DataSheet.jp

STD02N の電気的特性と機能

STD02NのメーカーはSanken electricです、この部品の機能は「Darlington Transistors for Audio Amplifiers」です。


製品の詳細 ( Datasheet PDF )

部品番号 STD02N
部品説明 Darlington Transistors for Audio Amplifiers
メーカ Sanken electric
ロゴ Sanken electric ロゴ 




このページの下部にプレビューとSTD02Nダウンロード(pdfファイル)リンクがあります。
Total 9 pages

No Preview Available !

STD02N Datasheet, STD02N PDF,ピン配置, 機能
STD02N and STD02P
www.DataSheet4U.com
Darlington Transistors for Audio Amplifiers
Features and Benefits
Built-in temperature compensation diodes
High power (130 W) handling in a small package
(TO-3P), for minimized heat sink requirements
Built-in drivers and temperature compensation diodes,
reducing external component count and simplifying
circuit design
NPN and PNP versions
Emitter terminals placed symmetrically, pin 5 on NPN
and pin 1 on PNP models, allowing adjacent placement on
PCB to minimize trace length and output skew when used
in pairs
Approved by major manufacturers
Package: 5 pin TO-3P (MT-100)
Description
The STD02N and STD02Pare enhanced Darlington transistors
with built-in drivers and temperature compensation diode.
Manufactured using the unique Sanken thin-wafer production
technology, these devices achieve higher power levels through
decreased thermal resistance, and can withstand higher voltages
than similar devices on the market.
The temperature compensation diode is integrated on the same
chip as the power transistors. By this design, the STD02N and
STD02P eliminate delays that would otherwise be induced
between thermal sensing at the heat source, and the operation of
the compensation circuitry. Thus, these transistors are ideal for
applications where enhanced thermal stability is required.
This device is provided in a 5-pin TO-3P plastic package with
pin 4 removed. Contact Sanken™ for application support and
additional information on device performance.
Applications include:
General amplifier applications
Professional audio amplifiers
Car audio amplifiers
STD02N
STD02P
Not to scale
12345
12345
Emitter pins symmetrical
Equivalent Circuits
STD02N
3
1
4
STD02P
1
25
5
3
Datasheet 28104.021

1 Page





STD02N pdf, ピン配列
STD02N and
STD02P
Darlington Transistors for Audio Amplifierswww.DataSheet4U.com
12
10
IC vs. VCE
8
6
4
2
0
0
12
10
IC vs. VBE
VCE = 4 V Continuous
8
6
4
2
0
0
10
IF vs. VF
For Diode
STD02N Performance Characteristics at TA = 25°C
1.2 mA
1.0 mA
0.8 mA
0.6 mA
0.4 mA
3
VCE(sat) vs. IB
2
1
IB= 0.2 mA
24
VCE (V)
6
0
0.0001
106
0.001
0.01
IB (A)
10 A
7A
IC= 5 A
0.1 1
105
hFE vs. IC
104
VCE = 4 V Continuous
103
125°C
25°C
–30°C
0.5 1.0
1.5 2.0
VBE (V)
2.5
102
0.1
100.0
Safe Operating
Area
Single pulse
No heatsink
Natural cooling
TA=25°
10.0
1.0
0.1
1
IC (A)
10
DC10010mms s
100
1
0
10.00
RθJA vs. t
1.00
0.10
0.5 1.0
1.5 2.0
VF (V)
0.01
1
130
100
PC vs. TA
50
10 100
VCE (V)
1000
0.01
1
10 100
t (ms)
1000
3.5
0
0
Without Heatsink
25 50 75 100 125 150
TA (°C)
Sanken Electric Co., Ltd.
3-6-3 Kitano, Niiza-shi, Saitama-ken
352-8666, Japan
Phone:+81-48-472-1111
http://www.sanken-ele.co.jp
3


3Pages


STD02N 電子部品, 半導体
STD02N and
STD02P
Darlington Transistors for Audio Amplifierswww.DataSheet4U.com
WARNING — These devices are designed to be operated at lethal voltages and energy levels. Circuit designs
that embody these components must conform with applicable safety requirements. Precautions must be
taken to prevent accidental contact with power-line potentials. Do not connect grounded test equipment.
The use of an isolation transformer is recommended during circuit development and breadboarding.
Because reliability can be affected adversely by improper storage environments and handling methods, please
observe the following cautions.
Cautions for Storage
• Ensure that storage conditions comply with the standard temperature (5°C to 35°C) and the standard relative
humidity (around 40 to 75%); avoid storage locations that experience extreme changes in temperature or
humidity.
• Avoid locations where dust or harmful gases are present and avoid direct sunlight.
• Reinspect for rust in leads and solderability of products that have been stored for a long time.
Cautions for Testing and Handling
When tests are carried out during inspection testing and other standard test periods, protect the products from
power surges from the testing device, shorts between adjacent products, and shorts to the heatsink.
Remarks About Using Silicone Grease with a Heatsink
When silicone grease is used in mounting this product on a heatsink, it shall be applied evenly and thinly. If more
silicone grease than required is applied, it may produce stress.
Volatile-type silicone greases may produce cracks after long periods of time, resulting in reduced heat radiation
effect. Silicone grease with low consistency (hard grease) may cause cracks in the mold resin when screwing the
product to a heatsink.
Our recommended silicone greases for heat radiation purposes, which will not cause any adverse effect on the
product life, are indicated below:
Type
G746
YG6260
SC102
Suppliers
Shin-Etsu Chemical Co., Ltd.
Toshiba Silicone Co., Ltd.
Dow Corning Toray Silicone Co., Ltd.
Heatsink Mounting Method
Torque When Tightening Mounting Screws. Thermal resistance increases when tightening torque is low, and radiation
effects are decreased. When the torque is too high, the screw can strip, the heatsink can be deformed, and distortion
can arise in the product frame. To avoid these problems, observe the recommended tightening torques for this product
package type, TO-3P (MT-100): 0.686 to 0.882 N•m (7 to 9 kgf•cm).
Diameter of Heatsink Hole: < 4 mm. The deection of the press mold when making the hole may cause the case material
to crack at the joint with the heatsink. Please pay special attention for this effect.
Soldering
• When soldering the products, please be sure to minimize the working time, within the following limits:
260±5°C 10 s
350±5°C 3 s
Soldering iron should be at a distance of at least 1.5 mm from the body of the products
Electrostatic Discharge
• When handling the products, operator must be grounded. Grounded wrist straps worn should have at least 1 MΩ
of resistance to ground to prevent shock hazard.
• Workbenches where the products are handled should be grounded and be provided with conductive table and
floor mats.
• When using measuring equipment such as a curve tracer, the equipment should be grounded.
• When soldering the products, the head of soldering irons or the solder bath must be grounded in other to prevent
leak voltages generated by them from being applied to the products.
• The products should always be stored and transported in our shipping containers or conductive containers, or be
wrapped in aluminum foil.
Sanken Electric Co., Ltd.
3-6-3 Kitano, Niiza-shi, Saitama-ken
352-8666, Japan
Phone:+81-48-472-1111
http://www.sanken-ele.co.jp
6

6 Page



ページ 合計 : 9 ページ
 
PDF
ダウンロード
[ STD02N データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
STD02N

Darlington Transistors for Audio Amplifiers

Sanken electric
Sanken electric
STD02P

Darlington Transistors for Audio Amplifiers

Sanken electric
Sanken electric


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap