DataSheet.jp

HIP5010 の電気的特性と機能

HIP5010のメーカーはIntersil Corporationです、この部品の機能は「7V/ 17A SynchroFET Complementary Drive Synchronous Half-Bridge」です。


製品の詳細 ( Datasheet PDF )

部品番号 HIP5010
部品説明 7V/ 17A SynchroFET Complementary Drive Synchronous Half-Bridge
メーカ Intersil Corporation
ロゴ Intersil Corporation ロゴ 




このページの下部にプレビューとHIP5010ダウンロード(pdfファイル)リンクがあります。

Total 6 pages

No Preview Available !

HIP5010 Datasheet, HIP5010 PDF,ピン配置, 機能
Data Sheet
HIP5010, HIP5011
March 1996 File Number 4029.5
7V, 17A SynchroFET™ Complementary
Drive Synchronous Half-Bridge
Designed with the P6 and Pentium® in mind, the Intersil
SynchroFET™ family provides a new approach for
implementing a synchronous rectified buck switching regulator.
The SynchroFET replaces two power DMOSs, a Schottky
diode, two gate drivers and synchronous control circuitry. The
complementary drive circuit turns the upper FET on and the
lower FET off when the input from the PWM is high. When the
input from the PWM goes low the upper FET turns off and the
lower FET turns on. The HIP5011 has a PWM pin that inverts
the relationship from the input to PHASE. This architecture
allows the designer to utilize a low cost single-ended PWM
controller in either a current or voltage mode configuration. The
SynchroFET operates in continuous conduction mode reducing
EMI constraints and enabling high bandwidth operation.
Several features ensure easy start-up. First, the supply currents
stay below specification as the supply voltages ramp up; no
unexpected surges occur that might perturb a soft-start or
deplete a charge-pump. Second, any power-up sequence of
the VCC, VIN, or PWM pins can be used without causing large
currents. Third, the chip operates when VCC is greater than 2V
so VCC can be created from a charge pump powered from VIN.
Pinouts
HIP5010IS1, HIP5011IS1 (SIP - VERTICAL)
TOP VIEW
GND (TAB)
7 PHASE
6 VIN
5 PWM (HIP5010), PWM (HIP5011)
4
3 VCC
2 VIN
1 PHASE
FRONT ROWS = PINS 1, 3, 5, 7
BACK ROWS = PINS 2, 4, 6
GND
(TAB)
HIP5010IS, HIP5011IS (SIP - GULLWING)
TOP VIEW
7 PHASE
6 VIN
5 PWM (HIP5010), PWM (HIP5011)
4
3 VCC
2 VIN
1 PHASE
Features
• Complementary Drive, Half-Bridge Power NMOS
• Use With Low-Cost Single-Output PWM Controllers
• Improve Efficiency Over Conventional Buck Converter with
Schottky Clamp
• Minimum Deadtime Provided by Adaptive Shoot-Through
Protection Eliminates External Schottky
• Grounded Case for Low EMI and Simple Heatsinking
• Low Operating Current
• Frequency Exceeding 1MHz
• Dual Polarity Input Options
• All Pins Surge Protected
Applications
• 5V to 3.3V Synchronous Buck Converters
• Pentium and P6 Power Supplies
• PowerPCPower Supplies
• Bus Terminations (BTL and GTL)
• Drive 5V Motors Directly from Microprocessor
Ordering Information
PART
TEMP.
NUMBER RANGE (oC)
PACKAGE
PKG.
NO.
HIP5010IS
HIP5010IS1
HIP5011IS
-40 to 85
-40 to 85
-40 to 85
7 Ld Gullwing SIP
Z7.05B
7 Ld Staggered Vertical SIP Z7.05C
7 Ld Gullwing SIP
Z7.05B
HIP5011IS1 -40 to 85 7 Ld Staggered Vertical SIP Z7.05C
Typical Application Block Diagram
+12V
+5V
VCC
VIN
PWM
CONTROLLER
PWM
CONTROL
PHASE
+3.3V
HIP5010
GND
SYNCHRONOUS RECTIFIED BUCK CONVERTER
Pentium® is a registered trademark of Intel Corporation.
PowerPC™ is a trademark of International Business Machines.
SynchroFET™ is a trademark of Intersil Corporation.
2-3 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999

1 Page





HIP5010 pdf, ピン配列
HIP5010, HIP5011
Absolute Maximum Ratings
Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +16V
Input Voltage
IPHASE, IVIN,
VIN . . . . . .
IGND (TJ =
.....
25oC)
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
....
17A
.........
(Repetitive
. +7V
Peak)
IPHASE, IVIN, IGND (TJ = 150oC) . . . . . . . . . . 15A (Repetitive Peak)
PWM Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -4V to +16V
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 3 (4kV)
Lead Temperature (Soldering 10s) (Lead Tips Only). . . . . . . 300oC
Storage Temperature Range . . . . . . . . . . . . . . . . . . -65oC to 150oC
Junction Temperature Range . . . . . . . . . . . . . . . . . . -40oC to 150oC
Operating Conditions
Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . +12V, 20%
Input Voltage VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to 5.5V
Supply Voltage, VCC, minimum for charge-pumped start-up . +4.0V
Thermal Information (Typical)
Package
θJC ††
(oC/W)
0
θJA (oC/W)
123
3†††
SOIC (IB) . . . 26 63 45 42 41 35
SIP (IS). . . . . 2
55 30 25 24 18
SIP (IS1). . . . 2 - - - - -
Versus additional square inches of 1 ounce copper on the
printed circuit board.
†† θJC is measured to pin 12 for the SOIC. Printed circuit board
had 1 square inch of copper. For SIP Packages value shown is
typical with an infinite heat sink.
††† 200 linear feet per minute of air flow.
IPHASE.SIPs:11.5A(RMS), 11.2A(DC); SOIC:7.4A(RMS), 7.4A(DC)
IVIN . . . SIPs:10.0A(RMS), 8.5A(DC); SOIC:6.4A(RMS), 6.4A(DC)
IGND. . . . .SIPs:8.5A(RMS), 6.0A(DC); SOIC:5.4A(RMS), 5.4A(DC)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the recommended operating conditions of this specification is not implied.
Electrical Specifications
PARAMETERS
rDS(ON) Upper MOSFET
rDS(ON) Lower MOSFET
VIN Operating Current
VIN Quiescent Current
VCC Operating Current
VCC Quiescent Current (HIP5010)
VCC Quiescent Current (HIP5010)
VCC Quiescent Current (HIP5011)
VCC Quiescent Current (HIP5011)
Low Level PWM Input Voltage
High Level PWM Input Voltage
PWM Input Voltage Hysteresis
Input Pulldown Resistance (HIP5010)
Input Pullup Resistance (HIP5011)
SYMBOL
TEST CONDITIONS
RDSU
RDSL
IVINO
IVIN
ICCO
ICCIH
ICCIL
ICCNIH
ICCNIL
VIL
VIH
VIHYS
RPWM
RPWM
VCC = 12V, VIN = 5V
VCC = 12V, VIN = 5V
VIN = 5V, No Load, 500kHz
PWM or PWM = VCC or GND
VCC = 12V, 500kHz
PWM = VCC
PWM = GND
PWM = VCC
PWM = GND
Switching Specifications
PARAMETERS
Upper Device Turn-Off Delay
Lower Device Turn-Off Delay
Dead Time
Phase Rise-Time
Phase Fall-Time
SYMBOL
TEST CONDITIONS
tPHL
tPLH
tDT
tr
tf
VCC = 12V, IPHASE = -1A
VCC = 12V, IPHASE = +1A
VCC = +12V, IPHASE = -1A
VCC = 12V, IPHASE = -1A
VCC = 12V, IPHASE = +1A
TJ = 25oC
MIN TYP MAX
- 34 39
- 36 42
- 58
- 0.1 10
- 8 12
- 80 -
- 0.1 10
- 0.1 10
- 140 -
- 1.8 -
- 2.1 -
- 0.3 -
- 220 -
- 220 -
TJ
TJ
=
=
- 40oC
150oC
MIN MAX UNITS
- 65 m
- 68 m
- 10 mA
- 100 µA
- 15 mA
- 400 µA
- 100 µA
- 100 µA
- 400 µA
1- V
-3V
--V
100 400 k
100 400 k
TJ = 25oC
MIN TYP MAX
- 30 50
- 30 50
- 10 -
- 20 -
- 20 -
TJ
TJ
=
=
- 40oC
150oC
MIN MAX UNITS
- 80 ns
- 80 ns
- - ns
- - ns
- - ns
2-5


3Pages


HIP5010 電子部品, 半導体
HIP5010, HIP5011
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time with-
out notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
Sales Office Headquarters
NORTH AMERICA
Intersil Corporation
P. O. Box 883, Mail Stop 53-204
Melbourne, FL 32902
TEL: (407) 724-7000
FAX: (407) 724-7240
EUROPE
Intersil SA
Mercure Center
100, Rue de la Fusee
1130 Brussels, Belgium
TEL: (32) 2.724.2111
FAX: (32) 2.724.22.05
ASIA
Intersil (Taiwan) Ltd.
7F-6, No. 101 Fu Hsing North Road
Taipei, Taiwan
Republic of China
TEL: (886) 2 2716 9310
FAX: (886) 2 2715 3029
2-8

6 Page



ページ 合計 : 6 ページ
 
PDF
ダウンロード
[ HIP5010 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
HIP5010

7V/ 17A SynchroFET Complementary Drive Synchronous Half-Bridge

Intersil Corporation
Intersil Corporation
HIP5010IS

7V/ 17A SynchroFET Complementary Drive Synchronous Half-Bridge

Intersil Corporation
Intersil Corporation
HIP5010IS1

7V/ 17A SynchroFET Complementary Drive Synchronous Half-Bridge

Intersil Corporation
Intersil Corporation
HIP5011

7V/ 17A SynchroFET Complementary Drive Synchronous Half-Bridge

Intersil Corporation
Intersil Corporation


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap