DataSheet.jp

MOC3022 の電気的特性と機能

MOC3022のメーカーはFairchild Semiconductorです、この部品の機能は「(MOC3021 - MOC3023) 6-Pin DIP Random-phase Optoisolators Triac Driver Output」です。


製品の詳細 ( Datasheet PDF )

部品番号 MOC3022
部品説明 (MOC3021 - MOC3023) 6-Pin DIP Random-phase Optoisolators Triac Driver Output
メーカ Fairchild Semiconductor
ロゴ Fairchild Semiconductor ロゴ 




このページの下部にプレビューとMOC3022ダウンロード(pdfファイル)リンクがあります。

Total 7 pages

No Preview Available !

MOC3022 Datasheet, MOC3022 PDF,ピン配置, 機能
www.DataSheet4U.net
GlobalOptoisolator
6-Pin DIP Random-Phase
Optoisolators Triac Driver Output
(400 Volts Peak)
The MOC3020 Series consists of gallium arsenide infrared emitting diodes,
optically coupled to a silicon bilateral switch.
To order devices that are tested and marked per VDE 0884 requirements, the
suffix ”V” must be included at end of part number. VDE 0884 is a test option.
They are designed for applications requiring isolated triac triggering.
Recommended for 115/240 Vac(rms) Applications:
Solenoid/Valve Controls
Lamp Ballasts
Interfacing Microprocessors to 115 Vac Peripherals
Motor Controls
Static ac Power Switch
Solid State Relays
Incandescent Lamp Dimmers
MAXIMUM RATINGS (TA = 25°C unless otherwise noted)
Rating
Symbol
Value
INFRARED EMITTING DIODE
Reverse Voltage
Forward Current — Continuous
Total Power Dissipation @ TA = 25°C
Negligible Power in Triac Driver
Derate above 25°C
VR 3
IF 60
PD 100
1.33
OUTPUT DRIVER
Off–State Output Terminal Voltage
Peak Repetitive Surge Current
(PW = 1 ms, 120 pps)
VDRM
ITSM
400
1
Total Power Dissipation @ TA = 25°C
Derate above 25°C
PD 300
4
TOTAL DEVICE
Isolation Surge Voltage(1)
(Peak ac Voltage, 60 Hz, 1 Second Duration)
VISO
7500
Total Power Dissipation @ TA = 25°C
Derate above 25°C
PD 330
4.4
Junction Temperature Range
Ambient Operating Temperature Range
Storage Temperature Range
TJ – 40 to +100
TA – 40 to +85
Tstg – 40 to +150
Soldering Temperature (10 s)
TL 260
1. Isolation surge voltage, VISO, is an internal device dielectric breakdown rating.
1. For this test, Pins 1 and 2 are common, and Pins 4, 5 and 6 are common.
Unit
Volts
mA
mW
mW/°C
Volts
A
mW
mW/°C
Vac(pk)
mW
mW/°C
°C
°C
°C
°C
MOC3021
MOC3022
MOC3023
61
STANDARD THRU HOLE
SCHEMATIC
16
25
34
1. ANODE
2. CATHODE
3. NC
4. MAIN TERMINAL
5. SUBSTRATE
5. DO NOT CONNECT
6. MAIN TERMINAL
1

1 Page





MOC3022 pdf, ピン配列
www.DataSheet4U.net
1.4
1.3
1.2
1.1
1
0.9
0.8
0.7
0.6
–40 –20 0 20 40 60 80 100
TA, AMBIENT TEMPERATURE (°C)
Figure 3. Trigger Current versus Temperature
MOC3021, MOC3022, MOC3023
25
q20 NORMALIZED TO:
PWin 100 µs
15
10
5
0
12
5 10 20
50 100
PWin, LED TRIGGER WIDTH (µs)
Figure 4. LED Current Required to Trigger
versus LED Pulse Width
12
STATIC dv/dt
10 CIRCUIT IN FIGURE 7
8
6
4
2
0
25 30
40 50 60 70 80
TA, AMBIENT TEMPERATURE (°C)
90
Figure 5. dv/dt versus Temperature
100
100
10
1
– 40 – 30 – 20 –10 0 10 20 30 40 50 60 70 80
TA, AMBIENT TEMPERATURE (°C)
Figure 6. Leakage Current, IDRM
versus Temperature
+400
Vdc
PULSE
INPUT
RTEST
MERCURY
WETTED
RELAY
APPLIED VOLTAGE
WAVEFORM
252 V
0 VOLTS
tRC
R = 10 k
CTEST
D.U.T.
X100
SCOPE
PROBE
1. The mercury wetted relay provides a high speed repeated
pulse to the D.U.T.
2. 100x scope probes are used, to allow high speeds and
voltages.
3. The worst–case condition for static dv/dt is established by
triggering the D.U.T. with a normal LED input current, then
removing the current. The variable RTEST allows the dv/dt to be
gradually increased until the D.U.T. continues to trigger in
response to the applied voltage pulse, even after the LED
current has been removed. The dv/dt is then decreased until
the D.U.T. stops triggering. tRC is measured at this point and
recorded.
Vmax = 400 V
ń + +dv dt
0.63 Vmax
t RC
252
t RC
Figure 7. Static dv/dt Test Circuit


3Pages


MOC3022 電子部品, 半導体
www.DataSheet4U.net
MOC3021, MOC3022, MOC3023
–A–
64
–B–
13
F 4 PL
–T–
SEATING
PLANE
E 6 PL
N
C
L
GK
D 6 PL
0.13 (0.005) M T A M
BM
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
INCHES
MILLIMETERS
DIM MIN MAX MIN MAX
A 0.320 0.350 8.13 8.89
B 0.240 0.260 6.10 6.60
C 0.115 0.200 2.93 5.08
D 0.016 0.020 0.41 0.50
E 0.040 0.070 1.02 1.77
F 0.010 0.014 0.25 0.36
G 0.100 BSC
2.54 BSC
J 0.008 0.012 0.21 0.30
K 0.100 0.150 2.54 3.81
L 0.400 0.425 10.16 10.80
J N 0.015 0.040 0.38 1.02
0.4" LEAD SPACING

6 Page



ページ 合計 : 7 ページ
 
PDF
ダウンロード
[ MOC3022 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
MOC3020

6pin DIP photocoupler

Lite-On Technology
Lite-On Technology
MOC3020

Optocouplers/Optoisolators (Rev. A)

Texas Instruments
Texas Instruments
MOC3020

(MOC3020 - MOC3023) non-zero-crossing triacs

QT Optoelectronics
QT Optoelectronics
MOC3020

(MOC3020X - MOC3023X) OPTICALLY COUPLED BILATERAL SWITCH NON-ZERO CROSSING TRIAC

ISOCOM COMPONENTS
ISOCOM COMPONENTS


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap