|
|
IR26-21CのメーカーはEverlightです、この部品の機能は「LED」です。 |
部品番号 | IR26-21C |
| |
部品説明 | LED | ||
メーカ | Everlight | ||
ロゴ | |||
このページの下部にプレビューとIR26-21Cダウンロード(pdfファイル)リンクがあります。 Total 10 pages
Technical Data Sheet
1.6mm round Subminiature Infrared LED
IR26-21C/L110/TR8
Features
․Small double-end package
․Low forward voltage
․Good spectral matching to Si photo detector
․Package in 12mm tape on 7〞diameter reel.
․Pb free
․The product itself will remain within RoHS compliant version.
Descriptions
․IR26-21C/L110/TR8 is an infrared emitting diode in miniature SMD
package which is molded in a water clear plastic with spherical
top view lens. The device is spectrally matched with silicon
photodiode and phototransistor
www.DataSheet.co.kr
Applications
․PCB mounted infrared sensor
․Infrared emitting for miniature light barrier
․Floppy disk drive
․Optoelectronic switch
․Smoke detector
Device Selection Guide
LED Part No.
Chip
Material
IR GaAlAs
Lens Color
Water Clear
Everlight Electronics Co., Ltd.
Device No:DTR-026-163
http:\\www.everlight.com
Prepared date:08-26-2005
Rev 2
Page: 1 of 10
Prepared by:Jaine Tsai
Datasheet pdf - http://www.DataSheet4U.net/
1 Page IR26-21C/L110/TR8
Electro-Optical Characteristics (Ta=25℃)
Parameter
Radiant Intensity
Peak Wavelength
Spectral Bandwidth
Symbol
Ee
λp
Δλ
Condition
IF=20mA
IF=100mA
Pulse Width≦100μs ,Duty≦1%
IF=20mA
IF=20mA
IF=20mA
Forward Voltage
VF
IF=100mA
Pulse Width≦100μs ,Duty≦1%
IF=1A
Reverse Current
View Angle
IR
2θ1/2
VR=5V
IF=20mA
Min.
1.0
--
--
--
--
--
--
--
--
Typ.
3.5
15
940
45
1.2
1.5
2.6
--
20
Max. Units
--
-- mW /sr
-- nm
-- nm
1.5
1.8 V
4.0
10 μA
-- deg
www.DataSheet.co.kr
Everlight Electronics Co., Ltd.
Device No:DTR-026-163
http:\\www.everlight.com
Prepared date:08-26-2005
Rev 2
Page: 3 of 10
Prepared by:Jaine Tsai
Datasheet pdf - http://www.DataSheet4U.net/
3Pages Precautions For Use
IR26-21C/L110/TR8
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
www.DataSheet.co.kr
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
Everlight Electronics Co., Ltd.
Device No:DTR-026-163
http:\\www.everlight.com
Prepared date:08-26-2005
Rev 2
Page: 6 of 10
Prepared by:Jaine Tsai
Datasheet pdf - http://www.DataSheet4U.net/
6 Page | |||
ページ | 合計 : 10 ページ | ||
|
PDF ダウンロード | [ IR26-21C データシート.PDF ] |
データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。 |
部品番号 | 部品説明 | メーカ |
IR26-21C | LED | Everlight |
IR26-21C-L110-TR8 | 1.6mm round Subminiature Infrared LED | Everlight Electronics |