DataSheet.jp

MX25L1605A の電気的特性と機能

MX25L1605AのメーカーはMXICです、この部品の機能は「16M-Bit CMOS Serial Falsh」です。


製品の詳細 ( Datasheet PDF )

部品番号 MX25L1605A
部品説明 16M-Bit CMOS Serial Falsh
メーカ MXIC
ロゴ MXIC ロゴ 




このページの下部にプレビューとMX25L1605Aダウンロード(pdfファイル)リンクがあります。

Total 41 pages

No Preview Available !

MX25L1605A Datasheet, MX25L1605A PDF,ピン配置, 機能
ADVANCED INFORMATION
MX25L1605A
FEATURES
GENERAL
• Serial Peripheral Interface (SPI) compatible -- Mode 0
and Mode 3
• 16,777,216 x 1 bit structure
• 512 Equal Sectors with 4K byte each
- Any Sector can be erased individually
• 32 Equal Blocks with 64K byte each
- Any Block can be erased individually
• Single Power Supply Operation
- 2.7 to 3.6 volt for read, erase, and program operations
• Latch-up protected to 100mA from -1V to Vcc +1V
• Low Vcc write inhibit is from 1.5V to 2.5V
PERFORMANCE
• High Performance
- Fast access time: 70MHz serial clock (15pF + 1TTL
Load) and 66MHz serial clock (30pF + 1TTL Load)
- Fast program time: 1.4ms(typ.) and 5ms(max.)/page
(256-byte per page)
- Fast erase time: 90ms(typ.) and 270ms(max.)/sector
(4K-byte per sector) ; 1s(typ.) and 3s(max.)/block (64K-
byte per block)
• Low Power Consumption
- Low active read current: 12mA(max.) at 70MHz,
8mA(max.) at 66MHz and 4mA(max.) at 33MHz
- Low active programming current: 30mA (max.)
- Low active erase current: 15mA (max.)
- Low standby current: 50uA (max.)
- Deep power-down mode 10uA (typical)
• Minimum 100,000 erase/program cycles
16M-BIT [x 1] CMOS SERIAL FLASH
SOFTWARE FEATURES
• Input Data Format
- 1-byte Command code
• Block Lock protection
- The BP0~BP2 status bit defines the size of the area
to be software protected against Program and Erase
instructions.
• Auto Erase and Auto Program Algorithm
- Automatically erases and verifies data at selected
sector
- Automatically programs and verifies data at selected
page by an internal algorithm that automatically times
the program pulse widths (Any page to be programed
should have page in the erased state first)
Status Register Feature
Electronic Identification
- JEDEC 2-byte Device ID
- RES command, 1-byte Device ID
HARDWARE FEATURES
SCLK Input
- Serial clock input
• SI Input
- Serial Data Input
• SO Output
- Serial Data Output
• WP# pin
- Hardware write protection
• HOLD# pin
- pause the chip without diselecting the chip
• PACKAGE
- 16-pin SOP (300mil)
- 8-land SON (8x6mm)
- 8-pin SOP (200mil)
P/N: PM1211
www.DataSheet.in
REV. 0.01, JUL. 29, 2005
1

1 Page





MX25L1605A pdf, ピン配列
BLOCK DIAGRAM
MX25L1605A
Address
Generator
Memory Array
SI
CS#
SCLK
Page Buffer
Data
Register
SRAM
Buffer
Mode
Logic
State
Machine
Y-Decoder
HV
Generator
Sense
Amplifier
Clock Generator
Output
Buffer
SO
P/N: PM1211
www.DataSheet.in
REV. 0.01, JUL. 29, 2005
3


3Pages


MX25L1605A 電子部品, 半導体
MX25L1605A
HOLD FEATURE
HOLD# pin signal goes low to hold any serial communications with the device. The HOLD feature will not stop the operation
of write status register, programming, or erasing in progress.
The operation of HOLD requires Chip Select(CS#) keeping low and starts on falling edge of HOLD# pin signal while Serial
Clock (SCLK) signal is being low (if Serial Clock signal is not being low, HOLD operation will not start until Serial Clock
signal being low). The HOLD condition ends on the rising edge of HOLD# pin signal while Serial Clock(SCLK) signal is
being low( if Serial Clock signal is not being low, HOLD operation will not end until Serial Clock being low), see Figure 1.
Figure 1. Hold Condition Operation
SCLK
HOLD#
Hold
Condition
(standard use)
Hold
Condition
(non-standard use)
The Serial Data Output (SO) is high impedance, both Serial Data Input (SI) and Serial Clock (SCLK) are don't care during
the HOLD operation. If Chip Select (CS#) signal goes high during HOLD operation, it has the effect on resetting the internal
logic of the device. It is necessary to drive HOLD# signal to high, and then to drive CS# to low for restarting communication
with the device.
P/N: PM1211
www.DataSheet.in
REV. 0.01, JUL. 29, 2005
6

6 Page



ページ 合計 : 41 ページ
 
PDF
ダウンロード
[ MX25L1605A データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
MX25L1605

16M-BIT [x 1] CMOS SERIAL FLASH

Macronix International
Macronix International
MX25L1605A

16M-Bit CMOS Serial Falsh

MXIC
MXIC
MX25L1605D

(MX25L1605D - MX25L6405D) 16M-BIT [x 1 / x 2] CMOS SERIAL FLASH

Macronix International
Macronix International
MX25L1605ZM

16M-BIT [x 1] CMOS SERIAL eLiteFlashTM MEMORY

Macronix International
Macronix International


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap