|
|
PDF CS1060 Data sheet ( Hoja de datos )
| Número de pieza | CS1060 | |
| Descripción | 70 Amp AC/DC Current Probe Manual | |
| Fabricantes | Cleverscope | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de CS1060 (archivo pdf) en la parte inferior de esta página. Total 20 Páginas | ||
|
No Preview Available !
70 Amp AC/DC Current Probe
CS 1060 (PA-677)
DC-1MHz
(1mV=2mA at 500 mV/A)
INSTRUCTION MANUAL
Free Datasheet http://www.datasheet-pdf.com/
1 page  
General Safety Instructions:
Read the following safety instructions to avoid injury and prevent damage
to this product or any products connected to it. Use this product only as
specified.
Only qualified personnel should perform service procedures.
To Avoid Fire or Personal Injury
Connect and Disconnect Properly. Connect the probe output to the
measurement instrument before connecting the probe to the circuit under
test. Disconnect the probe input and the probe ground from the circuit
under test before disconnecting the probe from the measurement
instrument.
Observe All Terminal Ratings. To avoid fire or shock hazard, observe
all rating and markings on the product. Consult the instruction manual for
further ratings information before making connections to the product.
Replace Batteries Properly. Replace batteries only with the proper
type and rating specified.
Do Not Operate Without Covers. Do not operate this product without
the covers or panels.
Avoid Exposed Circuitry. Do not touch exposed connections and
components when power is present.
Do Not Operate With Suspected Failures. If you suspect there is
damage to this product, have it inspected by qualified service personnel.
Do Not Operate in Wet/Damp Conditions.
Do Not Operate in an Explosive Atmosphere.
Keep Product Surfaces Clean and Dry.
4
Free Datasheet http://www.datasheet-pdf.com/
5 Page 
ʳ
Figure 4: Increasing the sensitivity
Maintenance:
Use the information in this section to properly maintain the operation of
your PA-677 AC/DC Current Probe.
1. Notes on Battery and Power Converter:
The PA-677 current probe uses a single square 9 V battery. This machine
is a high power product. Please use the specified alkaline battery.
As the battery in the PA-677 current probe is drained, significant gain
errors may occur. The green LED will continue to light until a low battery
voltage of 6.5 V is reached.
If probe gain errors are detected, replace the battery with a fresh one.
As an alternative, an AC power converter can be used to avoid gain error
due to poor battery durability. Switch to a square 9V battery only when
there is no AC power supply available outdoors.
When using an AC power converter for an extended time, we suggest you
remove the battery from the compartment. This is because heating will
result in battery leakage, and battery electrolyte will rust the circuit board,
thus creating major damage. Furthermore, batteries are high pollution
products and therefore by reducing their usage, we will in turn protect the
environment.
10
Free Datasheet http://www.datasheet-pdf.com/
11 Page | ||
| Páginas | Total 20 Páginas | |
| PDF Descargar | [ Datasheet CS1060.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| CS1060 | Reaction Torque Sensor |  Measurement |
| CS1060 | Reaction Torque Sensor |  FGP |
| CS1060 | 5.4 - 5.9 GHz 10 dB Directional Coupler |  Clear Microwave |
| CS1060 | 70 Amp AC/DC Current Probe Manual | Cleverscope |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |