|
|
PDF HIP1013 Data sheet ( Hoja de datos )
| Número de pieza | HIP1013 | |
| Descripción | Low Cost Dual Power Distribution Controller | |
| Fabricantes | Intersil Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de HIP1013 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
®
Data Sheet
August 2004
HIP1013
FN4516.3
Low Cost Dual Power Distribution
Controller
The HIP1013 is a low cost HOT SWAP dual supply power
distribution controller. Two external N-Channel MOSFETs are
driven to distribute power while providing load fault isolation. At
turn-on, the gate of each external N-Channel MOSFET is
charged with a 10µA current source. Capacitors on each gate
(see the Typical Application Diagram), create a programmable
ramp (soft turn-on) to control inrush currents. A built in charge
pump supplies the gate drive for the 12V supply N-Channel
MOSFET switch.
Over current protection is facilitated by two external current
sense resistors. When the current through either resistor
exceeds the user programmed value the N-Channel MOSFETs
are latched off by the HIP1013. The controller is reset by a
rising edge on either PWRON pin.
Choosing the voltage selection mode the HIP1013 controls
either +12V/5V or +3.3V/+5V supplies.
Although pin compatible with the HIP1012 device, the HIP1013
does not offer current regulation during an OC event.
Ordering Information
PART
NUMBER
TEMP.
RANGE (°C)
PACKAGE
PKG.
DWG. #
HIP1013CB
-0 to 70
14 Ld SOIC
M14.15
HIP1013CBZA (Note)
-0 to 70
14 Ld SOIC
(Pb-free)
M14.15
NOTE: Intersil Pb-free products employ special Pb-free material
sets; molding compounds/die attach materials and 100% matte tin
plate termination finish, which is compatible with both SnPb and
Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed
the Pb-free requirements of IPC/JEDEC J Std-020B.
*Tape & Reel packaging available with “-T” suffix..
Pinout
HIP1013 (SOIC)
TOP VIEW
3/12VS 1
3/12VG 2
VDD 3
MODE/ 4
PWRON1
PWRON2 5
5VG 6
5VS 7
14 3/12VISEN
13 RILIM
12 GND
11 CPUMP
10 NC
9 PGOOD
8 5VISEN
Features
• HOT SWAP Dual Power Distribution Control for +5V and
+12V or +5V and +3.3V
• Provides Fault Isolation
• Charge Pump Allows the Use of N-Channel MOSFETs
• Redundant Power On Controls
• Power Good and Over Current Latch Indicators
• Adjustable Turn-On Ramp
• Protection During Turn-On
• Pb-free Available
Applications
• Power Distribution Control
• Hot Plug™ Components
Typical Application Diagram
CPUMP
12V
VDD
CGATE
POWER ON
INPUTS
5V
CGATE
RSENSE
HIP1013
3/12VISEN
3/12VS
3/12VG
VDD
M/PON1
RILIM
GND
CPUMP
PWRON2
NC
5VG
PGOOD
5VS 5ISEN
RSENSE
RLOAD
RILIM
5V
RLOAD
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 1998, 1999, 2004. All Rights Reserved
Hot Plug™ is a trademark of Core International, Inc. All other trademarks mentioned are the property of their respective owners.
1 page  
HIP1013
Typical Performance Curves
8.4
8.2
8.0
7.8
7.6
7.4
7.2
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80
TEMPERATURE (°C)
FIGURE 1. SUPPLY CURRENT
105
104
103
102
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80
TEMPERATURE (°C)
FIGURE 2. RILIM SOURCE CURRENT
11.00
4.615
2.888
10.98
10.96
4.610
5V UV
4.605
4.600
3.3V UV
2.886
2.884
2.882
10.94
-40 -20 0
20 40
60
TEMPERATURE (°C)
FIGURE 3. 12V UV THRESHOLD
80
4.595
-40
-20 0 20 40
TEMPERATURE (°C)
2.880
60 80
FIGURE 4. 3.3V/5V UV THRESHOLD
17.36
17.34
17.32
17.30
17.28
17.26
-40
11.935
11.930
12V VG
11.925
11.920
11.915
5V VG
11.910
11.905
-20 0
11.900
20 40 60 80
TEMPERATURE (°C)
FIGURE 5. 12V, 5V GATE DRIVE
5
17.6
17.4
CHARGE PUMP VOLTAGE
NO LOAD
17.2
17.0
CHARGE PUMP VOLTAGE
100µA LOAD
16.8
16.6
-40
-20 0
20 40 60
TEMPERATURE (°C)
FIGURE 6. CHARGE PUMP VOLTAGE
80
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet HIP1013.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| HIP1011 | PCI Hot Plug Controller | Intersil Corporation |
| HIP1011A | PCI Hot Plug Controller | Intersil Corporation |
| HIP1011B | PCI Hot Plug Controller | Intersil Corporation |
| HIP1011D | Dual PCI Hot Plug Controller | Intersil Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |