DataSheet.es    


PDF C8051F589 Data sheet ( Hoja de datos )

Número de pieza C8051F589
Descripción Mixed Signal ISP Flash MCU Family
Fabricantes Silicon Laboratories　
Logotipo Silicon Laboratories Logotipo



Hay una vista previa y un enlace de descarga de C8051F589 (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! C8051F589 Hoja de datos, Descripción, Manual

Analog Peripherals
- 12-Bit ADC
• Up to 200 ksps
• Up to 32 external single-ended inputs
• VREF from on-chip VREF, external pin or VDD
• Internal or external start of conversion source
• Built-in temperature sensor
- Three Comparators
• Programmable hysteresis and response time
• Configurable as interrupt or reset source
• Low current
On-Chip Debug
- On-chip debug circuitry facilitates full speed, non-
intrusive in-system debug (no emulator required)
- Provides breakpoints, single stepping,
inspect/modify memory and registers
- Superior performance to emulation systems using
ICE-chips, target pods, and sockets
- Low cost, complete development kit
Supply Voltage 1.8 to 5.25 V
- Typical operating current: 15 mA at 50 MHz;
Typical stop mode current: 230 µA
High-Speed 8051 µC Core
- Pipelined instruction architecture; executes 70% of
instructions in 1 or 2 system clocks
- Up to 50 MIPS throughput with 50 MHz clock
- Expanded interrupt handler
Automotive Qualified
- Temperature Range: –40 to +125 °C
C8051F58x/F59x
Mixed Signal ISP Flash MCU Family
Memory
- 8448 bytes internal data RAM (256 + 8192 XRAM)
- 128 or 96 kB Banked Flash; In-system programma-
ble in 512-byte Sectors
- External 64 kB data memory interface programma-
ble for multiplexed or non-multiplexed mode
Digital Peripherals
- 40, 33, or 25 Port I/O; All 5 V push-pull with high
sink current
- CAN 2.0 Controller—no crystal required
- LIN 2.1 Controller (Master and Slave capable); no
crystal required
- Two Hardware enhanced UARTs, SMBus™, and
enhanced SPI™ serial ports
- Six general purpose 16-bit counter/timers
- Two 16-Bit programmable counter array (PCA)
peripherals with six capture/compare modules each
and enhanced PWM functionality
Clock Sources
- Internal 24 MHz with ±0.5% accuracy for CAN and
master LIN operation.
- External oscillator: Crystal, RC, C, or clock
(1 or 2 pin modes)
- Can switch between clock sources on-the-fly;
useful in power saving modes
Packages
- 48-Pin QFP/QFN (C8051F580/1/4/5)
- 40-Pin QFN (C8051F588/9-F590/1)
- 32-Pin QFP/QFN (C8051F582/3/6/7)
ANALOG
PERIPHERALS
A 12-bit
M
U
200 ksps
X ADC
TEMP
SENSOR
Voltage VREG
Comparators 0-2 VREF
DIGITAL I/O
UART 0-1
SMBus
SPI
PCA x 2
Timers 0-5
CAN
LIN
Ports 0-4
Crossbar
External
Memory
Interface
24 MHz PRECISION
INTERNAL OSCILLATOR
2x Clock Multiplier
HIGH-SPEED CONTROLLER CORE
128 kB
ISP FLASH
FLEXIBLE
INTERRUPTS
8051 CPU
(50 MIPS)
DEBUG
CIRCUITRY
8 kB XRAM
POR WDT
Rev. 1.2 4/11
Copyright © 2011 by Silicon Laboratories C8051F580/1/2/3/4/5/6/7/8/9-F590/1
Free Datasheet http://www.Datasheet4U.com

1 page




C8051F589 pdf
C8051F58x/F59x
18.4.2. Non-multiplexed Configuration.............................................................. 163
18.5. Memory Mode Selection................................................................................ 164
18.5.1. Internal XRAM Only .............................................................................. 164
18.5.2. Split Mode without Bank Select............................................................. 164
18.5.3. Split Mode with Bank Select.................................................................. 165
18.5.4. External Only......................................................................................... 165
18.6. Timing .......................................................................................................... 165
18.6.1. Non-Multiplexed Mode .......................................................................... 167
18.6.1.1. 16-bit MOVX: EMI0CF[4:2] = 101, 110, or 111............................. 167
18.6.1.2. 8-bit MOVX without Bank Select: EMI0CF[4:2] = 101 or 111 ....... 168
18.6.1.3. 8-bit MOVX with Bank Select: EMI0CF[4:2] = 110 ....................... 169
18.6.2. Multiplexed Mode .................................................................................. 170
18.6.2.1. 16-bit MOVX: EMI0CF[4:2] = 001, 010, or 011............................. 170
18.6.2.2. 8-bit MOVX without Bank Select: EMI0CF[4:2] = 001 or 011 ....... 171
18.6.2.3. 8-bit MOVX with Bank Select: EMI0CF[4:2] = 010 ....................... 172
19. Oscillators and Clock Selection ......................................................................... 174
19.1. System Clock Selection................................................................................. 174
19.2. Programmable Internal Oscillator .................................................................. 176
19.2.1. Internal Oscillator Suspend Mode ......................................................... 176
19.3. Clock Multiplier .............................................................................................. 179
19.4. External Oscillator Drive Circuit..................................................................... 181
19.4.1. External Crystal Example...................................................................... 183
19.4.2. External RC Example............................................................................ 184
19.4.3. External Capacitor Example.................................................................. 184
20. Port Input/Output ................................................................................................. 186
20.1. Port I/O Modes of Operation.......................................................................... 188
20.1.1. Port Pins Configured for Analog I/O...................................................... 188
20.1.2. Port Pins Configured For Digital I/O...................................................... 188
20.1.3. Interfacing Port I/O in a Multi-Voltage System ...................................... 189
20.2. Assigning Port I/O Pins to Analog and Digital Functions............................... 189
20.2.1. Assigning Port I/O Pins to Analog Functions ........................................ 189
20.2.2. Assigning Port I/O Pins to Digital Functions.......................................... 189
20.2.3. Assigning Port I/O Pins to External Digital Event Capture Functions ... 190
20.3. Priority Crossbar Decoder ............................................................................. 190
20.4. Port I/O Initialization ...................................................................................... 193
20.5. Port Match ..................................................................................................... 198
20.6. Special Function Registers for Accessing and Configuring Port I/O ............. 202
21. Local Interconnect Network (LIN0)..................................................................... 212
21.1. Software Interface with the LIN Controller..................................................... 213
21.2. LIN Interface Setup and Operation................................................................ 213
21.2.1. Mode Definition ..................................................................................... 213
21.2.2. Baud Rate Options: Manual or Autobaud ............................................. 213
21.2.3. Baud Rate Calculations: Manual Mode................................................. 213
21.2.4. Baud Rate Calculations—Automatic Mode ........................................... 215
21.3. LIN Master Mode Operation .......................................................................... 216
Rev. 1.2
5
Free Datasheet http://www.Datasheet4U.com

5 Page





C8051F589 arduino
C8051F58x/F59x
Figure 27.2. T0 Mode 2 Block Diagram ................................................................. 287
Figure 27.3. T0 Mode 3 Block Diagram ................................................................. 288
Figure 27.4. Timer 2 16-Bit Mode Block Diagram ................................................. 293
Figure 27.5. Timer 2 8-Bit Mode Block Diagram ................................................... 294
Figure 27.6. Timer 2 External Oscillator Capture Mode Block Diagram ................ 295
Figure 27.7. Timer 3 16-Bit Mode Block Diagram ................................................. 299
Figure 27.8. Timer 3 8-Bit Mode Block Diagram ................................................... 300
Figure 27.9. Timer 3 External Oscillator Capture Mode Block Diagram ................ 301
Figure 27.10. Timer 4 and 5 Capture Mode Block Diagram .................................. 306
Figure 27.11. Timer 4 and 5 Auto Reload and Toggle Mode Block Diagram ........ 307
Figure 28.1. PCA0 Block Diagram ......................................................................... 312
Figure 28.2. PCA0 Counter/Timer Block Diagram ................................................. 313
Figure 28.3. PCA0 Interrupt Block Diagram .......................................................... 314
Figure 28.4. PCA0 Capture Mode Diagram ........................................................... 316
Figure 28.5. PCA0 Software Timer Mode Diagram ............................................... 317
Figure 28.6. PCA0 High-Speed Output Mode Diagram ......................................... 318
Figure 28.7. PCA0 Frequency Output Mode ......................................................... 319
Figure 28.8. PCA0 8-Bit PWM Mode Diagram ...................................................... 320
Figure 28.9. PCA0 9, 10 and 11-Bit PWM Mode Diagram .................................... 321
Figure 28.10. PCA0 16-Bit PWM Mode ................................................................. 322
Figure 28.11. PCA0 Module 5 with Watchdog Timer Enabled .............................. 323
Figure 29.1. PCA1 Block Diagram ......................................................................... 331
Figure 29.2. PCA1 Counter/Timer Block Diagram ................................................. 332
Figure 29.3. PCA1 Interrupt Block Diagram .......................................................... 333
Figure 29.4. PCA1 Capture Mode Diagram ........................................................... 335
Figure 29.5. PCA1 Software Timer Mode Diagram ............................................... 336
Figure 29.6. PCA1 High-Speed Output Mode Diagram ......................................... 337
Figure 29.7. PCA1 Frequency Output Mode ......................................................... 338
Figure 29.8. PCA1 8-Bit PWM Mode Diagram ...................................................... 340
Figure 29.9. PCA1 9, 10 and 11-Bit PWM Mode Diagram .................................... 341
Figure 29.10. PCA1 16-Bit PWM Mode ................................................................. 342
Figure 30.1. Typical C2 Pin Sharing ...................................................................... 353
Rev. 1.2
11
Free Datasheet http://www.Datasheet4U.com

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet C8051F589.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
C8051F580Mixed Signal ISP Flash MCU FamilySilicon Laboratories
Silicon Laboratories
C8051F581Mixed Signal ISP Flash MCU FamilySilicon Laboratories
Silicon Laboratories
C8051F582Mixed Signal ISP Flash MCU FamilySilicon Laboratories
Silicon Laboratories
C8051F583Mixed Signal ISP Flash MCU FamilySilicon Laboratories
Silicon Laboratories

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

 Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

 Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar