|
|
MX29F800CBのメーカーはMACRONIXです、この部品の機能は「8M-BIT [1024K x 8 / 512K x 16] SINGLE VOLTAGE 5V ONLY FLASH MEMORY」です。 |
部品番号 | MX29F800CB |
| |
部品説明 | 8M-BIT [1024K x 8 / 512K x 16] SINGLE VOLTAGE 5V ONLY FLASH MEMORY | ||
メーカ | MACRONIX | ||
ロゴ | |||
このページの下部にプレビューとMX29F800CBダウンロード(pdfファイル)リンクがあります。 Total 30 pages
MX29F800C T/B
FEATURES
8M-BIT [1024K x 8 / 512K x 16] SINGLE VOLTAGE
5V ONLY FLASH MEMORY
GENERAL FEATURES
• Single Power Supply Operation
- 4.5 to 5.5 volt for read, erase, and program operations
• 1,048,576 x 8 / 524,288 x 16 switchable
• Boot Sector Architecture
- T = Top Boot Sector
- B = Bottom Boot Sector
• Sector Structure
- 16K-Byte x 1, 8K-Byte x 2, 32K-Byte x 1, and 64K-Byte x 15
• Sector protection
- Hardware method to disable any combination of sectors from program or erase operations
- Temporary sector unprotected allows code changes in previously locked sectors
• Latch-up protected to 100mA from -1V to Vcc + 1V
• Compatible with JEDEC standard
- Pinout and software compatible to single power supply Flash
PERFORMANCE
• High Performance
- Access time: 70ns
- Byte/Word program time: 9us/11us (typical)
- Erase time: 0.7s/sector, 8s/chip (typical)
• Low Power Consumption
- Low active read current: 40mA (maximum) at 5MHz
- Low standby current: 1uA (typical)
• Minimum 100,000 erase/program cycle
• 20 years data retention
SOFTWARE FEATURES
• Erase Suspend/ Erase Resume
- Suspends sector erase operation to read data from or program data to another sector which is not being
erased
• Status Reply
- Data# Polling & Toggle bits provide detection of program and erase operation completion
HARDWARE FEATURES
• Ready/Busy# (RY/BY#) Output
- Provides a hardware method of detecting program and erase operation completion
• Hardware Reset (RESET#) Input
- Provides a hardware method to reset the internal state machine to read mode
PACKAGE
• 44-Pin SOP
• 48-Pin TSOP
• 48-Ball LFBGA (6x8mm)
• All devices are RoHS Compliant
• All non RoHS Compliant devices are not recommeded for new design in
P/N:PM1493
REV. 1.2, JUL. 05, 2012
1
http://www.Datasheet4U.com
1 Page 48-Ball LFBGA (6x8mm)
MX29F800C T/B
6
A13 A12
A14 A15
A16 BYTE#
Q15/
A-1
GND
5 A9 A8 A10 A11 Q7 Q14 Q13 Q6
4
WE#
RE-
SET#
NC
NC
Q5
Q12 VCC Q4
3
RY/
BY#
NC
A18 NC
Q2
Q10 Q11 Q3
2 A7 A17 A6 A5 Q0 Q8 Q9 Q1
1
A3
A4 A2
A1 A0
CE#
OE#
GND
A B C DE F G H
PIN DESCRIPTION
LOGIC SYMBOL
SYMBOL
PIN NAME
A0~A18 Address Input
Q0~Q14 Data Input/Output
Q15/A-1 Q15(Word mode)/LSB addr(Byte mode)
CE# Chip Enable Input
WE# Write Enable Input
BYTE# Word/Byte Selection input
RESET# Hardware Reset Pin/Sector Protect
Unlock
OE# Output Enable Input
RY/BY# Ready/Busy Output
VCC Power Supply Pin (+5V)
GND Ground Pin
19
A0-A18
CE#
OE#
WE#
RESET#
BYTE#
Q0-Q15
(A-1)
16 or 8
RY/BY#
P/N:PM1493
REV. 1.2, JUL. 05, 2012
3
http://www.Datasheet4U.com
3Pages MX29F800C T/B
Table 2. BUS OPERATION
Mode
Pins CE# OE# WE# RESET# A0 A1 A6 A9
Q0 ~ Q15
Read Silicon ID
L LH
Manufacture Code
Read Silicon ID
L LH
Device Code
Read
L LH
Standby
HXX
Output Disable
LHH
Write
LHL
Sector Protect
LHL
Chip Unprotect
LHL
Verify Sector Protect/Unprotect L L H
Reset
XXX
Notes:
1. Vhv is the very high voltage, 11.5V to 12.5V.
2. X means input high (Vih) or input low (Vil).
3. SA means sector address: A12~A18.
4. Code=00H/XX00H means unprotected.
Code=01H/XX01H means protected.
H
L L X Vhv
C2H (Byte mode)
00C2H (Word mode)
H H L X Vhv D6/58 (Byte mode)
22D6/2258(Word mode)
H A0 A1 A6 A9
H XXXX
DOUT
HIGH Z
H XXXX
HIGH Z
H A0 A1 A6 A9
Vhv L H L X
Vhv L H H X
H L H L Vhv
DIN
DIN
DIN
Code(4)
L XXXX
HIGH Z
P/N:PM1493
REV. 1.2, JUL. 05, 2012
6
http://www.Datasheet4U.com
6 Page | |||
ページ | 合計 : 30 ページ | ||
|
PDF ダウンロード | [ MX29F800CB データシート.PDF ] |
データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。 |
部品番号 | 部品説明 | メーカ |
MX29F800CB | 8M-BIT [1024K x 8 / 512K x 16] SINGLE VOLTAGE 5V ONLY FLASH MEMORY | MACRONIX |
MX29F800CT | 8M-BIT [1024K x 8 / 512K x 16] SINGLE VOLTAGE 5V ONLY FLASH MEMORY | MACRONIX |