|
|
PDF HIP1030AS Data sheet ( Hoja de datos )
| Número de pieza | HIP1030AS | |
| Descripción | 1A High Side Driver with Overload Protection | |
| Fabricantes | Intersil Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de HIP1030AS (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
|
No Preview Available !
HIP1030
December 1997
1A High Side Driver with
Overload Protection
Features
• Over Operating Temperature Range . . -40oC to 125oC
- Max VSAT at 1A . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1V
- Current Switching Capability . . . . . . . . . . . . . . . . .1A
- Power Supply Range . . . . . . . . . . . . . . . . 4.5V to 25V
• Over-Voltage Shutdown Protected
• Over-Current Limiting
• Thermal Limiting Protection
• Negative Output Voltage Clamp
• CMOS/TTL Logic Level Control Input
• Load Dump . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60VPEAK
• Reverse Battery Protection to -16V
Applications
• Motor Driver/Controller
• Driver for Solenoids, Relays and Lamps
• MOSFET and IGBT Driver
• Driver for Temperature Controller
Ordering Information
TEMP.
PART NUMBER RANGE (oC)
PACKAGE
PKG.
NO.
Description
The HIP1030 is a High Side Driver Power Integrated Circuit
designed to switch power supply voltage to an output load. It
is the equivalent of a PNP pass transistor operated as a
protected high side current switch in the saturated ON state
with low forward voltage drop at the maximum rated current.
The HIP1030 has low output leakage and low idle current in
the OFF state.
The Functional Block Diagram for the HIP1030 shows the
protection control circuit functions of over-current, overvoltage
and over-temperature. A small metal resistor senses over-
current in the power supply path of the pass transistor and load.
Overvoltage detection and shutdown of the output driver occurs
when a comparator determines that the supply voltage has
exceeded a comparator reference level. Over-temperature is
sensed from a VBE differential sense element that is thermally
close to the output drive transistor. In addition to the input
detected overvoltage protection, negative peak voltage of a
switched inductive load is clamped with an internal zener diode.
An internal bandgap voltage source provides a stable voltage
reference over the operating temperature range, providing bias
and reference control for the protection circuits.
The HIP1030 is particularly well suited for driving lamps,
relays, and solenoids in automotive and industrial control
applications where voltage and current overload protection
at high temperatures is required. The HIP1030 is supplied in
a 5 lead TS-001AA Power SIP package.
HIP1030AS
-40 to 125 5 Ld TS-001AA SIP Z5.067C
Pinout
Functional Block Diagram
HIP1030 (SIP)
TOP VIEW
5 VIN (CONTROL)
4 GND
3 TAB GND
2 VOUT (LOAD)
1 VCC (SUPPLY)
VCC
1
VBATT
SUPPLY
OVER-
VOLTAGE
SHUTDOWN
RS
CURRENT
LIMIT
THERMAL
LIMIT
CONTROL
CIRCUIT
VOUT
2
NEG.
CLAMP
ZENER
VIN
5
CONTROL
TAB
3
GND
HIP1030
4
GND
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
1
File Number 2788.7
1 page  
HIP1030
Single-In-Line Plastic Packages (SIP)
ØP
H1
E
A
A1
Q
D
L1
L
b1
c
60o
b
1234 5
e
e1
J1
Z5.067C (ALTERNATE VERSION)
5 LEAD PLASTIC SINGLE-IN-LINE PACKAGE
INCHES
MILLIMETERS
SYMBOL MIN MAX MIN MAX NOTES
A
0.170
0.180
4.32
4.57
-
A1
0.048
0.052
1.22
1.32
3, 4
b
0.030
0.034
0.77
0.86
3, 4
b1
0.031
0.041
0.79
1.04
3, 4
c
0.018
0.022
0.46
0.55
3, 4
D
0.590
0.610 14.99
15.49
-
E
0.395
0.405 10.04
10.28
-
e 0.067 TYP
1.70 TYP
5
e1 0.268 BSC
6.80 BSC
H1
0.235
0.255
5.97
6.47
J1
0.095
0.105
2.42
2.66
L
0.530
0.550 13.47
13.97
5
-
6
-
L1
0.110
0.130
2.80
3.30
ØP
0.149
0.153
3.79
3.88
2
-
Q
0.105
0.115
2.66
2.92
-
NOTES:
Rev. 1 4/96
1. These dimensions are within allowable dimensions of Rev. A of
JEDEC TS-001AA outline dated 8-89.
2. Solder finish uncontrolled in this area.
3. Lead dimension (without solder).
4. Add typically 0.002 inches (0.05mm) for solder plating.
5. Position of lead to be measured 0.250 inches (6.35mm) from
bottom of dimension D.
6. Position of lead to be measured 0.100 inches (2.54mm) from
bottom of dimension D.
7. Controlling dimension: Inch.
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate
and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which
may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
5
5 Page | ||
| Páginas | Total 5 Páginas | |
| PDF Descargar | [ Datasheet HIP1030AS.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| HIP1030AS | 1A High Side Driver with Overload Protection | Intersil Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |