DataSheet.jp

HIP5600IS2 の電気的特性と機能

HIP5600IS2のメーカーはHarris Corporationです、この部品の機能は「Thermally Protected High Voltage Linear Regulator」です。


製品の詳細 ( Datasheet PDF )

部品番号 HIP5600IS2
部品説明 Thermally Protected High Voltage Linear Regulator
メーカ Harris Corporation
ロゴ Harris Corporation ロゴ 




このページの下部にプレビューとHIP5600IS2ダウンロード(pdfファイル)リンクがあります。

Total 16 pages

No Preview Available !

HIP5600IS2 Datasheet, HIP5600IS2 PDF,ピン配置, 機能
Semiconductor
PPRNAOORCTNEWSESWITOHDBDESRSOAIGWLNENSTE
HIP5600
September 1998 File Number 3270.7
[ /Title
()
/Sub-
ject ()
/Autho
r ()
/Key-
words
()
/Cre-
ator ()
/DOCI
NFO
pdf-
mark
[
/Page-
Mode
/Use-
Out-
lines
/DOC-
VIEW
pdf-
mark
Thermally Protected High Voltage Linear
Regulator
The HIP5600 is an adjustable 3-terminal positive linear
voltage regulator capable of operating up to either 400VDC
or 280VRMS. The output voltage is adjustable from 1.2VDC
to within 50V of the peak input voltage with two external
resistors. This high voltage linear regulator is capable of
sourcing 1mA to 30mA with proper heat sinking. The
HIP5600 can also provide 40mA peak (typical) for short
periods of time.
Protection is provided by the on chip thermal shutdown and
output current limiting circuitry. The HIP5600 has a unique
advantage over other high voltage linear regulators due to its
ability to withstand input to output voltages as high as
400V(peak), a condition that could exist under output short
circuit conditions.
Common linear regulator configurations can be implemented
as well as AC/DC conversion and start-up circuits for switch
mode power supplies.
The HIP5600 requires a minimum output capacitor of 10µF
for stability of the output and may require a 0.02µF input
decoupling capacitor depending on the source impedance. It
also requires a minimum load current of 1mA to maintain
output voltage regulation.
All protection circuitry remains fully functional even if the
adjustment terminal is disconnected. However, if this
happens the output voltage will approach the input voltage.
Pinouts
HIP5600 (TO-220)
TOP VIEW
TAB ELECTRICALLY
CONNECTED
TO VOUT
VOUT
Features
• Operates from 50VDC to 400VDC
• Operates from 50VRMS to 280VRMS Line
• UL Recognized
• Variable DC Output Voltage 1.2VDC to VIN - 50V
• Internal Thermal Shutdown Protection
• Internal Over Current Protection
• Up to 40mA Peak Output Current
• Surge Rated to ±650V; Meets IEEE/ANSI C62.41.1980
with Additional MOV
CAUTION: This product does not provide isolation from AC
line.
Applications
• Switch Mode Power Supply Start-Up
• Electronically Commutated Motor Housekeeping Supply
• Power Supply for Simple Industrial/Commercial/Consumer
Equipment Controls
• Off-Line (Buck) Switch Mode Power Supply
Ordering Information
PART
NUMBER
HIP5600IS
HIP5600IS2
TEMP. RANGE
-40oC to +100oC
-40oC to +100oC
PACKAGE
3 Lead Plastic SIP
3 Lead Gullwing Plastic
SIP
HIP5600 (MO-169)
TOP VIEW
HIP5600
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
Copyright © Harris Corporation 1998

1 Page





HIP5600IS2 pdf, ピン配列
HIP5600
Absolute Maximum Ratings
Thermal Information (Typical)
Input to Output Voltage, Continuous. . . . . . . . . . . . . +480V to -550V
Input to Output Voltage, Peak (Non Repetitive, 2ms) . . . . . . . . ±650V
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150oC
ADJ to Output, Voltage to ADJ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±5V
Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC
Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +265oC
Thermal Resistance
Plastic SIP Package . . . . . . . . . . . . . .
60θoJCA/W
4oθCJC/W
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Operating Conditions
Operating Voltage Range . . . . . . . . . . . . . . 80VRMS to 280VRMS or
50VDC to 400VDC
Operating Temperature Range . . . . . . . . . . . . . . . .-40oC to +100oC
Electrical Specifications Conditions VIN = 400VDC, IL = 1mA, CL = 10µF, VADJ = 3.79V, VOUT = 5V (Unless Otherwise Specified) Tem-
perature = Case Temperature.
PARAMETER
CONDITION
TEMP
MIN TYP MAX UNITS
INPUT
Input Voltage
DC Full 50 - 400 V
Max Peak Input Voltage
Non-Repetitive (2ms)
Full
-
- ±650
V
Input Frequency (Note 1)
Full
DC
- 1000
Hz
Bias Current (IBIAS Note 2)
REFERENCE
IADJ
IADJTC (Note 1)
IADJ LOAD REG (Note 1)
VREF (Note 3)
VREF TC (Note 1)
Line Regulation
VREF LINE REG
Load Regulation
VREF LOAD REG
Full 0.4 0.5 0.6 mA
IL = 1mA
IL = 1mA to 10mA
IL = 1mA
50VDC to 400VDC
IOUT = 1mA to 10mA
+25oC
Full
+25oC
+25oC
Full
+25oC
Full
+25oC
Full
50 65 80
- +0.15 -
- -215 -
1.07 1.18 1.30
- -460 -
- 9 14.5
- 9 29
- 35
- 36
µA
µA/oC
nA/mA
V
µV/oC
µV/V
µV/V
mV/mA
mV/mA
PROTECTION CIRCUITS
Output Short Circuit Current Limit
Thermal Shutdown TTS
(IC surface, not case temperature. Note 1)
VIN = 50V
VIN = 400V
Thermal Shutdown Hysteresis (Note 1)
VIN = 400V
NOTES:
1. Characterized not tested
2. Bias current input current with output pin floating.
3. VREF = VOUT - VADJ
+25oC
35
-
45
- 127 134 142
- - 34 -
mA
oC
oC
3


3Pages


HIP5600IS2 電子部品, 半導体
HIP5600
A thermal network that describes the heat flow from the inte-
grated circuit to the ambient air is shown in Figure 6. The
basic relation for thermal resistance from the IC surface, his-
torically called “junction”, to ambient (θJA) is given in Equa-
tion 5. The thermal resistance of the heat sink (θSA) to
maintain a desired junction temperature is calculated using
Equation 6.
TJ = JUNCTION
TC = CASE
TS = HEAT SINK
TA = AMBIENT AIR
PD
θJC
θCS
θSA HEAT SINK
FIGURE 6.
θJA = T-----J-----P–----T-----A--
° C
--W------
Where:
θJA = θJC + θCS + θSA
and
(EQ. 5)
TJ = TTS
θSA + θCS θSA = T-----T----S---P---–-----T----A--- – θJC
(EQ. 6)
Where:
θJA = (Junction to Ambient Thermal Resistance) The sum of
the thermal resistances of the heat flow path.
θJA = θJC + θCS + θSA
TJ = (Junction Temperature) The desired maximum junc-
tion temperature of the part. TJ = TTS
TTS = (Thermal Shutdown Temperature) The maximum
junction temperature that is set by the thermal pro-
tection circuitry of the HIP5600
(min = +127oC, typ = +134oC and max = +142oC).
θJC = (Junction to Case Thermal Resistance) Describes the
thermal resistance from the IC surface to its case.
θJC = 4.8oC/W
θCS = (Case to Mounting Surface Thermal Resistance) The
resistance of the mounting interface between the
transistor case and the heat sink.
For example, mica washer.
θSA = (Mounting Surface to Ambient Thermal Resistance)
The resistance of the heat sink to the ambient air.
Varies with air flow.
TA = Ambient Temperature
P = The power dissipated by the HIP5600 in watts.
P = (VIN - VOUT)(IOUT)
W+1o2r7sot CcainseEqθuSaAtioisn
calculated
6.
using
the
minimum
TTS
of
Example,
Given: VIN = 400VDC
θJC = 4.8oC/W
TA = +50oC
VREF = 1.18V
VOUT = 15V
TTS = +127οC
RF1 = 1.1k
ILOAD = 15mA
IADJ = 80µA
P = 6.2W = (VIN - VOUT)(IIN)
IIN IADJ + V---R--R----F--E--1--F--- + ILOAD
Find: Proper heat sink to keep the junction temperature
of the HIP5600 from exceeding TTS (+127oC).
Solution:
Use Equation 6,
θSA = T-----T----S---P---–-----T----A--- – θJC
(EQ. 7)
θSA
=
127°C 50°C
------------------6----.-2--------------------
4.8°
C
=
°C
7.62 --W------
(EQ. 8)
The selection of a heat sink with θSA less than +7.62oC/W
would ensure that the junction temperature would not
exceed the thermal shut down temperature (TTS) of +127oC.
A Thermalloy P/N7023 at 6.2W power dissipation would
meet this requirement with a θSA of +5.7oC/W.
Operation Without A Heatsink
Tpohweepr adcisksaigpeatihoansata+85θoJAC
of
in
+60oC/W. This
still air. Mounting
allows 0.7W
the HIP5600
to a printed circuit board (see Figure 39 through Figure 41)
decreases the thermal impedance sufficiently to allow about
1.6W of power dissipation at +85oC in still air.
Thermal Transient Operation
For applications such as start-up, the HIP5600 in the TO-220
package can operate at several watts -without a heat sink-
for a period of time before going into thermal shutdown.
TJ = JUNCTION
DIE/PACKAGE INTERFACE
TS = HEAT SINK
OR CASE
TA = AMBIENT AIR
PD = IIN (VIN - VOUT)
0.6θJC
0.4θJC
CD
0.5CP
θSA
CS + 0.5CP
FIGURE 7. THERMAL CAPACITANCE MODEL OF HIP5600
Figure 7 shows the thermal capacitances of the TO-220
package, the integrated circuit and the heat sink, if used.
When power is initially applied, the mass of the package
absorbs heat which limits the rate of temperature rise of the
6

6 Page



ページ 合計 : 16 ページ
 
PDF
ダウンロード
[ HIP5600IS2 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
HIP5600IS

Thermally Protected High Voltage Linear Regulator

Harris Corporation
Harris Corporation
HIP5600IS2

Thermally Protected High Voltage Linear Regulator

Harris Corporation
Harris Corporation


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap