|
|
PDF ISL97672 Data sheet ( Hoja de datos )
| Número de pieza | ISL97672 | |
| Descripción | 6-Channel LED Driver | |
| Fabricantes | Intersil | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ISL97672 (archivo pdf) en la parte inferior de esta página. Total 17 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
6-Channel LED Driver
ISL97672
The ISL97672 is an integrated power LED driver that
controls 6 channels of LED current for LCD backlight
applications. The ISL97672 is capable of driving up to
78 LEDs from 4.5V to 26V or 48 LEDs from a boost
supply of 2.7V to 26V and a separate 5V bias supply on
the VIN pin.
The ISL97672 compensates for non-uniformity of the
forward voltage drops in the LED strings with its 6 voltage
controlled-current source channels. Its headroom control
monitors the highest LED forward voltage string for output
regulation, to minimize the voltage headroom and power
loss in a typical multi-string operation.
The ISL97672 allows direct PWM mode by following the
external signal from 0Hz to 30KHz at 0.4% to 100% duty
cycle and maintaining a typical ±0.7% current matching
between channels.
The ISL97672 features a separate EN pin and extensive
protection functions that flag whenever a fault occurs.
The protections include string open and short circuit
detections, OVP, OTP, thermal shutdown and an optional
input overcurrent protection with fault disconnect switch.
Typical Application Circuit
VIN = 4.5V~26.5V
Features
• 6 Channels
• 4.5V to 26.5V Input
• 45V Output Max
• Up to 40mA LED Current per channel
• Direct PWM Dimming without Phase Shift
• PWM Dimming Linearity 0.4%~100% <30kHz
• Adjustable 200kHz to 1.4MHz Switching Frequency
• Dynamic Headroom Control
• Protections with Flag Indication
- String Open/Short Circuit, VOUT Short Circuit,
Overvoltage and Over-Temperature Protections
- Optional Master Fault Protection
• Current Matching ±0.7%
• 20 Ld 4mmx3mm QFN Package
Applications*(see page 16)
• Notebook Displays LED Backlighting
• LCD Monitor LED Backlighting
• Automotive Displays LED Backlighting
• Automotive or Traffic Lighting
VOUT = 45V*, 40mA PER STRING
ISL97672
1 FAULT
2 VIN
4 VDC
LX 20
OVP 16
18 COMP
6 /FLAG
PGND 19
CH0 10
5 PWM
3 EN
17 RSET
8 FSW
CH1 11
CH2 12
CH3 13
CH4 14
CH5 15
9 AGND
* VIN > 12V
FIGURE 1. ISL97672 TYPICAL APPLICATION DIAGRAM
June 24, 2010
FN7632.0
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2010. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
1 page  
ISL97672
www.DataSheet4U.com
Electrical Specifications
All specifications below are tested at TA = 25°C; VIN = 12V, EN = 5V, RSET = 20.1kΩ, unless
otherwise noted. Boldface limits apply over the operating temperature range,
-40°C to +85°C. (Continued)
PARAMETER
DESCRIPTION
CONDITION
MIN
MAX
(Note 8) TYP (Note 8) UNIT
REGULATOR
VDC
IVDC_STBY
LDO Output Voltage
Standby Current
VIN > 6V
EN = 0V
4.55
4.8
5
V
5 µA
IVDC
Active Current
EN = 5V
5 mA
VLDO
ENLow
VDC LDO Droop Voltage
Guaranteed Range for EN Input Low
Voltage
VIN > 5.5V, 20mA
20
200
mV
0.5 V
ENHi
Guaranteed Range for EN Input High
Voltage
1.8 V
tENLow
BOOST
EN low time before shut-down
30.5
ms
SWILimit Boost FET Current Limit
1.5 2.0
2.7
A
rDS(ON)
SS
Internal Boost Switch ON-Resistance
Soft-start
TA = +25°C
100% LED Duty Cycle
235 300 mΩ
7 ms
Eff_peak Peak Efficiency
ΔIOUT/ΔVIN
Dmax
Line Regulation
Boost Maximum Duty Cycle
VIN = 12V, 72 LEDs, 20mA
each, L = 10µH with DCR
101mΩ, TA = +25°C
VIN = 12V, 60 LEDs, 20mA
each, L = 10µH with DCR
101mΩ, TA = +25°C
FSW = 600kHz
90
92.9
90.8
0.1
%
%
%
%
FSW = 1.2MHz
81
%
Dmin
Boost Minimum Duty Cycle
FSW = 600kHz
9.5 %
FSW = 1.2MHz
17 %
fS Minimum Switching Frequency
fS Maximum Switching Frequency
ILX_leakage LX Leakage Current
CURRENT SOURCES
RFSW = 200kΩ
RFSW = 33kΩ
LX = 45V, EN = 0
175
1.312
200
1.50
235
1.69
10
kHz
MHz
µA
IMATCH
Channel-to-Channel Current Matching
IACC
Vheadroom
VRSET
ILEDmax
Current Accuracy
Dominant Channel Current Source
Headroom at IIN Pin
Voltage at RSET Pin
Maximum LED Current per Channel
FAULT DETECTION
RSET =20.1kΩ
(IOUT = 20mA)
ILED = 20mA
TA = +25°C
RSET = 20.1kΩ
VIN = 12V, VOUT = 45V,
Fsw = 1.2MHz,
TA = +25°C
-1.5
1.2
±0.7 ±1.0
+1.5
500
1.22
40
1.24
%
%
mV
mV
mA
VSC
Short Circuit Threshold
PWM Dimming = 100%
5.2 5.85 6.6
V
Temp_shtdwn Temperature Shutdown Threshold
150 °C
Temp_Hyst Temperature Shutdown Hysteresis
23 °C
5 FN7632.0
June 24, 2010
5 Page 
ISL97672
www.DataSheet4U.com
Fault Protection and Monitoring
The ISL97672 features extensive protection functions to
cover all the perceivable failure conditions. The failure
mode of a LED can be either open circuit or as a short.
The behavior of an open circuited LED can additionally
take the form of either infinite resistance or, for some
LEDs, a zener diode, which is integrated into the device
in parallel with the now opened LED.
For basic LEDs (which do not have built-in zener diodes),
an open circuit failure of an LED will only result in the loss
of one channel of LEDs without affecting other channels.
Similarly, a short circuit condition on a channel that
results in that channel being turned off does not affect
other channels unless a similar fault is occurring.
Due to the lag in boost response to any load change at its
output, certain transient events (such as LED current
steps or significant step changes in LED duty cycle) can
transiently look like LED fault modes. The ISL97672 uses
feedback from the LEDs to determine when it is in a
stable operating region and prevents apparent faults
during these transient events from allowing any of the
LED stacks to fault out. See Table 1 for more details.
A fault condition that results in an input current that
exceeds the devices electrical limits will result in a
shutdown of all output channels.
Short Circuit Protection (SCP)
The short circuit detection circuit monitors the voltage on
each channel and disables faulty channels which are
above approximately 5V (the action taken is described in
Table 1).
Open Circuit Protection (OCP)
When one of the LEDs becomes open circuit, it can
behave as either an infinite resistance or a gradually
increasing finite resistance. The ISL97672 monitors the
current in each channel such that any string which
reaches the intended output current is considered
“good”. Should the current subsequently fall below the
target, the channel will be considered an “open circuit”.
Furthermore, should the boost output of the ISL97672
reaches the OVP limit or should the lower
over-temperature threshold be reached, all channels
which are not “good” will immediately be considered as
“open circuit”. Detection of an “open circuit” channel will
result in a time-out before disabling of the affected
channel. This time-out is sped up when the device is
above the lower over-temperature threshold in an
attempt to prevent the upper over-temperature trip
point from being reached.
Some users employ some special types of LEDs that have
zener diode structure in parallel with the LED for ESD
enhancement and enabling open circuit operation. When
this type of LED is open circuited, the effect is as if the
LED forward voltage has increased but no lighting. Any
affected string will not be disabled, unless the failure
results in the boost OVP limit being reached, allowing all
other LEDs in the string to remain functional. Care should
be taken in this case that the boost OVP limit and SCP
limit are set properly, so as to make sure that multiple
failures on one string do not cause all other good
channels to be faulted out. This is due to the increased
forward voltage of the faulty channel making all other
channels look as if they have LED shorts. See Table 1 for
details regarding responses to fault conditions.
Overvoltage Protection (OVP)
The integrated OVP circuit monitors the output voltage
and keeps the voltage at a safe level. The OVP threshold
is set as Equation 5:
OVP = 1.21V × (RUPPER + RLOWER) ⁄ RLOWER
(EQ. 5)
These resistors should be large to minimize the power
loss. For example, a 1MkΩ RUPPER and 30kΩ RLOWER sets
OVP to 41.2V. Large OVP resistors also allow COUT
discharges slowly during the PWM Off time. Parallel
capacitors should also be placed across the OVP resistors
such that RUPPER/RLOWER = CLOWER/CUPPER. Using a
CUPPER value of at least 30pF is recommended. These
capacitors reduce the AC impedance of the OVP node,
which is important when using high value resistors.
Undervoltage Lockout
If the input voltage falls below the UVLO level of 2.45V,
the device will stop switching and be reset. Operation will
restart only if the VIN is back in the normal operating
range.
Input Overcurrent Protection
During normal switching operation, the current through
the internal boost power FET is monitored. If the current
exceeds the current limit, the internal switch will be
turned off. This monitoring happens on a cycle-by-cycle
basis in a self protecting way.
Additionally, the ISL97672 monitors the voltage at the LX
and OVP pins. At start-up, a fixed current is injected out
of the LX pins and into the output capacitor. The device
will not start-up unless the voltage at LX exceeds 1.2V.
The OVP pin is also monitored such that if it rises above
and subsequently falls below 20% of the target OVP
level, the input protection FET will also be switched off.
Over-Temperature Protection (OTP)
The ISL97672 includes two over-temperature thresholds.
The lower threshold is set to +130°C. When this
threshold is reached, any channel which is outputting
current at a level significantly below the regulation target
will be treated as “open circuit” and disabled after a time-
out period. This time-out period is also reduced to 800µs
when it is above the lower threshold. The intention of the
lower threshold is to allow bad channels to be isolated
and disabled before they cause enough power dissipation
(as a result of other channels having large voltages
across them) to hit the upper temperature threshold.
The upper threshold is set to +150°C. Each time this is
reached, the boost will stop switching and the output
current sources will be switched off. Once the device has
11 FN7632.0
June 24, 2010
11 Page | ||
| Páginas | Total 17 Páginas | |
| PDF Descargar | [ Datasheet ISL97672.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ISL97671 | 6-Channel SMBus/I2C or PM Dimming LED Driver | Intersil |
| ISL97671A | 6-Channel SMBus/I2C or PWM Dimming LED Driver | Intersil |
| ISL97672 | 6-Channel LED Driver | Intersil |
| ISL97672A | 6-Channel LED Driver | Intersil |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |