DataSheet.jp

BR200 の電気的特性と機能

BR200のメーカーはSankenです、この部品の機能は「(BR200 / BR201) POL Converter Module」です。


製品の詳細 ( Datasheet PDF )

部品番号 BR200
部品説明 (BR200 / BR201) POL Converter Module
メーカ Sanken
ロゴ Sanken ロゴ 




このページの下部にプレビューとBR200ダウンロード(pdfファイル)リンクがあります。

Total 12 pages

No Preview Available !

BR200 Datasheet, BR200 PDF,ピン配置, 機能
BR200/201
POL Converter Module for 12 V System Intermediate Bus
Features and Benefits
• Industry standard footprint
• Improved soldering: gold-plated pads and side notches
• Synchronized rectifying type stepdown chopper
• High power
• High efficiency:
BR200, 89.9% at VIN = 12 V, VO = 1.5 V, IO = 7 A
BR201, 93.8% at VIN = 12 V, VO = 3.3 V, IO = 7 A
• Operating temperature range: –40°C to 85°C
• Input voltage range: 7 to 14 VDC
• Output voltage: BR200, 0.75 to 1.65 V; BR201, 1.6 to 3.63 V
• Output current range: 0 to 10 A
• Operating frequency: BR200, 300 kHz; BR201, 600 kHz
• Overcurrent protection function
Package: Module
Description
The BR200 and BR201 are thin type POL converter modules
with an industry standard exterior shape and footprint,
responsive to very high speed loads and compatible with
ceramic capacitors.
They can be used as design-free POL converters for a 12 V
system intermediate bus. They can be configured easily,
reducing overall design time, and allowing reuse of designs.
Miniaturization was achieved by high frequency switching
technology, allowing saving space on the application PCB.
Soldering capability has been significantly improved by
adoption of end face through holes.
20.3 × 11.4 × 4.2 mm
Applications:
• Communication devices
• Computer server
• Other low power conversion
Typical Application Circuit
VPG (5 V)
Power Good
VIN
ON/OFF
GND
BR200/201
ON/OFF VS+
PG VOUT
VIN RTRIM
GND
CIN RTRIM
VOUT
COUT
BR200-DS, Rev. 0.2
February 6, 2013
SANKEN ELECTRIC CO., LTD.
http://www.sanken-ele.co.jp/en/
Free Datasheet http://www.Datasheet4U.com

1 Page





BR200 pdf, ピン配列
BR200/201
POL Converter Module for 12 V System Intermediate Bus
Electrical Characteristics Unless specifically noted, TA is 25°C
Characteristic
Symbol
Test Conditions
Min.
Typ.
Max.
Unit
Input Voltage Range
Output Voltage
VIN
VOUT
BR200
BR201
Adjust with RTRIM
7.0 12.0 14.0 V
0.75 – 1.65 V
1.60 – 3.63 V
Output Current
Output Voltage Accuracy
Ripple Voltage1
Efficiency
Operating Frequency
IOUT
ErrVOUT
Vrip
η
fOP
With temperature derating
VIN = 7 to 14 V, IOUT = 0 to IOUT(max), Operating
Temperature Range, RTRIM =1% accuracy
BR200
BW = 20 MHz, VOUT = 1.5 V,
IOUT = 0 to10 A, COUT = 400 μF
BR201
BW = 20 MHz, VOUT = 3.3 V,
IOUT = 0 to10 A, COUT = 200 μF
BR200 VIN = 12 V, IOUT = 10 A, VOUT = 1.5 V
BR201 VIN = 12 V, IOUT = 10 A, VOUT = 3.3 V
BR200
BR201
0
–2.0
35
5
88.5
93.2
300
600
10 A
2.0 %VOUT
50 mVp-p
50 mVp-p
–%
–%
– kHz
– kHz
Overcurrent Protection Threshold
Input Capacitor2
Output Capacitor2
IOUT(OCP)
CIN
COUT
Hiccup
When input voltage is an ideal voltage source
BR200
BR201
When input voltage is an ideal voltage
source
20
200
200
24.5 –
A
5000
μF
4000
μF
3000
μF
Startup Time
Start Delay Time
BR200
tr BR201 VOUT from 10% to 90% points
– 1.5 – ms
– 1.0 – ms
With the ON/¯O¯¯F¯¯F¯ pin open, measured from the
td VIN pin switching high, to VOUT reaching 10% of
2
– ms
operating level (see figure 1)
ON/¯O¯¯F¯¯F¯ Start Delay Time
With the VIN pin high, measured from the
trcd ON/¯O¯¯F¯¯F¯ pin switching open, to VOUT reaching
2
– ms
10% of operating level (see figure 2)
Interface Characteristics
Power Good
ON/¯O¯¯F¯¯F¯ Pin High Voltage
ON/¯O¯¯F¯¯F¯ Pin Low Voltage
PWGL
PWGH
VIH
VIL
BR200 Lower limit of Power Good
BR201 Lower limit of Power Good
BR200 Upper limit of Power Good
BR201 Upper limit of Power Good
When the ON/¯O¯¯F¯¯F¯ pin is set open, the
BR200/201 converter is turned on
When the ON/¯O¯¯F¯¯F¯ pin is pulled down to GND,
the BR200/201 converter is turned off
83.3
83.1
109.2
109.3
0.55
0.27
87.5
87.3
112.5
112.7
0.70
0.30
91.7
91.5
116.7
116.9
1.00
0.33
%VOUT
%VOUT
%VOUT
%VOUT
V
V
1See the Ripple Voltage Measuring Method section.
2Place bypass capacitors between the VIN and VOUT terminals and GND (see CIN and COUT in the Typical Application Circuit diagram). Locate the
capacitor as close as possible to the terminal.
BR200-DS, Rev. 0.2
SANKEN ELECTRIC CO., LTD.
3
Free Datasheet http://www.Datasheet4U.com


3Pages


BR200 電子部品, 半導体
BR200/201
POL Converter Module for 12 V System Intermediate Bus
Functional Description
Power Good ( PG) Operation
When output voltage, VOUT , is within the Power Good detection
range, the PG pin is disconnected internally by the MOSFET
switch. The signal at the Power Good node is pulled up to 5 V. If
VOUT falls out of the Power Good detection range, the MOSFET
switch connects PG to GND, and the signal at the Power Good
node is pulled low. The PG peripheral circuit is shown in figure 3.
Output Sensing ( VS+) and Compensation
Reduction in output voltage can be compensated by connecting
the output sense terminal, VS+ , to the load. When using LC filter,
the proper connection is shown in panel A of figure 4. Note: Do
not connect the output sense terminal to the output of the LC
filter. It may not operate normally.
CAUTION: When the output sense terminal is not used, it must
be connected directly to the VOUT output terminal. This is shown
in panel B of figure 4.
VPG(5V)
Power Good
GND
Figure 3. PG peripheral circuit
BR200/201
VOUT
(A)
VS+
GND
COUT
BR200/201
PG
GND
L
COL
External On/Off Output Control (ON/¯O¯¯F¯¯F¯)
Operation of the output of the product can be turned on and off by
using the On/Off function, irrespective of input voltage connec-
tion.
This is enabled by connection of the ON/¯O¯¯F¯F pin (pin 1) (refer
to figure 5):
• When the ON/¯O¯¯F¯F pin is open, the output voltage is on
BR200/201
VOUT
(B) VS+
GND
COUT
Figure 4. VS+ peripheral circuit
• When the ON/¯O¯¯F¯F pin is connected to GND, the output voltage
is off
The ON/¯O¯¯F¯F pin is also used as a soft-start function. Do not con-
nect the ON/¯O¯¯F¯F pin to the other pins in parallel, and be sure to
connect the ON/¯O¯¯F¯F pin to a single switch device such as a FET
(see figure 5). Do not pull-up the ON/¯O¯¯F¯F pin from the external
voltage source.
BR200/201
ON/OFF
GND
CAUTION:
• The ON/¯O¯¯F¯F pin is pulled-up inside the BR200/201 converter.
Therefore, a voltage of 6.5 V is output to the ON/¯O¯¯F¯F pin.
Figure 5. ON/¯O¯¯F¯¯F¯ peripheral circuit
• Do not feed voltage to the ON/¯O¯¯F¯F pin from outside BR200/201
converter.
Load
Load
BR200-DS, Rev. 0.2
SANKEN ELECTRIC CO., LTD.
6
Free Datasheet http://www.Datasheet4U.com

6 Page



ページ 合計 : 12 ページ
 
PDF
ダウンロード
[ BR200 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
BR200

(BR200 / BR201) POL Converter Module

Sanken
Sanken
BR201

(BR200 / BR201) POL Converter Module

Sanken
Sanken
BR2016

Lithium Coin Batteries

Panasonic
Panasonic
BR202

(BR202 / BR203) POL Converter Module

Sanken
Sanken


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap