DataSheet.jp

ISE40-x-30 の電気的特性と機能

ISE40-x-30のメーカーはSMCです、この部品の機能は「Pressure Sensors」です。


製品の詳細 ( Datasheet PDF )

部品番号 ISE40-x-30
部品説明 Pressure Sensors
メーカ SMC
ロゴ SMC ロゴ 




このページの下部にプレビューとISE40-x-30ダウンロード(pdfファイル)リンクがあります。
Total 8 pages

No Preview Available !

ISE40-x-30 Datasheet, ISE40-x-30 PDF,ピン配置, 機能
High Precision,
ZSE40/ISE40Digital Pressure Switch Series
How to Order
Set pressure range
Nil –0.100 to 1.000 MPa For positive pressure
For positive pressure ISE40
For vacuum/compound pressure ZSE40
01 22
01 22
Set pressure range
Nil 10.0 to –101.3 kPa For vacuum pressure
F –100.0 to 100.0 kPa For compound pressure
Piping specifications
01: R 1/8 (With M5 female threads) W1: Rc 1/8
T1: NPT 1/8 (With M5 female threads)
R 1/8, NPT 1/8
Reverse pressure
two directions
Rc 1/8
M5 x 0.8 female threads
Rc 1/8
C4: With ø4 One-touch fitting
C6: With ø6 One-touch fitting
Wall mount
M5: M5 x 0.8 (Female threads)
Wall mount
http://www.DataSheet4U.net/
Option
Nil None
Bracket A
A
(ZS-24-A)
Bracket B
B
(ZS-24-B)
Panel mount (ZS-22-A)
E
ZSE„
ISE„
PSE
ZI SE3
PS
ZI SE12
ZSP
ISA2
IS„
ZSM
PF2„
IF„
Data
Panel mount (ZS-24-C)
+ Front protective cover
ø4, ø6
One-touch fitting
M5 x 0.8
F
Option
Input/Output specifications
22 NPN open collector 2 outputs + analog output
30 NPN open collector 2 outputs + auto shift input
62 PNP open collector 2 outputs + analog output
70 PNP open collector 2 outputs + auto shift input
Option
Note
When equipped with auto shift function, the following ranges can be set.
Set pressure range
–100.0 to 100.0 kPa
10.0 to –101.3 kPa
–0.1 to 1.000 MPa
Setting range
–100.0 to 100.0 kPa
–101.3 to 101.3 kPa
–1.000 to 1.000 MPa
When optional parts only are
required, order with the part
numbers inside ( ).
Unit specifications
Nil With unit switching function Note1)
M SI unit only Note 2)
Note 1) This will no longer be sold for use in
Japan after the new Weight and
Measure Act is implemented
(October,1999).
Note 2) Fixed unit
For vacuum/compound pressure: kPa
For positive pressure: MPa
Lead wire length
Nil 0.6 m
L 3m
16-2-17
datasheet pdf - http://www.DataSheet4U.net/

1 Page





ISE40-x-30 pdf, ピン配列
High Precision,
ZSE40/ISE40Digital Pressure Switch Series
Description
3 1/2-digit LED
Displays present pressure.
Displays each mode.
Displays error mode.
LED (Green)
Displays OUT1 output condition
When it is ON, the LED is
illuminated.
UP button
Switching of the mode and set value
kPa
OUT1
OUT2
SET
LED (Red)
Displays OUT2 output condition.
When it is ON, the LED is
illuminated.
DOWN button
Switches the mode and set value.
SET button
Switches to each mode and fixes
the set value.
Calibration Procedures
Setting procedure
Initial setting
Set “Output mode”, “Response
time” and “Auto or Manual
mode”.
Manual
pressure setting
Enter the set value of the
pressure to perform switch
output.
Auto
preset
Automatically sets the pressure
for the adsorption confirmation
or supply pressure
confirmation.
http://www.DataSheet4U.net/
Zero clear
Adjusts the zero point of the
atmospheric pressure.
Manual
pressure setting
Allows fine-tuning of the
data set automatically by
auto preset.
Key lock
mode
Mode is not switched, even if
the button is pressed during
operation.
Normal operation
Measured pressure is
displayed and the switch
operation begins.
ZSE„
ISE„
PSE
ZI SE3
PS
ZI SE12
ZSP
ISA2
IS„
ZSM
PF2„
IF„
Data
16-2-19
datasheet pdf - http://www.DataSheet4U.net/


3Pages


ISE40-x-30 電子部品, 半導体
Series ZSE40/ISE40
Calibration Procedures
Auto Preset (In the case of confirming the supply pressure)
1. Auto preset mode
2. Preparation for auto preset
3. Auto preset of OUT1
SET
Press the “SET” button.
Select the Auto preset mode in
the initial setting mode and
press the “SET” button until
“ ” is displayed.
Prepare the equipment for use
under operating conditions.
When setting OUT1 is not
required, press both the į
button and Ĭ button
simultaneously in this state to
skip to “ ”.
4. Preparation for auto preset
The pressure is read and the
optimal set value is determind
automatically.
5. Auto preset of OUT2
SET
Press the “SET” button.
SET
Press the “SET” button.
SET
Press the “SET” button
to complete the setting.
ON point (C, C1)
OFF
Hysteresis (3 digits)
ON point = C, C1
OFF point = C-3 digits, C1-3 digits
(1 digit is the minimum setting unit.)
Other Functions
Prepare the equipment for use
under operating conditions of
OUT2.
When setting OUT2 is not
required, press both the į
button and Ĭ button
simultaneously in this state to
skip to the measurement mode.
http://www.DataSheet4U.net/
The pressure is read and the
optimal set value is determind
automatically.
Ȝ Key lock mode
Used to avoid a malfunction when buttons on the front part of the switch are pressed.
Initiate key lock
Release key lock
SET
Press the “SET” button
to complete the setting.
SET
Press the “SET” button
to complete the setting.
Press the “SET” button for 4
seconds or longer.
Release it when the display
turns to “ ”.
Display “ ” by pressing į
button or Ĭ button.
Ȝ Peak mode
Allows holding of the maximum pressure
value on display under measurement.
While displayed, pressing the į button for 1
second or longer causes the peak mode to
display and blink.
Pressing the į button once again for 1 second
or longer reinstates it.
Note) Displaying the peak and the bottom
display is not distinguished.
Ȝ Zero clear
Allows an adjust to zero on the display
if the pressure to be measured is
within a range of ±70 digits from the
atmospheric pressure.
Pressing the į + Ĭ buttons simultaneously
with the supply pressure released to the
atmosphere, causes it to reset to zero on the
display and completes the zero clear
operation. The function then returns to the
measurement mode.
Press the “SET” button for 4
seconds or longer.
Release it when the display
turns to “ ”.
Display “ ” by pressing į
button or Ĭ button.
Ȝ Bottom mode
Allows holding of the minimum pressure
value on display under measurement.
While displayed, pressing the Ĭ button for 1
second or longer causes the bottom mode to
display and blink.
Pressing the Ĭ button once again for 1 second
or longer reinstates it.
Note) Displaying the peak and the bottom
display is not distinguished.
16-2-22
datasheet pdf - http://www.DataSheet4U.net/

6 Page



ページ 合計 : 8 ページ
 
PDF
ダウンロード
[ ISE40-x-30 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
ISE40-x-30

Pressure Sensors

SMC
SMC


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap