DataSheet.jp

HCS20DMSR の電気的特性と機能

HCS20DMSRのメーカーはIntersil Corporationです、この部品の機能は「Radiation Hardened Dual 4-Input NAND Gate」です。


製品の詳細 ( Datasheet PDF )

部品番号 HCS20DMSR
部品説明 Radiation Hardened Dual 4-Input NAND Gate
メーカ Intersil Corporation
ロゴ Intersil Corporation ロゴ 




このページの下部にプレビューとHCS20DMSRダウンロード(pdfファイル)リンクがあります。

Total 8 pages

No Preview Available !

HCS20DMSR Datasheet, HCS20DMSR PDF,ピン配置, 機能
HCS20MS
September 1995
Radiation Hardened
Dual 4-Input NAND Gate
Features
Pinouts
• 3 Micron Radiation Hardened SOS CMOS
• Total Dose 200K RAD (Si)
• SEP Effective LET No Upsets: >100 MEV-cm2/mg
• Single Event Upset (SEU) Immunity < 2 x 10-9 Errors/Bit-Day
(Typ)
• Dose Rate Survivability: >1 x 1012 RAD (Si)/s
• Dose Rate Upset >1010 RAD (Si)/s 20ns Pulse
• Latch-Up Free Under Any Conditions
• Military Temperature Range: -55oC to +125oC
• Significant Power Reduction Compared to LSTTL ICs
14 LEAD CERAMIC DUAL-IN-LINE
METAL SEAL PACKAGE (SBDIP)
MIL-STD-183S CDIP2-T14, LEAD FINISH C
TOP VIEW
A1 1
B1 2
NC 3
C1 4
D1 5
Y1 6
GND 7
14 VCC
13 D2
12 C2
11 NC
10 B2
9 A2
8 Y2
• DC Operating Voltage Range: 4.5V to 5.5V
• Input Logic Levels
- VIL = 30% of VCC Max
- VIH = 70% of VCC Min
14 LEAD CERAMIC METAL SEAL FLATPACK PACKAGE
(FLATPACK) MIL-STD-183S CDFP3-F14, LEAD FINISH C
TOP VIEW
• Input Current Levels Ii 5µA at VOL, VOH
Description
The Intersil HCS20MS is a Radiation Hardened Dual 4-Input
NAND Gate. A low on any input forces the output to a High state.
The HCS20MS utilizes advanced CMOS/SOS technology to
achieve high-speed operation. This device is a member of
radiation hardened, high-speed, CMOS/SOS Logic Family.
A1
B1
NC
C1
D1
Y1
GND
1 14
2 13
3 12
4 11
5 10
69
78
VCC
D2
C2
NC
B2
A2
Y2
The HCS20MS is supplied in a 14 lead Ceramic flatpack (K suffix)
or a SBDIP Package (D suffix).
Ordering Information
PART
NUMBER
TEMPERATURE SCREENING
RANGE
LEVEL
PACKAGE
HCS20DMSR -55oC to +125oC Intersil Class 14 Lead SBDIP
S Equivalent
HCS20KMSR -55oC to +125oC Intersil Class 14 Lead Ceramic
S Equivalent Flatpack
HCS20D/
Sample
+25oC
Sample
14 Lead SBDIP
HCS20K/
Sample
+25oC
Sample
14 Lead Ceramic
Flatpack
HCS20HMSR
+25oC
Die
Die
Functional Diagram
(1, 9)
An
Bn
(2, 10)
(6, 8)
Yn
(4, 12)
Cn
Dn
(5, 13)
TRUTH TABLE
INPUTS
OUTPUTS
An Bn Cn Dn
Yn
LXXX
H
XLXX
H
XXLX
H
XXXL
H
HHHH
L
NOTE: L = Logic Level Low, H = Logic level High, X = Don’t Care
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999
43
Spec Number 518761
File Number 3050.1

1 Page





HCS20DMSR pdf, ピン配列
Specifications HCS20MS
TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS
PARAMETER
Data to Output
SYMBOL
(NOTES 1, 2)
CONDITIONS
TPHL VCC = 4.5V
Data to Output
TPLH VCC = 4.5V
GROUP
A SUB-
GROUPS
9
10, 11
9
10, 11
TEMPERATURE
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
NOTES:
1. All voltages referenced to device GND.
2. AC measurements assume RL = 500, CL = 50pF, Input TR = TF = 3ns, VIL = GND, VIH = VCC.
LIMITS
MIN MAX UNITS
2 18 ns
2 20 ns
2 20 ns
2 22 ns
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS
LIMITS
PARAMETER
Capacitance Power
Dissipation
SYMBOL
CONDITIONS
CPD
VCC = 5.0V, f = 1MHz
Input Capacitance
CIN VCC = 5.0V, f = 1MHz
Output Transition
Time
TTHL
TTLH
VCC = 4.5V
NOTES
1
1
1
1
1
1
TEMPERATURE
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
MIN MAX UNITS
- 38 pF
- 45 pF
- 10 pF
- 10 pF
- 15 ns
- 22 ns
NOTE:
1. The parameters listed in Table 3 are controlled via design or process parameters. Min and Max Limits are guaranteed but not directly
tested. These parameters are characterized upon initial design release and upon design changes which affect these characteristics.
TABLE 4. DC POST RADIATION ELECTRICAL PERFORMANCE CHARACTERISTICS
PARAMETER
Quiescent Current
Output Current (Sink)
Output Current
(Source)
Output Voltage Low
Output Voltage High
Input Leakage Current
SYMBOL
(NOTES 1, 2)
CONDITIONS
ICC VCC = 5.5V, VIN = VCC or GND
IOL VCC = 4.5V, VIN = VCC or GND,
VOUT = 0.4V
IOH VCC = 4.5V, VIN = VCC or GND,
VOUT = VCC -0.4V
VOL
VCC = 4.5V and 5.5V, VIH = 0.70(VCC),
VIL = 0.30(VCC), IOL = 50µA
VOH
VCC = 4.5V and 5.5V, VIH = 0.70(VCC),
VIL = 0.30(VCC), IOH = -50µA
IIN VCC = 5.5V, VIN = VCC or GND
TEMPERATURE
+25oC
+25oC
200K RAD
LIMITS
MIN MAX UNITS
- 0.2 mA
4.0 - mA
+25oC
-4.0 - mA
+25oC
- 0.1 V
+25oC
+25oC
VCC
-0.1
-
-
±5
V
µA
Spec Number 518761
45


3Pages


HCS20DMSR 電子部品, 半導体
HCS20MS
Intersil Space Level Product Flow - ‘MS’
Wafer Lot Acceptance (All Lots) Method 5007
(Includes SEM)
GAMMA Radiation Verification (Each Wafer) Method 1019,
4 Samples/Wafer, 0 Rejects
100% Nondestructive Bond Pull, Method 2023
Sample - Wire Bond Pull Monitor, Method 2011
Sample - Die Shear Monitor, Method 2019 or 2027
100% Internal Visual Inspection, Method 2010, Condition A
100% Temperature Cycle, Method 1010, Condition C,
10 Cycles
100% Constant Acceleration, Method 2001, Condition per
Method 5004
100% PIND, Method 2020, Condition A
100% External Visual
100% Serialization
100% Initial Electrical Test (T0)
100% Static Burn-In 1, Condition A or B, 24 hrs. min.,
+125oC min., Method 1015
100% Interim Electrical Test 1 (T1)
100% Delta Calculation (T0-T1)
100% Static Burn-In 2, Condition A or B, 24 hrs. min.,
+125oC min., Method 1015
100% Interim Electrical Test 2 (T2)
100% Delta Calculation (T0-T2)
100% PDA 1, Method 5004 (Notes 1and 2)
100% Dynamic Burn-In, Condition D, 240 hrs., +125oC or
Equivalent, Method 1015
100% Interim Electrical Test 3 (T3)
100% Delta Calculation (T0-T3)
100% PDA 2, Method 5004 (Note 2)
100% Final Electrical Test
100% Fine/Gross Leak, Method 1014
100% Radiographic, Method 2012 (Note 3)
100% External Visual, Method 2009
Sample - Group A, Method 5005 (Note 4)
100% Data Package Generation (Note 5)
NOTES:
1. Failures from Interim electrical test 1 and 2 are combined for determining PDA 1.
2. Failures from subgroup 1, 7, 9 and deltas are used for calculating PDA. The maximum allowable PDA = 5% with no more than 3% of the
failures from subgroup 7.
3. Radiographic (X-Ray) inspection may be performed at any point after serialization as allowed by Method 5004.
4. Alternate Group A testing may be performed as allowed by MIL-STD-883, Method 5005.
5. Data Package Contents:
• Cover Sheet (Intersil Name and/or Logo, P.O. Number, Customer Part Number, Lot Date Code, Intersil Part Number, Lot Number,
Quantity).
• Wafer Lot Acceptance Report (Method 5007). Includes reproductions of SEM photos with percent of step coverage.
• GAMMA Radiation Report. Contains Cover page, disposition, Rad Dose, Lot Number, Test Package used, Specification Numbers, Test
equipment, etc. Radiation Read and Record data on file at Intersil.
• X-Ray report and film. Includes penetrometer measurements.
• Screening, Electrical, and Group A attributes (Screening attributes begin after package seal).
• Lot Serial Number Sheet (Good units serial number and lot number).
• Variables Data (All Delta operations). Data is identified by serial number. Data header includes lot number and date of test.
• The Certificate of Conformance is a part of the shipping invoice and is not part of the Data Book. The Certificate of Conformance is signed
by an authorized Quality Representative.
Spec Number 518761
48

6 Page



ページ 合計 : 8 ページ
 
PDF
ダウンロード
[ HCS20DMSR データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
HCS20DMSR

Radiation Hardened Dual 4-Input NAND Gate

Intersil Corporation
Intersil Corporation


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap