DataSheet.jp

IR2132S の電気的特性と機能

IR2132SのメーカーはInternational Rectifierです、この部品の機能は「3-PHASE BRIDGE DRIVER」です。


製品の詳細 ( Datasheet PDF )

部品番号 IR2132S
部品説明 3-PHASE BRIDGE DRIVER
メーカ International Rectifier
ロゴ International Rectifier ロゴ 




このページの下部にプレビューとIR2132Sダウンロード(pdfファイル)リンクがあります。

Total 26 pages

No Preview Available !

IR2132S Datasheet, IR2132S PDF,ピン配置, 機能
Data Sheet No. PD60019 Rev.P
IR2130/IR2132(J)(S) & (PbF)
3-PHASE BRIDGE DRIVER
Features
Floating channel designed for bootstrap operation
Fully operational to +600V
Tolerant to negative transient voltage
dV/dt immune
Gate drive supply range from 10 to 20V
Undervoltage lockout for all channels
Over-current shutdown turns off all six drivers
Independent half-bridge drivers
Matched propagation delay for all channels
2.5V logic compatible
Outputs out of phase with inputs
Cross-conduction prevention logic
Also available LEAD-FREE
Description
Product Summary
VOFFSET
600V max.
IO+/-
200 mA / 420 mA
VOUT
10 - 20V
ton/off (typ.)
675 & 425 ns
Deadtime (typ.) 2.5 µs (IR2130)
0.8 µs (IR2132)
Packages
The IR2130/IR2132(J)(S) is a high voltage, high speed
power MOSFET and IGBT driver with three indepen-
dent high and low side referenced output channels. Pro-
prietary HVIC technology enables ruggedized
monolithic construction. Logic inputs are compatible with
28-Lead SOIC
CMOS or LSTTL outputs, down to 2.5V logic. A
ground-referenced operational amplifier provides
28-Lead PDIP
analog feedback of bridge current via an external cur-
rent sense resistor. A current trip function which termi-
nates all six outputs is also derived from this resistor.
44-Lead PLCC w/o 12 Leads
An open drain FAULT signal indicates if an over-cur-
rent or undervoltage shutdown has occurred. The output drivers feature a high pulse current buffer stage designed
for minimum driver cross-conduction. Propagation delays are matched to simplify use at high frequencies. The
floating channels can be used to drive N-channel power MOSFETs or IGBTs in the high side configuration
which operate up to 600 volts.
Typical Connection
(Refer to Lead Assignments for correct pin configuration). This/These diagram(s) show electrical connections only. Please refer
to our Application Notes and DesignTips for proper circuit board layout.
www.irf.com
1

1 Page





IR2132S pdf, ピン配列
IR2130/IR2132(J)(S) & (PbF)
Dynamic Electrical Characteristics
VBIAS (VCC, VBS1,2,3) = 15V, VS0,1,2,3 = VSS, CL = 1000 pF and TA = 25°C unless otherwise specified. The dynamic
electrical characteristics are defined in Figures 3 through 5.
Symbol
Definition
Figure Min. Typ. Max. Units Test Conditions
ton
toff
tr
tf
titrip
tbl
tflt
tflt,in
tfltclr
DT
SR+
SR-
Turn-On Propagation Delay
Turn-Off Propagation Delay
Turn-On Rise Time
Turn-Off Fall Time
ITRIP to Output Shutdown Prop. Delay
ITRIP Blanking Time
ITRIP to FAULT Indication Delay
Input Filter Time (All Six Inputs)
LIN1,2,3 to FAULT Clear Time
Deadtime (IR2130)
(IR2132)
Operational Amplifier Slew Rate (+)
Operational Amplifier Slew Rate (-)
11 500 675 850
12 300 425 550
13 — 80 125
14 — 35 55
VIN = 0 & 5V
VS1,2,3 = 0 to 600V
15 400 660 920
VIN, VITRIP = 0 & 5V
— 400 —
ns
VITRIP = 1V
16 335 590 845
VIN, VITRIP = 0 & 5V
— — 310 —
VIN = 0 & 5V
17 6.0 9.0 12.0
VIN, VITRIP = 0 & 5V
18 1.3 2.5 3.7 µs
18 0.4 0.8 1.2
VIN = 0 & 5V
19 4.4 6.2 —
20 2.4 3.2 — V/µs
NOTE: For high side PWM, HIN pulse width must be ≥ 1.5µsec
Static Electrical Characteristics
VBIAS (VCC, VBS1,2,3) = 15V, VS0,1,2,3 = VSS and TA = 25°C unless otherwise specified. The VIN, VTH and IIN parameters
are referenced to VSS and are applicable to all six logic input leads: HIN1,2,3 & LIN1,2,3 . The VO and IO parameters
are referenced to VS0,1,2,3 and are applicable to the respective output leads: HO1,2,3 or LO1,2,3.
Symbol
VIH
VIL
VIT,TH+
VOH
VOL
ILK
IQBS
IQCC
IIN+
IIN-
IITRIP+
IITRIP-
VBSUV+
VBSUV-
VCCUV+
VCCUV-
Ron,FLT
Definition
Figure Min.
Logic “0” Input Voltage (OUT = LO)
Logic “1” Input Voltage (OUT = HI)
21 2.2
22 —
ITRIP Input Positive Going Threshold
High Level Output Voltage, VBIAS - VO
Low Level Output Voltage, VO
Offset Supply Leakage Current
Quiescent VBS Supply Current
Quiescent VCC Supply Current
Logic “1” Input Bias Current (OUT = HI)
23 400
24 —
25 —
26 —
27 —
28 —
29 —
Logic “0” Input Bias Current (OUT = LO) 30 —
“High” ITRIP Bias Current
31 —
“Low” ITRIP Bias Current
32 —
VBS Supply Undervoltage Positive Going 33 7.5
Threshold
VBS Supply Undervoltage Negative Going
Threshold
34
7.1
VCC Supply Undervoltage Positive Going 35 8.3
Threshold
VCC Supply Undervoltage Negative Going
Threshold
36
8.0
FAULT Low On-Resistance
37 —
Typ. Max. Units Test Conditions
——
V
— 0.8
490 580
— 100 mV
— 100
— 50
15 30 µA
3.0 4.0 mA
450 650
225 400 µA
75 150
VIN = 0V, IO = 0A
VIN = 5V, IO = 0A
VB = VS = 600V
VIN = 0V or 5V
VIN = 0V or 5V
VIN = 0V
VIN = 5V
ITRIP = 5V
— 100
8.35 9.2
nA
ITRIP = 0V
7.95 8.8
9.0 9.7
V
8.7 9.4
55 75
www.irf.com
3


3Pages


IR2132S 電子部品, 半導体
IR2130/IR2132(J)(S) & (PbF)
HIN1,2,3
LIN1,2,3
ITRIP
FAULT
HO1,2,3
LO1,2,3
Figure 1. Input/Output Timing Diagram
<50 V/ns
Figure 2. Floating Supply Voltage Transient Test Circuit
HIN1,2,3
50%
50%
LIN1,2,3
LO1,2,3
HO1,2,3
50%
50%
DT DT
Figure 3. Deadtime Waveform Definitions
HIN1,2,3
LIN1,2,3
50%
50%
ton
HO1,2,3
LO1,2,3
tr
90%
10%
toff tf
90%
10%
Figure 4. Input/Output Switching Time Waveform
Definitions
6 www.irf.com

6 Page



ページ 合計 : 26 ページ
 
PDF
ダウンロード
[ IR2132S データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
IR2132

3-PHASE BRIDGE DRIVER

International Rectifier
International Rectifier
IR2132J

3-PHASE BRIDGE DRIVER

International Rectifier
International Rectifier
IR2132JPBF

3-PHASE BRIDGE DRIVER

International Rectifier
International Rectifier
IR2132PBF

3-PHASE BRIDGE DRIVER

International Rectifier
International Rectifier


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap