|
|
PDF IT8518 Data sheet ( Hoja de datos )
| Número de pieza | IT8518 | |
| Descripción | Programmable DC Electronic Load User Guide Manual | |
| Fabricantes | ITECH | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de IT8518 (archivo pdf) en la parte inferior de esta página. Total 44 Páginas | ||
|
No Preview Available !
USER’S GUIDE
Programmable DC Electronic Load
Models IT8518
This user manual is applicable to:
Model: IT8518B/IT8518C/IT8518E/IT8518F
Copyright 2010 All Rights Reserved
Ver2,0/Jan, 2010/ IT8500-401
http://www.Datasheet4U.com
1 page  
Safety Summary
The following general safety precautions must be observed during all phases of operation
of this instrument. Failure to comply with these precautions or with specific warnings
elsewhere in this manual violates safety standards of design, manufacture, and intended
use of the instrument .We assumes no liability for the customer’s failure to comply with these
requirements.
Environmental Conditions
This instrument is intended for indoor use. Pollution degree 2 environments. It is designed to
operate at a maximum relative humidity of 95% and at altitudes of up to 2000 meters. Refer
to the specifications tables for the ac mains voltage requirements and ambient operating
temperature range.
Before Applying Power
Verify that all safety precautions are taken. Note the instrument's external markings
described under "Safety Symbols".
Ground the Instrument
This product is a Safety Class 1 instrument (provided with a protective earth terminal). To
minimize shock hazard, the instrument chassis and cover must be connected to an electrical
ground. The instrument must be connected to the ac power mains through a grounded
power cable, with the ground wire firmly connected to an electrical ground (safety ground)
at the power outlet. Note: Any interruption of the protective (grounding) conductor or
disconnection of the protective earth terminal will cause a potential shock hazard that could
result in personal injury.
DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE
Do not operate the instrument in the presence of fumes or flammable gases.
KEEP AWAY FROM LIVE CIRCUITS
Operating personnel must not remove instrument covers except as instructed in this Guide
for installing or removing electronic load modules. Component replacement and internal
adjustments must be made only by qualified service personnel. Do not replace components
with power cable connected. Under certain conditions dangerous voltages may exist even
with the power cable removed. To avoid injuries always disconnect power, discharge circuits,
and remove external voltage sources before touching components.
USER’S GUIDE 5
5 Page 
GENERAL INFORMATION
BAUDRATE SET
Setting baud rate.
4800<DEFAULT>
9600
19200
38400
COMM. PARITY SET
Command parity setting.
NONE<DEFAULT>
EVEN
ODD
ADDRESS SET
KEY LOCK SET
Setting communication Flow mode
Setting keypad password.
EXIT
SYSTEM SET
MAX CURRENT SET
MAX POWER SET
MAX VOLTAGE SET
Setup the maximum current.
Setup the maximum power.
Setup the maximum voltage
VOLTAGE ONSET
VOLTAGE OFFSET
EXIT
LIST SET
MODE SET
FIXED MODE
LIST MODE
CALL LIST FILE
EDIT LIST FILE
LIST STORE MODE
Setting operation mode.
Fixed mode.
Choosing List mode.
Recall list operation file.
Edit list operation file.
Users can choose 4 kind of memory space to
save the list file.
8 X 120 STEPS
4 X 250 STEP
2 X 500 STEPS
Total 8 files and each file have120 list steps.
Total 4 files and each file have250 list steps.
Total 2 files and each file have500 list steps
1 X 1000 STEPS
Total 1 file and each file have1000 list steps.
EXIT
LOAD ON TIMER
TIMER STATE
Setting LOAD ON timer state
ON
OFF
When users choose ON, and then turn on the
electronic load input, the LOAD ON TIMER will
start working. When the LOAD ON TIMER is reach
the setup time, the electronic load input will turn
offautomatically.
TIMER SET
EXIT
Setting time of LOAD ON timer.
EXIT
USER’S GUIDE 11
11 Page | ||
| Páginas | Total 44 Páginas | |
| PDF Descargar | [ Datasheet IT8518.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| IT8510E | Embedded Controller |  ITE |
| IT8510G | Embedded Controller | ITE |
| IT8510TE | Embedded Controller | ITE |
| IT8511E | Embedded Controller | ITE |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |