|
|
Número de pieza | HL-112H193WC | |
Descripción | LED | |
Fabricantes | HongLitronic | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de HL-112H193WC (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
No Preview Available ! ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Features
•φ5 Super Flux LEDs
•LOW POWER CONSUMPTION.
•WIDE VIEWING ANGLE.
•IDEAL FOR BACKLIGHT、LIGHTING
AND INDICATOR.
•PACKAGE: 60PCS / PIPE.
Package Dimensions
7.62
www.DataSheet4U.com
HL-112H193WC
HL-112H193WC
Description
This devices are made with TS InGaN.
4.8
++
φ5.0
1、2
1.6
0.7
--
2.5
3、4
1.5C
2.5
1、2
3、4
SPEC NO.:
Tolerance
Dimension Tolerance (UNIT:mm)
Grade
0.5~3
3~6
6~30
Medium(m)
±0.1
±0.2
±0.3
Chip Lens Color
Material
InGaN
Emitting Color
White
Water Clear
30~120
±0.5
REV NO.:A/2
DATE:Apr/28/2008
PAGE:1/5
1 page www.DataSheet4U.com
HL-112H193WC
Package means
9.6
8.6
0.5
4.6
5.6
2.4
2.5
Lable 486.0
D:\My Documents\My Pictures\121.jpg
PART NO:HL-
广州市鸿利光电子有限公司
DATE:2006- -
Q'TY:60PCS
BIN COOD:
Notes: Each Adhesive Pipe 60pcs.
Soldering:
1. Manual Of Soldering
The temperature of the iron tip should not be higher than 260℃(500℉) and Soldering within 3 seconds per
solder-land is to be observed.
2. DIP soldering (Wave Soldering):
Preheating:120℃~150℃,within 120~180 sec.
Operation heating:245℃±5℃ within 5 sec.260℃(Max)
Gradual Cooling (Avoid quenching).
Handling:
Care must be taken not to cause to the epoxy resin portion of LED while it is exposed to high temperature.
Care must be taken not rub the epoxy resin portion of LED with hard or sharp article such as the sand blast
and the metal hook.
Care must be taken there should be more than 3mm from jointing point to the epoxy resin.
Notes for designing:
Care must be taken to provide the current limiting resistor in the circuit so as to drive the LED within the
rated figures .Also caution should be taken not to overload LED with exorbitant voltage at the turning ON
and OFF of the circuit.
When using the pulse drive care must be taken to keep the average current within the rated figures .Also the
circuit should be designed so as be subjected to reverse voltage when turning off the LED.
Storage:
In order to avoid the absorption of moisture . it is recommended to solder LED as soon as possible after
unpacking the sealed envelope.
If the envelope is still packed to store it in the environment as following:
Temperature:-5℃~45℃(23℉~113℉)Humidity : RH 60% Max.
SPEC NO.:
REV NO.:A/2
DATE:Apr/28/2008
PAGE:5/5
5 Page |
Páginas | Total 5 Páginas | |
PDF Descargar | [ Datasheet HL-112H193WC.PDF ] |
Número de pieza | Descripción | Fabricantes |
HL-112H193WC | LED | HongLitronic |
HL-112H193WC | LED | HongLitronic |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |