DataSheet.jp

HCS283D の電気的特性と機能

HCS283DのメーカーはIntersil Corporationです、この部品の機能は「Radiation Hardened 4-Bit Full Adder with Fast Carry」です。


製品の詳細 ( Datasheet PDF )

部品番号 HCS283D
部品説明 Radiation Hardened 4-Bit Full Adder with Fast Carry
メーカ Intersil Corporation
ロゴ Intersil Corporation ロゴ 




このページの下部にプレビューとHCS283Dダウンロード(pdfファイル)リンクがあります。
Total 9 pages

No Preview Available !

HCS283D Datasheet, HCS283D PDF,ピン配置, 機能
HCS283MS
October 1995
Radiation Hardened
4-Bit Full Adder with Fast Carry
Features
Pinouts
• 3 Micron Radiation Hardened SOS CMOS
• Total Dose 200K RAD (Si)
• SEP Effective LET No Upsets: >100 MEV-cm2/mg
• Single Event Upset (SEU) Immunity < 2 x 10-9 Errors/Bit-
Day (Typ)
• Dose Rate Survivability: >1 x 1012 RAD (Si)/s
• Dose Rate Upset >1010 RAD (Si)/s 20ns Pulse
• Latch-Up Free Under Any Conditions
• Military Temperature Range: -55oC to +125oC
• Significant Power Reduction Compared to LSTTL ICs
16 LEAD CERAMIC DUAL-IN-LINE
METAL SEAL PACKAGE (SBDIP)
MIL-STD-1835 CDIP2-T16, LEAD FINISH C
TOP VIEW
SE 1 1
B1 2
A1 3
S0 4
A0 5
B0 6
CIN 7
GND 8
16 VCC
15 B2
14 A2
13 S2
12 A3
11 B3
10 S3
9 C0
• DC Operating Voltage Range: 4.5V to 5.5V
• Input Logic Levels
- VIL = 30% VCC Max
- VIH = 70% VCC Min
• Input Current Levels Ii 5µA at VOL, VOH
Description
The Intersil HCS283MS is a Radiation Hardened 4-bit binary full
adder with fast carry that adds two 4-bit binary numbers and
generates a carry-out bit if the sum exceeds 15.
The device can be used in positive or negative logic. When using
positive logic the carry-in (CIN) input must be tied low, if there is
no carry-in signal.
The HCS283MS utilizes advanced CMOS/SOS technology to
achieve high-speed operation. This device is a member of
radiation hardened, high-speed, CMOS/SOS Logic Family.
The HCS283MS is supplied in a 16 lead Ceramic flatpack
(K suffix) or a SBDIP Package (D suffix).
16 LEAD CERAMIC METAL SEAL
FLATPACK PACKAGE (FLATPACK)
MIL-STD-1835 CDFP4-F16, LEAD FINISH C
TOP VIEW
SE 1
B1
A1
S0
A0
B0
CIN
GND
1 16
2 15
3 14
4 13
5 12
6 11
7 10
89
VCC
B2
A2
S2
A3
B3
S3
C0
Ordering Information
PART NUMBER
HCS283DMSR
HCS283KMSR
HCS283D/Sample
HCS283K/Sample
HCS283HMSR
TEMPERATURE RANGE
-55oC to +125oC
-55oC to +125oC
+25oC
+25oC
+25oC
SCREENING LEVEL
Intersil Class S Equivalent
Intersil Class S Equivalent
Sample
Sample
Die
PACKAGE
16 Lead SBDIP
16 Lead Ceramic Flatpack
16 Lead SBDIP
16 Lead Ceramic Flatpack
Die
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999
1
Spec Number 518850
File Number 4057

1 Page





HCS283D pdf, ピン配列
Specifications HCS283MS
Absolute Maximum Ratings
Reliability Information
Supply Voltage (VCC). . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +7.0V
Input Voltage Range, All Inputs . . . . . . . . . . . . .-0.5V to VCC +0.5V
DC Input Current, Any One Input . . . . . . . . . . . . . . . . . . . . . . . .±10mA
DC Drain Current, Any One Output. . . . . . . . . . . . . . . . . . . . . . .±25mA
(All Voltage Reference to the VSS Terminal)
Storage Temperature Range (TSTG) . . . . . . . . . . . -65oC to +150oC
Lead Temperature (Soldering 10sec) . . . . . . . . . . . . . . . . . . +265oC
Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1
Thermal Resistance
θJA θJC
SBDIP Package. . . . . . . . . . . . . . . . . . . . 73oC/W 24oC/W
Ceramic Flatpack Package . . . . . . . . . . . 114oC/W 29oC/W
Maximum Package Power Dissipation at +125oC Ambient
SBDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.68W
Ceramic Flatpack Package . . . . . . . . . . . . . . . . . . . . . . . . . 0.44W
If device power exceeds package dissipation capability, provide heat
sinking or derate linearly at the following rate:
SBDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.7mW/oC
Ceramic Flatpack Package . . . . . . . . . . . . . . . . . . . . . . 8.8mW/oC
CAUTION: As with all semiconductors, stress listed under “Absolute Maximum Ratings” may be applied to devices (one at a time) without resulting in permanent
damage. This is a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. The conditions listed
under “Electrical Performance Characteristics” are the only conditions recommended for satisfactory device operation..
Operating Conditions
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V
Input Rise and Fall Times at 4.5V VCC (TR, TF) . . . . . . .100ns Max
Operating Temperature Range (TA) . . . . . . . . . . . . -55oC to +125oC
Input Low Voltage (VIL). . . . . . . . . . . . . . . . . . . 0.0V to 30% of VCC
Input High Voltage (VIH) . . . . . . . . . . . . . . . . . . 70% of VCC to VCC
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS
PARAMETER
Supply Current
SYMBOL
(NOTE 1)
CONDITIONS
ICC VCC = 5.5V,
VIN = VCC or GND
Output Current
(Sink)
Output Current
(Source)
Output Voltage Low
Output Voltage High
Input Leakage
Current
IOL
IOH
VOL
VOH
IIN
VCC = 4.5V, VIH = 4.5V,
VOUT = 0.4V, VIL = 0V ,
Note 2
VCC = 4.5V, VIH = 4.5V,
VOUT = VCC -0.4V,
VIL = 0V, Note 2
VCC = 4.5V, VIH = 3.15V,
IOL = 50µA, VIL = 1.35V
VCC = 5.5V, VIH = 3.85V,
IOL = 50µA, VIL = 1.65V
VCC = 4.5V, VIH = 3.15V,
IOH = -50µA, VIL = 1.35V
VCC = 5.5V, VIH = 3.85V,
IOH = -50µA, VIL = 1.65V
VCC = 5.5V, VIN = VCC or
GND
Noise Immunity
Functional Test
FN VCC = 4.5V, VIH = 3.15V,
VIL = 1.35V, (Note 3)
GROUP
A SUB-
GROUPS
1
2, 3
1
2, 3
1
2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1
2, 3
7, 8A, 8B
TEMPERATURE
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
+25oC, +125oC, -55oC
+25oC, +125oC, -55oC
+25oC, +125oC, -55oC
+25oC, +125oC, -55oC
+25oC
+125oC, -55oC
+25oC, +125oC, -55oC
NOTES:
1. All voltages reference to device GND.
2. Force/measure functions may be interchanged.
3. For functional tests, VO 4.0V is recognized as a logic “1”, and VO 0.5V is recognized as a logic “0”.
LIMITS
MIN MAX
- 40
- 750
4.8 -
4.0 -
-4.8 -
-4.0 -
- 0.1
- 0.1
VCC
-0.1
VCC
-0.1
-
-
-
-
-
±0.5
±5.0
-
UNITS
µA
µA
mA
mA
mA
mA
V
V
V
V
µA
µA
V
Spec Number 518850
3


3Pages


HCS283D 電子部品, 半導体
Specifications HCS283MS
TABLE 6. APPLICABLE SUBGROUPS
CONFORMANCE GROUPS
METHOD
GROUP A SUBGROUPS
Initial Test (Preburn-In)
100%/5004
1, 7, 9
Interim Test I (Postburn-In)
100%/5004
1, 7, 9
Interim Test II (Postburn-In)
100%/5004
1, 7, 9
PDA
100%/5004
1, 7, 9, Deltas
Interim Test III (Postburn-In)
100%/5004
1, 7, 9
PDA
100%/5004
1, 7, 9, Deltas
Final Test
100%/5004
2, 3, 8A, 8B, 10, 11
Group A (Note 1)
Sample/5005
1, 2, 3, 7, 8A, 8B, 9, 10, 11
Group B
Subgroup B-5
Sample/5005 1, 2, 3, 7, 8A, 8B, 9, 10, 11, Deltas
Subgroup B-6
Sample/5005
1, 7, 9
Group D
Sample/5005
1, 7, 9
NOTE:
1. Alternate group A inspection in accordance with Method 5005 of MIL-STD-883 may be exercised.
READ AND RECORD
ICC, IOL/H
ICC, IOL/H
ICC, IOL/H
ICC, IOL/H
Subgroups 1, 2, 3, 9, 10, 11
TABLE 7. TOTAL DOSE IRRADIATION
CONFORMANCE
GROUPS
METHOD
PRE RAD
Group E Subgroup 2
5005
1, 7, 9
NOTE:
1. Except FN test which will be performed 100% Go/No-Go.
TEST
POST RAD
Table 4
READ AND RECORD
PRE RAD
POST RAD
1, 9 Table 4 (Note 1)
TABLE 8. STATIC AND DYNAMIC BURN-IN TEST CONNECTIONS
OPEN
GROUND
1/2 VCC = 3V ± 0.5V VCC = 6V ± 0.5V
STATIC BURN-IN I TEST CONNECTIONS (Note 1)
1, 4, 9, 10, 13
2, 3, 5 - 8, 11, 12, 14, 15
-
16
STATIC BURN-IN II TEST CONNECTIONS (Note 1)
1, 4, 9, 10, 13
8
- 2, 3, 5 - 7, 11, 12,
14, 15, 16
DYNAMIC BURN-IN TEST CONNECTIONS (Note 2)
-
8
1, 4, 9, 10, 13
16
NOTES:
1. Each pin except VCC and GND will have a resistor of 10kΩ ± 5% for static burn-in
2. Each pin except VCC and GND will have a resistor of 1kΩ ± 5% for dynamic burn-in
OSCILLATOR
50kHz
25kHz
--
--
2, 6, 7, 11, 15
3, 5, 12, 14
TABEL 9. IRRADIATION TEST CONNECTIONS (TA = +25oC, ±5oC)
OPEN
GROUND
VCC = 5V ± 0.5V
1, 4, 9, 10, 13
8
2, 3, 5 - 7, 11, 12, 14 - 16
NOTE: Each pin except VCC and GND will have a resistor of 47KΩ ± 5% for irradiation testing.
Group E, Subgroup 2, sample size is 4 dice/wafer 0 failures.
Spec Number 518850
6

6 Page



ページ 合計 : 9 ページ
 
PDF
ダウンロード
[ HCS283D データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
HCS283D

Radiation Hardened 4-Bit Full Adder with Fast Carry

Intersil Corporation
Intersil Corporation
HCS283DMSR

Radiation Hardened 4-Bit Full Adder with Fast Carry

Intersil Corporation
Intersil Corporation
HCS283HMSR

Radiation Hardened 4-Bit Full Adder with Fast Carry

Intersil Corporation
Intersil Corporation
HCS283K

Radiation Hardened 4-Bit Full Adder with Fast Carry

Intersil Corporation
Intersil Corporation


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap