 ns
NOTE:
1. The parameters listed in Table 3 are controlled via design or process parameters. Min and Max Limits are guaranteed but not directly
tested. These parameters are characterized upon initial design release and upon design changes which affect these characteristics.
TABLE 4. DC POST RADIATION ELECTRICAL PERFORMANCE CHARACTERISTICS
PARAMETERS
SYMBOL
(NOTES 1, 2)
CONDITIONS
Quiescent Current
ICC VCC = 5.5V, VIN = VCC or GND
Output Current (Sink)
IOL VCC = 4.5V, VIN = VCC or GND,
VOUT = 0.4V
Output Current (Source)
IOH VCC = 4.5V, VIN = VCC or GND,
VOUT = VCC -0.4V
Output Voltage Low
VOL
VCC = 4.5V and 5.5V, VIH = VCC/2,
VIL = 0.8V at 200K RAD,
IOL = 50µA
Output Voltage High
VOH
VCC = 4.5V and 5.5V, VIH = VCC/2,
VIL = 0.8V at 200K RAD,
IOH = -50µA
Input Leakage Current
IIN VCC = 5.5V, VIN = VCC or GND
TEMPERATURE
+25oC
+25oC
200K RAD LIMITS
MIN MAX UNITS
- 0.2 mA
4.0 - mA
+25oC
-4.0 - mA
+25oC
- 0.1 V
+25oC
+25oC
VCC
-0.1
-
V
-5.0 +5.0
µA
Spec Number 518842
3


3Pages


HCTS08DMSR 電子部品, 半導体
HCTS08MS
Intersil Space Level Product Flow - ‘MS’
Wafer Lot Acceptance (All Lots) Method 5007
(Includes SEM)
GAMMA Radiation Verification (Each Wafer) Method 1019,
4 Samples/Wafer, 0 Rejects
100% Nondestructive Bond Pull, Method 2023
Sample - Wire Bond Pull Monitor, Method 2011
Sample - Die Shear Monitor, Method 2019 or 2027
100% Internal Visual Inspection, Method 2010, Condition A
100% Temperature Cycle, Method 1010, Condition C,
10 Cycles
100% Constant Acceleration, Method 2001, Condition per
Method 5004
100% PIND, Method 2020, Condition A
100% External Visual
100% Serialization
100% Initial Electrical Test (T0)
100% Static Burn-In 1, Condition A or B, 24 hrs. min.,
+125oC min., Method 1015
100% Interim Electrical Test 1 (T1)
100% Delta Calculation (T0-T1)
100% Static Burn-In 2, Condition A or B, 24 hrs. min.,
+125oC min., Method 1015
100% Interim Electrical Test 2 (T2)
100% Delta Calculation (T0-T2)
100% PDA 1, Method 5004 (Notes 1and 2)
100% Dynamic Burn-In, Condition D, 240 hrs., +125oC or
Equivalent, Method 1015
100% Interim Electrical Test 3 (T3)
100% Delta Calculation (T0-T3)
100% PDA 2, Method 5004 (Note 2)
100% Final Electrical Test
100% Fine/Gross Leak, Method 1014
100% Radiographic, Method 2012 (Note 3)
100% External Visual, Method 2009
Sample - Group A, Method 5005 (Note 4)
100% Data Package Generation (Note 5)
NOTES:
1. Failures from Interim electrical test 1 and 2 are combined for determining PDA 1.
2. Failures from subgroup 1, 7, 9 and deltas are used for calculating PDA. The maximum allowable PDA = 5% with no more than 3% of the
failures from subgroup 7.
3. Radiographic (X-Ray) inspection may be performed at any point after serialization as allowed by Method 5004.
4. Alternate Group A testing may be performed as allowed by MIL-STD-883, Method 5005.
5. Data Package Contents:
• Cover Sheet (Intersil Name and/or Logo, P.O. Number, Customer Part Number, Lot Date Code, Intersil Part Number, Lot Number, Quan-
tity).
• Wafer Lot Acceptance Report (Method 5007). Includes reproductions of SEM photos with percent of step coverage.
• GAMMA Radiation Report. Contains Cover page, disposition, Rad Dose, Lot Number, Test Package used, Specification Numbers, Test
equipment, etc. Radiation Read and Record data on file at Intersil.
• X-Ray report and film. Includes penetrometer measurements.
• Screening, Electrical, and Group A attributes (Screening attributes begin after package seal).
• Lot Serial Number Sheet (Good units serial number and lot number).
• Variables Data (All Delta operations). Data is identified by serial number. Data header includes lot number and date of test.
• The Certificate of Conformance is a part of the shipping invoice and is not part of the Data Book. The Certificate of Conformance is signed
by an authorized Quality Representative.
Spec Number 518842
6

6 Page



ページ 合計 : 10 ページ
 
PDF
ダウンロード
[ HCTS08DMSR データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
HCTS08DMSR

Radiation Hardened Quad 2-Input AND Gate

Intersil Corporation
Intersil Corporation


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap