DataSheet.jp

CNH10F104Z-TM の電気的特性と機能

CNH10F104Z-TMのメーカーはMARUWAです、この部品の機能は「High capacitance 3-terminal capacitors」です。


製品の詳細 ( Datasheet PDF )

部品番号 CNH10F104Z-TM
部品説明 High capacitance 3-terminal capacitors
メーカ MARUWA
ロゴ MARUWA ロゴ 




このページの下部にプレビューとCNH10F104Z-TMダウンロード(pdfファイル)リンクがあります。
Total 1 pages

No Preview Available !

CNH10F104Z-TM Datasheet, CNH10F104Z-TM PDF,ピン配置, 機能
MARUWA GENERAL CATALOG
PERFORMANCE AND TEST METHOD
www.DataSheet4U.com
Item
Dissipation Factor
Withstanding voltage
Insulation resistance
Adhesion strength of termination
Vibration
resistance
Resistance
to soldering
heat
Visual
Capacitance
Dissipation factor
Visual
Capacitance
Dissipation factor
Insulation resistance
Withstanding voltage
Solderability
Temperature
cycling
Humidity
load test
Life test
at high
temperature
load
Visual
Capacitance
Dissipation factor
Insulation resistance
Withstanding voltage
Visual
Capacitance
Dissipation factor
Insulation resistance
Visual
Capacitance
Dissipation factor
Insulation resistance
Flexion
Visual
Capacitance
CG, UJ
Performance
2.5% or less ء1)
R
Testing method and conditions
F (In accordance with JIS C5101-1)
5% or less ء1)
CG : 1MHz
UJ, R, F
: 1kHz
Measurement voltage : 0.5~2Vrms
No insulation breakdown and no failure.
No less than 10,000Mor 500MF, whichever is smaller.
Application time is 1~5seconds.
CG, UJ : 300% of rated voltage
R, F : 250% of rated voltage
Rated voltage is applied for 1 minute.
Chip
5N
Substrate
No peeling-off or exfoliation shall be manifest or
recognizable in its incipient stages.
Solder a specimen on the testing jig shown on
the left and apply a force of 5N (0.51kgf) in the
direction indicated by arrow.
No remarkable damage
Within specified tolerance
Initial standard values must be satisfied.
No remarkable damage
No more than ȗ2.5% or ȗ0.25pF, whichever is larger.
Within ȗ7.5%
Initial standard values be satisfied.
Initial standard values be satisfied.
No damage or insulation breakdown.
Within ȗ20%
Vibration frequency : 10~55Hz
Full amplitude : 1.5mm, 10~55~10Hz 1min.
XYZ direction 2hrs for each total 6hrs.
Solder
: H60A or H63A (JIS Z 3282)
Soldering temperature : 270ȗ5°C
Immersion time
: 10ȗ1sec.
Preheat
: 80~100°C (1~2min.) and
170~200°C (1~min.)
Immersion into solder should be carried out
continuously after preheating.
Termination surface should be covered with new solder to over 75%.
Solder
: H60A or H63 (JIS Z 3282A)
Soldering temperature : 230ȗ5°C
Immersion time
: 2ȗ1sec.
No remarkable damage
No more than ȗ2.5% or ȗ0.25pF, whichever is larger.
Within ȗ7.5%
Initial standard values must be satisfied.
Initial standard values must be satisfied.
No damage or insulation breakdown.
No remarkable damage
Within ȗ20%
Step
1
2
3
4
Temperature
Lower limit temp.ء
Room temp.
Upper limit temp.ء
Room temp.
Time
30min.
3min.
30min.
3min.
These four temperatures in the above order
completes one cycle.
The cycle is repeated 25 times.
No more than ȗ5% or ȗ0.5pF, whichever is larger.
Within ȗ12.5%
Within ȗ30%
Less than 5% ء1)
Less than 7.5% ء1)
No less than 10,000Mor 500MF, whichever is smaller.
Test temp
: 40ȗ2°C
Relative humidity : 90~95%
Testing time
: 1000 +48, –0
100% of rated voltage is applied
No remarkable damage
No more than ȗ3% or ȗ0.3pF, whichever is larger
Within ȗ12.5%
Within ȗ30% Test temp : Upper limit temp.ȗ3°C
Testing time : 1000 +48, –0
Less than 4% ء1)
Less than 7.5% ء1) 200% of rated voltage is applied.ء2)
No less than 10,000Mor 500MF, whichever is smaller.
No mechanical damage
No more than ȗ5% or ȗ0.5pF, whichever is larger.
Within ȗ12.5%
Within ȗ30%
Add load at a speed of
about 1mm per second
until flexion amount
Unit : mm
10
20
reaches 1mm and keep
the condition
R=230
for 5 minutes.
Have a capacitance
meter connected to
both ends of sample
during a test.
45±2 45±2
*1) Dielectric dissipation factor
Type name
CNH20R224M–ȞM
CNH20R474M–ȞM
CNH20R105M–ȞM
CNH20R475M–ȞM
CNH20R106M–ȞM
CNH10R105M–ȞM
Temperature characteristics Rated voltage Initial
5% max.
16V
R
6.3V
9% max.
Moistureproof load High-temperature load
7.5% max.
7% max.
12.5% max.
12.5% max.
*2) The following products are applied voltage 150%.
CNH20R224M–ȞM
CNH20R474M–ȞM
CNH20R105M–ȞM
90
The following product is applied rated voltage
CNH20R475M–ȞM
CNH20R106M–ȞM
CNH10R105M–ȞM

1 Page







ページ 合計 : 1 ページ
 
PDF
ダウンロード
[ CNH10F104Z-TM データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
CNH10F104Z-TM

High capacitance 3-terminal capacitors

MARUWA
MARUWA


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap