DataSheet.jp

EAP-E-PA の電気的特性と機能

EAP-E-PAのメーカーはTelegesisです、この部品の機能は「Ethernet Access Point Manual」です。


製品の詳細 ( Datasheet PDF )

部品番号 EAP-E-PA
部品説明 Ethernet Access Point Manual
メーカ Telegesis
ロゴ Telegesis ロゴ 




このページの下部にプレビューとEAP-E-PAダウンロード(pdfファイル)リンクがあります。
Total 16 pages

No Preview Available !

EAP-E-PA Datasheet, EAP-E-PA PDF,ピン配置, 機能
Telegesis
EAP-E, EAP-E-PA
TG-EAPE-PM-006-104
Product Manual 1.04
EAP-E and EAP-E-PA Ethernet Access Point
PRODUCT MANUAL
©2009 Telegesis (UK) Ltd
EAP-E Product Manual (Rev 1.04)
Free Datasheet http://www.datasheet-pdf.com/

1 Page





EAP-E-PA pdf, ピン配列
EAP-E
1 Introduction
The EAP-E Ethernet access point allows access to an ETRX2 or ETRX2-PA wireless mesh
networking module via Ethernet using the Lantronix® XPort® DirectTM serial to Ethernet bridge
device. The Telegesis AT-Command interface - based on the EmberZNet meshing stack - can be
easily accessed by the application software using telnet or by creating a virtual COM port using the
supported Lantronix® CPR (COM Port Redirector) software for windows.
By default the EAP-E is set up to use DHCP for easy integration into most networks. Depending on
the network and firewall configuration it is possible to connect to one or more local EAP-Es via the
internet allowing remote interaction with local ZigBee® networks.
Using the Ember bootloader custom firmware and firmware upgrades can be downloaded via
Ethernet or over the air. The SIF interface also allows the EAP-E to be used as a platform for
firmware development and debugging.
The EAP-E access points also support the use of Ember’s EZSP (Ember ZigBee® Serial Protocol)
instead of the Telegesis AT Command interface.
1.1 Installation Requirements
5V-6V Power Supply (supplied separately)
Cat5 Ethernet Cable
10/100 MBit Ethernet connectivity (ideally with DHCP server)
Mains Socket
1.2 LEDs
The EAP-E has two LEDs situated on the RJ45 Ethernet connector:
1. Green Link LED
- off: No link
- on: Link established
2. Yellow Activity Led
- off: No activity
- on: Activity
©2009 Telegesis (UK) Ltd
-3-
EAP-E Product Manual (Rev 1.04)
Free Datasheet http://www.datasheet-pdf.com/


3Pages


EAP-E-PA 電子部品, 半導体
EAP-E
Once the IP address of the EAP-E is known it is possible to open a telnet session connecting to
the built-in ETRX2. By default the port connecting to the ETRX2 is port number 10001 as shown in
Figure 3. Please note that Figure 3 also shows a local command echo, which is why the characters
of the command ATI are repeated.
Figure 2: The Lantronix DeviceInstaller
The default Port number of 10001 can be changed to any port number in order to allow multiple
EAP-Es to be addressed via the internet. To do this the local router/firewall needs to be set up to
forward incoming ports to the respective port of the corresponding local EAP-Es. All you need now
to connect to your ZigBee® network via the internet is the remote IP address and the port number.
©2009 Telegesis (UK) Ltd
-6-
EAP-E Product Manual (Rev 1.04)
Free Datasheet http://www.datasheet-pdf.com/

6 Page



ページ 合計 : 16 ページ
 
PDF
ダウンロード
[ EAP-E-PA データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
EAP-E-PA

Ethernet Access Point Manual

Telegesis
Telegesis


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap