|
|
PDF HCPL-2300500 Data sheet ( Hoja de datos )
| Número de pieza | HCPL-2300500 | |
| Descripción | 8 MBd Low Input Current Optocoupler | |
| Fabricantes | Agilent(Hewlett-Packard) | |
| Logotipo | .gif "Agilent(Hewlett-Packard)"){kind=logo} |
|
Hay una vista previa y un enlace de descarga de HCPL-2300500 (archivo pdf) en la parte inferior de esta página. Total 12 Páginas | ||
|
No Preview Available !
H
8 MBd Low Input Current
Optocoupler
Technical Data
HCPL-2300
Features
• Guaranteed Low Thresholds:
IF = 0.5 mA, VF ≤ 1.5 V
• High Speed: Guaranteed
5 MBd over Temperature
• Versatile: Compatible with
TTL, LSTTL and CMOS
• Efficient 820 nm AlGaAs
LED
• Internal Shield for
Guaranteed Common Mode
Rejection
• Schottky Clamped, Open
Collector Output with
Optional Integrated Pull-Up
Resistor
• Static and Dynamic
Performance Guaranteed
from -40°C to 85°C
• Safety Approval
UL Recognized -2500 V rms for
1 minute
CSA Approved
VDE 0884 Approved with
VIORM = 630 V peak
(Option 060)
Applications
• Ground Loop Elimination
• Computer-Peripheral
Interfaces
• Level Shifting
• Microprocessor System
Interfaces
• Digital Isolation for A/D,
D/A Conversion
• RS-232-C Interface
• High Speed, Long Distance
Isolated Line Receiver
Description
The HCPL-2300 optocoupler
combines an 820 nm AlGaAs
photon emitting diode with an
integrated high gain photon
detector. This combination of
Functional Diagram
NC 1
ANODE 2
CATHODE 3
NC 4
Hewlett-Packard designed and
manufactured semiconductor
devices brings new high
performance capabilities to
designers of isolated logic and
data communication circuits.
The new low current, high speed
AlGaAs emitter manufactured
with a unique diffused junction,
has the virtue of fast rise and fall
times at low drive currents.
Figure 6 illustrates the propaga-
tion delay vs. input current
characteristic. These unique
8 VCC
7 RL
6 VOUT
5 GND
A 0.1 pF bypass capacitor must be connected between pins 5 and 8.
CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to
prevent damage and/or degradation which may be induced by ESD.
1-288
5965-3587E
1 page  
VDE 0884 Insulation Related Characteristics (HCPL-2300 Option 060 ONLY)
Description
Installation classification per DIN VDE 0110/1.89, Table 1
for rated mains voltage ≤ 300 V rms
for rated mains voltage ≤ 450 V rms
Climatic Classification
Pollution Degree (DIN VDE 0110/1.89)
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b*
VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec,
Partial Discharge < 5 pC
Input to Output Test Voltage, Method a*
VIORM x 1.5 = VPR, Type and sample test, tm = 60 sec,
Partial Discharge < 5 pC
Highest Allowable Overvoltage*
(Transient Overvoltage, tini = 10 sec)
Safety Limiting Values
(Maximum values allowed in the event of a failure,
also see Figure 11, Thermal Derating curve.)
Case Temperature
Input Current
Output Power
Insulation Resistance at TS, VIO = 500 V
Symbol Characteristic Units
VIORM
VPR
I-IV
I-III
55/85/21
2
630
1181
V peak
V peak
VPR
945
V peak
VIOTM
6000
V peak
TS
IS,INPUT
PS,OUTPUT
RS
175
230
600
≥ 109
°C
mA
mW
Ω
*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section, (VDE 0884), for a
detailed description.
Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in
application.
Absolute Maximum Ratings
(No Derating Required up to 55°C)
Storage Temperature, TS ............................................. -55°C to +125°C
Operating Temperature, TA ........................................... -40°C to +85°C
Lead Solder Temperature, max .......................................... 260°C for 10 s
(1.6 mm below seating plane)
Average Forward Input Current - IF ............................................ 5 mA[2]
Reverse Input Voltage, VR .............................................................. 3.0 V
Supply Voltage, VCC ............................................................... 0 V to 7.0 V
Pull-Up Resistor Voltage, VRL ............................................. -0.5 V to VCC
Output Collector Current, IO ............................................ -25 to 25 mA
Input Power Dissipation, PI ........................................................ 10 mW
Output Collector Power Dissipation, PO ..................................... 40 mW
Output Collector Voltage, VO ........................................... -0.5 V to 18 V
Infrared and Vapor Phase Reflow Temperature
(Option #300) .......................................... see Fig. 1, Thermal Profile
Recommended Operating Conditions
Parameter
Input Voltage, Low Level
Input Current High Level
Supply Voltage, Output
Fan Out (TTL Load)
Operating Temperature
0°C to 85°C
-40°C to 85°C
1-292
Symbol
VFL
IFH
VCC
N
TA
Min.
-2.5
0.5
0.5
4.75
-40
Max.
0.8
1.0
0.75
5.25
5
85
Units
V
mA
V
°C
5 Page 
REFERENCE FIGURE 17 FOR DATA RATE vs. LINE DISTANCE L.
Figure 15. Application of HCPL-2300 as Isolated, Unbalanced Line Receiver(s).
REFERENCE FIGURE 17 FOR DATA RATE vs. LINE DISTANCE L.
Figure 16. Application of Two HCPL-2300 Units Operating as an Isolated, High Speed, Balanced, Split Phase Line
Receiver with Significantly Enhanced Common Mode Immunity.
1-298
11 Page | ||
| Páginas | Total 12 Páginas | |
| PDF Descargar | [ Datasheet HCPL-2300500.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| HCPL-2300500 | 8 MBd Low Input Current Optocoupler | Agilent(Hewlett-Packard) |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |